Extron Electronics GMK 1 User Manual

GMK 1 • Installation Guide

ape

Level

(bottom) edge

(4) Studs

The Extron GMK 1 (see gure to the right) is an accessory for the SMB1 kit and is used to mount the TLP Pro 320M or the TLP Pro 520M on a glass surface. This guide provides instructions for experienced, professional installers to mount and install either touchpanel using the GMK 1 and SMB 1 mounting kits.

The GMK 1 is a at plate with a powerful adhesive on one surface that bonds strongly to a glass surface. The opposite surface has four studs (one in each corner) for securing the SMB 1.

Refer to www.extron.com for the complete TLP Pro 320m and TLP Pro 520M user guide

and installation instructions before

connecting the product to the power source.

ATTENTION: The installation shall be in accordance with the

applicable provisions of National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16.

NOTE: The diagrams in this guide show the TLP Pro 520M. The

TLPPro 320M is mounted in exactly the same way.

Securing the GMK 1 to a Glass Surface

1. Decide where the touchpanel will be placed and clean

the surface of the glass with a 50:50 mixture of isopropyl alcohol and water.

2. Use a level and apply painter tape to the glass to mark

the position where the GMK 1 will be mounted.

ATTENTION: The lower edge of the GMK 1 is the

shorter edge with the notch.

3. Remove the backing from the surface of the GMK 1 to

expose the adhesive.

4. Carefully align the lower edge of the GMK 1 with the

tape from step 2. Hold the GMK 1 at a slight angle so that the adhesive does not come in contact with the glass until you are ready to press it into place.

ATTENTION:

• Once the GMK 1 is attached to the glass, it

is very difcult to remove. Align the GMK 1 exactly where you need it before pressing it into place.

• If you need to remove the plate, slide a thin

wire or use a ne tooth saw or other sharp cutting tool between the plate and the glass. Once the plate has been removed from the glass, it should not be reattached.

GMK 1

Notch in shorter

Remove Backing

Align GMK 1 with Painter T

Painter Tape

5. Once aligned, angle the GMK 1 onto the glass and press

rmly. If possible, allow the bond to set for 72 hours for maximum strength.

CAUTION: The maximum load for the GMK 1

must not exceed 5 lb (2.27 kg).

GMK-1 • Setup Guide (Continued)

Cable Racewa (not included)

Mounting Plate

Mounting the SMB 1 on the GMK 1

6. Align the four holes on the back of the SMB 1 with the

four studs on the GMK 1. Secure the SMB 1 to the GMK1 using the four provided nuts. Do not overtighten the nuts.

ATTENTION: The SMB 1 must be mounted so

that the touchpanel faces upwards and the cutout for the cable is at the bottom.

Mounting Screws (4)

Mounting Nuts (4)

GMK 1

Installing the Touchpanel in the SMB 1

7. Secure the wall plate adapter to the SMB 1, using the four provided

screws.

8. Run cables through the cable cutout and connect them to the back

panel of the touchpanel (see the TLP Pro 320M User Guide or the TLPPro 520M User Guide at www.extron.com).

If required, mount an adhesive raceway (not provided) to run the cable (see the gure below).

9. Press the touchpanel onto the wall plate adapter. Four catches hold it

in place.

10. If the bezel has been removed, snap it back into place.

NOTE: The bezel for the touchpanels can be removed using the

provided Extron removal tool.

Wall Plate Adapter

TLP Pro 520M

SMB 1

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673 (Inside Europe Only)

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+65.6383.4400 +65.6383.4664 FAX

Extron Japan

+81.3.3511.7655 +81.3.3511.7656 FAX

Extron China

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800 +971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571 +82.2.3444.1575 FAX

Extron India

1800.3070.3777 Inside India Only

+91.80.3055.3777 +91.80.3055.3737 FAX

68-2296-01 A

02 14