Extron electronics FOX II T HD 4K Setup Manual
specifications bef
oduct to the po
FOX II T HD 4K Transmitter Rear Panel
HDMI LOOP THRU
LR
AUDIO
LR
AUDIO
IR Device
RS-232 Device
Unbalanced Stereo Output Balanced Stereo Output
Do not tin the wires!
FOX II T HD 4K • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
pr
ore connecting the
wer source.
the Extron FOX II T HD 4K Fiber Optic Transmitter. The transmitter is compatible with all Extron
FOX II receivers.
WARNING: The FOX II T HD 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.
Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX II T HD 4K User Guide, at www.extron.com.
AVERTISSEMENT : Le FOX II T HD 4K émet une lumière invisible en continu (conforme à la classe1) qui peut être dangereux
pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque
le câble bre optique est débranché.
Produit laser de classe1, voir le FOX II T HD 4K User Guide sur www.extron.com (en anglais).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power
sources and mount the transmitter as required.
For mounting details and considerations, see the
FOX II T HD 4K User Guide at www.extron.com.
100-240V ~ 0.5A MAX
50-60 Hz
INPUTS
HDMI LOOP THRU
AUDIO
LR
AUDIO
RETURN OUT
LR
RS-232 IR
Tx Rx Tx RxG
REMOTE
RS-232
Tx Rx G1 2
Step 2 — Input and Output Connections
a. Connect an HDMI video source to the HDMI input connector.
b. If desired, connect an HDMI video display to the Loop-Thru connector for a local display.
c. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector.
See the drawing below step 2d to make connections on the captive screw connector.
d. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector.
See the drawing below to make connections on the captive screw connector.
LR
Tip
ATTENTION:
• For unbalanced audio, connect the sleeves to the
ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
• Pour l’audio asymétrique, connectez les manchons au
contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
Tip
Sleeve
Tip
Sleeve
Unbalanced Stereo Input
No Ground Here
Tip
Sleeves
Tip
No Ground Here
Ring
Sleeves
Tip
Ring
Balanced Stereo Input
LR
Tip
Ring
Sleeves
Tip
Ring
ALARM
LR
LR
OVER
FIBER
LINK
Tx
OPTICAL
Rx
FOX T HD 4K
LINK
RESET
RETURN OUT
NOTE: For returned audio, above, you must also do the following:
• Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver.
• Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b.
e. If you want the FOX II units to pass serial or IR data or control signals, such as for serial
control of a projector, connect the master device to the transmitter and the slave device to the
receiver via the Over Fiber 5-pole captive screw connector.
NOTE: For returned RS-232 and IR responses (from the receiver to the transmitter, you must
install the Receiver-Tx-to-transmitter-Rx cable in step 3b.
Tx Rx Tx RxG
OVER
FIBER
RS-232 IR
Rx TxGnd
Tx RxGnd
1
FOX II T HD 4K • Setup Guide (Continued)
M
12
REMOTE
CONFIG
M
12
T
Tx
LINK
Rx
OPTICAL
LINK
f. For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two
rightmost Alarm poles of the Alarm and Remote RS-232 5-pole captive screw connector. The unit shorts both poles
together when no light is detected.
NOTE: The transmitter Alarm port reports the status of the link from the receiver.
g. For remote control of a unit and loading rmware, connect a host device, such as a computer or control system, to either of the
following ports:
Configuration port — The front panel mini USB connector.
NOTE: Extron recommends performing firmware updates via the Configuration port only.
RS-232
Tx Rx G
ALAR
Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector.
The protocol for the Remote port is as follows:
• 9600 baud • no parity • 8 data bits
• 1 stop bit • no ow control
Step 3 — Throughput Connections
NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter to a compatible receiver
in one of two ways:
• One way (transmitter to receiver) only, perform step 3a.
• Two way (transmitter to receiver and return), perform steps 3a and 3b.
a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver (
b. If you want the receiver to return serial data (such as responses from a controlled device) to the transmitter, connect
a cable between the Tx port on the receiver and Rx port on the transmitter (2).
Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).
NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.
, at right).
1
REMOTE
RS-232
ransmitter
Receiver
ALAR
Tx Rx G
LINK
OPTICAL
112222
11
Tx
Rx
LINK
2
Loading...