Extron electronics HDP 101 4K User Manual

HDP1014K • User Guide

The Extron HDP1014K is a compact, active HDMI to DisplayPort converter for signals up to 4K 30 Hz @ 4:4:4. It converts HDMI signals for connection to DisplayPort displays or peripherals. Incoming HDMI signals are equalized up to 15 feet (4 meters) at the input to compensate for signal loss. The HDP1014K features EDID Minder®, which maintains continuous EDID communication with connected devices and ensures that the HDMI source powers up properly and maintains correct video output. Audio information is passed between source and display.

The HDP1014K supports digital video resolutions of up to 4K/30 at 4:4:4 (or 10.2 Gbps) and is DisplayPort 1.2, HDMI 1.4, and HDCP 1.4 compliant.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

NOTES:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables must be used to ensure

compliance with FCC emissions limits.

• For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related

topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.

Speciﬁcations

Product specifications are available on the Extron website, www.extron.com.

Features

• Provides connectivity between HDMI sources and DisplayPort displays and peripherals.

• Supports computer and video resolutions up to 4K/30 @ 4:4:4 with data rates up to 10.2 Gbps.

• Supported HDMI speciﬁcation features include data rates up to 10.2 Gbps, 3D, Lip Sync, and HD lossless audio

formats.

• Equalizes incoming HDMI signals up to 15 feet (4 meters) to compensate for signal loss due to low quality cables or

marginal sources.

• EDID Minder automatically manages EDID communication between connected devices — EDID Minder ensures that all

sources power up properly and reliably output content for display.

• Selectable resolutions and refresh rates — Pre-stored EDID is communicated to the source based on a user-selected

resolution and refresh rate.

• EDID capture mode — When connected to a display, the HDP1014K offers the option of capturing and then storing EDID

information from the display device.

• Complies with HDMI and VESA Interoperability Guidelines.

• HDCP 1.4 compliant — The HDP 101 4K ensures display of content-protected media and interoperability with earlier

versions of HDCP-compliant devices.

• LED indicator for signal presence and power — Provides visual indication of system status for real-time feedback and

monitoring of key performance parameters.

• Front panel USB configuration port — Provides convenient access for setup, conguration, and rmware updates.

• Easy setup and commissioning with Extron PCS – Product Configuration Software — Conveniently congure multiple

products using a single software application.

• Compact 1 inch (2.5 cm) high, 2.2 inch (5.6 cm) wide enclosure for discreet placement and mounting in space-

constrained environments — Includes fabric hook and loop tape for easy installation in any application.

HDP 101 4K • User Guide (Continued)

• Includes LockIt® HDMI cable lacing brackets.

• Supports LPCM audio.

• Highly reliable, energy-efﬁcient external universal power supply included — Provides worldwide power compatibility,

with high demonstrated reliability and low power consumption for reduced operating costs.

Application Diagram

Figure 1. HDP1014K Application

Laptop

HDMI

Blu-ray Disc

POWER

SIG

12V

--A MAX

Extron HDP 101 4K

HDMI to DisplayPort Converter

HDMI

DP OUT

DisplayPort

4K Display

Mounting

Use the included hook-and-loop tape to attach the HDP1014K to the application surface.

HDP 101 4K • User Guide (Continued)

Smooth

Power Supply Output Cord

Cabling

CONFIG

HDMI IN

Figure 2. HDP1014K Panels

Config port — Connect a host computer to this mini-B USB port to configure the HDP1014K.

HDMI input — Connect an HDMI source device to the HDMI input.

NOTE: Extron recommends using HDMI Pro Series cables for 300 Mhz pixel clock (4K/UHD) signals.

Power inlet — Wire the external 12 VDC power supply as shown below, and connect it to the two-pole captive screw Power

connector.

SECTION A–A

Figure 3. Wiring the Power Connector

ATTENTION:

• The length of the exposed wires in the stripping process is critical. The ideal length is 3/16 inches (5 mm). Any

longer and the exposed wires may touch, causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les dénuder. La longueur idéale est de

5mm (3/16inches). S’ils sont un peu PLUS longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont un peu PLUS courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.

• Always use a power supply supplied by or specied by Extron. Use of an unauthorized power supply voids all

regulatory compliance certication and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non

autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended for use with a UL Listed power source marked “Class

2” or “LPS” rated 12 VDC, 0.5 A minimum.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être utilisé avec une source d’alimentation

certiée UL de classe 2 ou LPS avec une tension nominale de 12 Vcc, 0.5 A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium, or desk.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces

d’aération ou dans les cavités murales. La source d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel dans un endroit ordinaire, avec un degré2 de pollution, xé à un équipement de rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/

NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently xed to building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/

NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être xée de façon permanente à une structure de bâtiment ou à une structure similaire.

HDP 101 4K

Ridges

POWER

12V

0.1A MAX

SIG

DP OUT

3/16"

(5 mm) Max.

Config port

HDMI input

Power inlet

DP output

DP output — Connect a DisplayPort device to the DP output.

HDP 101 4K • User Guide (Continued)

DP OUT

SIG

POWER

12V

0.1A MAX

HDP 101 4K

CONFIG

HDMI IN

A BD

Space

LED Indicators

CONFIG

HDMI IN

HDP 101 4K

POWER

12V

0.1A MAX

SIG

DP OUT

Power and signal LED (front) — Lights amber to indicate power,

and lights green to indicate HDMI signal presence.

Output signal LED (rear) — Lights green to indicate signal

presence on the DisplayPort output.

Figure 4. HDP1014K LED Indicators

Firmware Upgrades

The HDP1014K rmware can be upgraded via Product Conguration Software (PCS) or the Extron Firmware Loader program (available at www.extron.com).

SIS Commands

The HDP1014K can be congured with specic SIS commands via a USB connection. Use the Extron DataViewer utility or a control system to send and receive SIS commands. SIS commands consist of one or more characters per eld. No special characters are required to begin or end a command sequence. When the HDP1014K recognizes a valid command, it executes the command and sends a response to the host device. All responses from the receiver to the host end the character string with a carriage return and a line feed (CR/LF = ]). A string is one or more characters.

When the HDP1014K is rst switched on, it sends the message:

• Vx.xx is the rmware version number.

• 60-xxxx‑xx is the part number of the device.

Error Responses

When the HDP1014K receives a valid SIS command, it executes the command and sends a response to the host device. If the HDP1014K is unable to execute the command because the command is invalid or contains invalid parameters, it returns the following error responses to the host:

• E10 – Invalid command

• E13 – Invalid parameter

Using the Command and Response Table

The Command and Response Table for SIS Commands starting on page6 lists the following:

• Valid ASCII command codes

• The device response to the host

• A description of the command function, or the results of executing the command

The ASCII to hexadecimal conversion table below is for use with the command and response table:

ASCII to Hex Conversion Table

•

HDP 101 4K • User Guide (Continued)

Command and Response Table for SIS Commands

Carriage return and line feed (LF)

]

Carriage return with no line feed

}

Pipe (can be used interchangeably with the } character).

Space

•

Escape key

Can be used interchangeably with the E character.

X! =

Status

0 = Off/low/undetected 1 = On/high/detected

EDID: 1 to 3 (see table)

X$ =

1 Input 1 (Store) Slot HDMI 1080p 60 Hz 2-Ch Default

2 Output

3 User Loaded Slot Manually populated via PCS

Verbose mode:

X% =

0 = Clear/none 1 = Verbose mode (default) 2 = Tagged responses for queries 3 = Verbose mode and tagged responses for queries

HDP1014K part number 60-1739-01

X^ =

Text string of up to 24 alphanumeric characters and hyphen (-). No spaces allowed, and no distinction between upper and

X& =

lower case. First character must be a letter and the last must not be a hyphen. Default is “HDP-101-4K”.

Slot Default EDID Details

NOTE: Upper- and lowercase characters can be used interchangeably in the command field unless otherwise specified.

HDP 101 4K • User Guide (Continued)

Command and Response Table for SIS Commands

Command ASCII Command

(Host to Device)

Signal Status

Input and output signal status

E0LS} X!•X!]

EDID Assignment

Assign EDID slot to input

View EDID assignment

EA X$

EDID} Edid A

EDID} X$]

Verbose Mode

Set verbose mode

View verbose mode

EX%

CV} Vrb

ECV} X%]

Unit Name

Set the unit name

Set unit name to factory default

View unit name

EX&

CN} Ipn

CN} Ipn•HDP-101-4K]

•

ECN} X&]

Information and Other Queries

Query part number

Query Firmware version

Query Firmware version with build

Query model name

Query model description

Reset to factory default settings

Q n.nn

*Q n.nn.nnnn

ZXXX} Zpx]

Response

(Device to Host)

Sig

X!•X!]

X$] X$: 1 = default

EdidA

X$]

X%] X%: 1 = default

Vrb

X%]

X&]

•

Ipn

X&]

•

X^]

Pno

X^]

•

HDP•101•4K] Inf01•HDP101•4K]

HDMI•TO•DP•4K•30] Inf02•HDMI•TO•DP•4K•30]

Additional Description

Input*output (unsolicited) Verbose mode 2/3

Verbose mode 2/3

Up to 24 alphanumeric characters including "-"

Verbose mode 2/3

NOTE:

X! =

Status — 0 = Off/low/undetected, 1 = On/high/detected

EDID: 1 to 3 (see table on previous page)

X$ =

Verbose mode — 0 = Clear/none, 1 = Verbose mode (default), 2 = Tagged responses for queries, 3 = Verbose mode and

X% =

tagged responses for queries

HDP1014K part number 60-1739-01

X^ =

Text string of up to 24 alphanumeric characters and hyphen (-). No spaces allowed, and no distinction between upper and

X& =

lower case. First character must be a letter and the last must not be a hyphen. Default is “HDP-101-4K”.

HDP 101 4K • User Guide (Continued)

Product Conﬁguration Software

The HDP1014K uses Extron Product Conguration Software (PCS) to congure and reset the unit, as well as upload rmware.

Download Software from the Extron Website

Visit www.extron.com to download the latest version of PCS.

NOTE: Also download the latest versions of software and firmware for the HDP1014K. To update firmware, use PCS or

download and install Firmware Loader.

1. Click the Download link at the top of the Extron website (see figure5 ,

Figure 5. Software and Firmware Links on Download Page

2. Click the appropriate link on the left sidebar menu (

For software, either click the Software link at the top of the sidebar or, if the software is listed in the sidebar, click directly on that link (for example, see the PCS link in figure5 , 2).

3. If there is no direct link to the software or rmware, scroll down to the alphabetic navigation bar (see gure 6).

Figure 6. Alphabetic Navigation Bar

4. Click the appropriate letter to locate the software or rmware (for example, click H for the HDP1014K).

5. Click Download and follow the on-screen instructions.

Using PCS

1. Connect the control PC, with PCS installed, to the HDP1014K. The Windows-based PCS communicates with the device via

the Front Panel Conguration port (see ﬁgure2, A page 3) with a standard USB mini-B connector.

2. Open PCS on the control PC from the PCS icon loaded on the desktop (optional, see image on the right) or

from the Start menu:

Start>Programs>Extron Electronics>Extron Product Configuration Software>Extron Product Configuration Software

The Product Conguration Software opens to the Device Discovery screen:

Figure 7. PCS Device Discovery Screen

HDP 101 4K • User Guide (Continued)

3. Select the HDP1014K device by clicking on it to highlight it in the list (see ﬁgure7,

on the previous page).

NOTE: If the device does not appear in the list and one or more network adapters are being used, click on the Network

Adapter button (3) to select the appropriate adapter.

4. Click Connect (

The Product Configuration Software opens to the device main menu.

1 2

Figure 8. HDP1014K PCS Main Menu

The conguration pages have a global navigation bar (see figure8) from which each of the individual conguration pages can be accessed.

These pages are:

5. Select either of these pages to begin conguring the HDP1014K.

Input/Output Configuration

EDID Minder

Input/Output Conﬁguration

This page allows users to view the status of the input and congure the output.

Input Conﬁguration

Figure 9. Input Conﬁguration Panel

The Input Configuration panel (see figure9) allows the user to view the signal presence of the input.

• Signal Presence — Connection status icon shows green when an active HDMI signal is present.

HDP 101 4K • User Guide (Continued)

Output Conﬁguration

Figure 10. Output Conﬁguration Panel

• Signal Presence — Signal status icon shows green when an active DisplayPort signal is present (see figure10).

EDID Minder

EDID Minder is an EDID process that manages the resolution and refresh rate between the HDP1014K HDMI input and the DisplayPort output source. Click the EDID Minder icon (see figure11, 1) on the global navigation bar to open the EDID Minder page. EDID can be set to match output rate, a custom user-dened EDID, or a factory setting.

3 4

Figure 11. EDID Minder Page

Filtering Available EDID

Use the Filter tab (2) to limit the number of available EDID displayed in the Favorites, Connected Output, and Available EDID panels.

1. From the Resolution drop-down menu (

2. From the Refresh Rate drop-down menu (

3. From the Video Format drop-down menu (

4. From the Audio Format drop-down menu (

), select a specic resolution or Any.

), select a specic refresh rate or Any.

), select HDMI or Any.

), select LPCM 2-Ch, None or Any.

HDP 101 4K • User Guide (Continued)

Assigning EDID

To assign EDID to the input:

1. From the Input box on the right (see ﬁgure11,

2. From the Favorites, Available EDID, or Connected Output panel on the left, select the desired EDID.

3. Then either:

• Click the Assign button (

• Drag and drop the EDID image from the Favorites, Available EDID, or Connected Output panels to the Input box.

) to assign EDID to the input.

Adding EDID to the EDID Library

1. Click the Add EDID to Library button (see ﬁgure11,

window opens (see figure12).

on the previous page), select the input.

on the previous page). The Browse Add EDID to Library

Figure 12. Browse Add EDID to the Library Window

2. Navigate to the desired EDID le location and select it (

NOTE: Valid EDID files have a .bin file extension.

3. Click the Open button (

). The EDID is added to the Available EDID panel.

Device Menu

Disconnect the device from PCS

View the hardware Settings

Reset Device to factory default

Update Firmware

View information About this Module

Extron PCS Help File

For assistance, Extron PCS Help contains complete information about using the program to congure the HDP1014K.

To access Extron PCS Help, click the button in the top right corner of the PCS program screen (see the image on the right, 1) and click on Extron PCS Help(2).

68-3198-01

Rev. A 02 18

Extron electronics HDP 101 4K User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual