Extron Electronics HDMI DA6 Setup Guide
HDMI DA4 and HDMI DA6 • Setup Guide
36
Overview
These Extron distribution ampliers distribute one HDMIinput signal to four (HDMI DA4) or six (HDMI DA6) simultaneous outputs.
This setup guide provides basic instructions for installation by an experienced installer. For complete instructions, see the
HDMIDA4 and HMDI DA6 User Guide, on the Extron web site (www.extron.com).
Front Panel
3
INPUT OUTPUTS
CONFIG
SIGNAL
HDCP
1234
EDID
HDMI DA4
HDMI DISTRIBUTION AMPLIFIER
1 2
4 5
3
INPUT OUTPUTS
CONFIG
SIGNAL
HDCP
1234
1 2
Power status LED — Lights green when power is applied to the unit.
a
USB Config port — Used for SIS configuration, monitoring, and firmware updates.
b
Signal LEDs — Light green when a TMDS signal is detected on the HDMI input and is being transmitted on the
c
56
HDMI DA6
HDMI DISTRIBUTION AMPLIFIER
4 5
EDID
corresponding output.
HDCP LEDs — Light green when a HDCP has been authenticated on the HDMI input and the appropriate output (if required).
d
EDID LED — Lights green when the EDID from the selected output device (output 1 by default) is successfully stored. Lights
e
amber if factory-installed EDID is used or if the EDID was not successfully stored.
Rear Panel
100-240V ~ 0.3 A MAX
50/60 Hz
HDMI DA4
REMOTEOUTPUTSINPUT
4321
RS-232
Tx Rx G
3 41 2
100-240V ~ 0.3 A MAX
50/60 Hz
HDMI DA6
OUTPUTS REMOTEINPUT
4
521
RS-232
Tx Rx G
a Power input — Connect the provided IEC connector to a 100-240 VAC (50 or 60 Hz) power source..
b HDMI input — Connect a source device into this female HDMI type A connector.
c HDMI outputs — Connect display devices into these female HDMI type A connectors.
d RS-232 — Used for SIS conguration, monitoring, and rmware updates.
1
HDMI DA4 and HDMI DA6 • Setup Guide (Continued)
Installation
1. Mount the HDMI DA in a suitable location (see the “Mounting” section of the HDMI DA4 and HDMI DA6 User Guide for
mounting options). Follow the instructions provided with the mounting kit.
2. (Optional) Connect the USB or RS-232 connector (see the gure below) to a PC for conguration and maintenance.
Use SIS commands to congure EDID Minder®, mute the video signal, mute the audio signal, adjust the video color bit
depth, or monitor the signal and HDCP status, as required. See the “SIS Commands” section of the HDMIDA4 and
HDMIDA6UserGuide.
51
96
DB9 Pin Locations
Female
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
TransmitReceive
ReceiveTransmit
GroundGround
Computer HDMI DA2
3. Connect and power on the display devices to the rear panel HDMI outputs. Connect the primary display to output 1. EDID
from output 1 is stored automatically, by default.
REMOTE
RS-232
Tx Rx G
NOTE: Use the LockIt
™
HDMI cable lacing brackets provided to secure the HDMI connectors (see the
LockItHDMICable Lacing Bracket Installation Guide).
4. Connect to a 110-240 VAC (50 or 60 Hz) power supply using the provided IEC power cord.
5. Connect and power on the source device.
Typical Application (showing HDMI DA4)
Extron
HDMI DA4
Distribution
Amplier
4321
HDMI DA4
100-240V ~ 0.3 A MAX
50/60 Hz
TouchLink
Control
System
REMOTEOUTPUTSINPUT
RS-232
TxRx G
®
100
RELAY
LINK
ACT
3
INPUT
1
31
IR
4
31
2
COM
42
TXRX
1
IPL 250
42
2
R
3
HDMI
Cables
ON
OFF
DISPLAY
MUTE
SCREEN
UP
SCREEN
DOWN
TCP/IP
VCR
DVD
DOC
CAM
LAPTOP
PC
RS-232
Blu-ray Player
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
2
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Flat Panel Displays
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
68-1844-51 Rev. A
06 13
Loading...