Extron electronics DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 231, DTP T MK 4K 331 User Manual

Download

Page 1

DTP T EU 4K 331 DTP T EU 4K 231 DTP T MK 4K 331 DTP T MK 4K 231

Digital Twisted Pair Transmitters for Extron Flex55, EU- & MK- type junction boxes

User Guide

DTP Systems

68-2962-01 Rev. B

03 17

Page 2

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide, part number 68-290-01, on the Extron website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung, EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer 68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y mantenimiento recogidas en la documentación proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento de normativas, compatibilidad electromagnética, accesibilidad y temas relacionados, consulte la Guía de cumplimiento de normativas y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une tension électrique dangereuse susceptible de provoquer un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVISO: Questo simbolo, ,quando viene utilizzato il prodotto, serve

ad avvisare l’utente della presenza di tensioni pericolose non isolate all’interno del prodotto, che può presentare un rischio di scosse elettriche.

ATTENTZIONE: Questo simbolo, , quando viene utilizzato il

prodotto, serve ad avvisare l’utente di importanti istruzioni di uso e manutenzione (assistenza) nella letteratura fornita con l’apparecchiatura.

Per informazioni sulle linee guida di sicurezza, adempimenti normativi, compatibilità EMI/EMF, accessibilità e argomenti correlati, vedere la sicurezza di Extron e Regulatory Compliance Guide, parte numero 68-290-01, sul sito Web Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии неизолированного опасного напряжения внутри корпуса продукта, которое может привести к поражению электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций по эксплуатации и обслуживанию в руководстве, прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности, соблюдении нормативных требований, электромагнитной совместимости (ЭМП/ЭДС), возможности доступа и других вопросах см. руководство по безопасности и соблюдению нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01

。

Page 3

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手冊》，準則編號 68-290-01。

安全上のご注意

• 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守( 整備)の指示についてユーザーの注意を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目については、エクストロンのウェブサイト www.extron.com より『 Extron Safety and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을 경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.

니다.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of RGBSystems, Inc. or Extron Electronics (see the current list of trademarks on the

AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, GlobalViewer, Global Configurator, Global Scripter, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VoiceLift, VN-Matrix, WallVault, WindoWall, XTP, and XTP Systems

(SM)

Registered Service Mark

AAP, AFL (Accu-RATE Frame Lock), ADSP - Advanced Digital Sync Processing, Auto-Image, CableCover, CDRS - Class D Ripple Suppression, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), eLink, Entwine, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP, QS-FPC QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, ShareLink, SIS (Simple Instruction Set), Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K, WebShare, XTRA, ZipCaddy, and ZipClip

: S3 Service Support Solutions

Registered Trademarks

Trademarks

(®)

(™)

Page 4

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

ATTENTION:

• The Twisted Pair Extension technology works with shielded twisted pair (STP)

cables only. To ensure FCC Class A and CE compliance, STP cables and STP connectors are also required.

• La technologie extension paires torsadées fonctionne avec les câbles paires

torsadées blindées(UTP) ou non blindées(STP) uniquement. Aﬁn de s’assurer de la compatibilité entre FCC ClasseA et CE, les câbles STP et les connecteurs STP sont nécessaires.

• For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron Website.

• Pour plus d'informations sur les directives de sécurité, les conformités de

régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le «Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

Page 5

Contents

Introduction ...................................................1

About this Guide ................................................. 1

About the Transmitters ....................................... 1

Features ............................................................. 3

Installation and Operation ........................... 4

Installation Overview ........................................... 4

Installing the Junction Box or European Cable

Channel System ................................................ 6

Installation Features ............................................ 7

Connection and Wiring Details ........................ 8

Mounting the Transmitter .................................. 12

Mounting an EU transmitter in a Raceway

Using Spacers (Optional) ............................. 13

Removing the Transmitter (Accessing the

Side and Rear Features) .............................. 14

Front Panel Connection .................................... 15

Operation ......................................................... 15

Indications .................................................... 15

Troubleshooting — If no Image Appears ........... 15

vDTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Contents

Page 6

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Contents vi

Page 7

Introduction

• About this Guide

• About the Transmitters

• Features

About this Guide

This guide describes the following wallplate-mounted transmitter models:

• DTP T EU 4K 331

• DTP T EU 4K 231

• DTP T MK 4K 331

• DTP T MK 4K 231

NOTE: In this guide:

• The units are commonly referred to as “transmitters.”

• Unless speciﬁcally identiﬁed by the model name, the discussions in the guide apply

to any model.

The transmitters output a signal to a compatible DTP receiver. This guide describes how to install, operate, and configure the transmitter.

About the Transmitters

The transmitters covered in this guide are HDMI transmitters with DTP outputs (see

figure 1, on the next page). The transmitters are HDCP compliant, and support resolutions

up to 4k at 30 Hz with color space 4:4:4 or 4:2:2 and 4k at 60 Hz with color space 4:2:0.

Each transmitter converts one HDMI input, including embedded audio (or DVI video with the appropriate adapter) to a proprietary digital signal. The transmitter and a compatible DTP receiver extend the usable distance of video, audio, and control signals over a single Extron XTP DTP 24 shielded twisted pair (STP) cable (recommended) or other STP cable.

The DTP T EU 4K 331 and DTP T MK 4K 331 are compatible with a DTP HDMI 330 Rx or DTP DVI 330 Rx receiver, with a range of up 330 feet (100 meters).

The DTP T EU 4K 231 and DTP T MK 4K 231 are compatible with a DTP HDMI 230 Rx or DTP DVI 230 Rx receiver, with a range of up 230 feet (70 meters).

The units consist of a device module that snaps into a plastic bezel faceplate. The transmitters in the appropriate bezels fit into EU or MK one-gang junction boxes or European cable channel systems, depending on the transmitter model. The products are also compatible with the Extron Flex55 mounting system.

In most applications, a compatible receiver can power the transmitter through the STP cable. An optional 12 VDC power supply can power the unit locally

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Introduction 1

Page 8

Display

RS-232 HDMI

SIG LINK

POWER 12V

0.7A MAX

DTP IN

OUTPUTS

DTP CROSSPOINT 84 4K

100-240V ~ 1.6 A MAX

INPUTS

50-60 Hz

DTP HDMI 330 Rx

OUTPUTS

AUDIO

Extron DTP HDMI 4K 230 Rx

OVER DTP

RS-232

TxRx Tx RxG

Receiver

CATx Cable up to 230' (70 m)

2 3A 4A

1 2 3 4 5 6

HDBT

SIG LINK

XTP

DTP

OUT

Display

RS-232 HDMI

SIG LINK

POWER 12V

0.7A MAX

DTP IN

CATx Cable up to 330' (100 m)

RS-232 IR

OVER TP

4B 4

SIG LINK

OUT

SIG LINK

XTP

DTP

Tx Rx Tx RxG

RS-232 IR

Tx Rx Tx Rx

Extron TLP Pro 1020T

10" Ta bletop TouchLink Pro Touchpanel

Doc

Tuner

1 2 3

VCRLaptop PC DVD

Cam

Tuner

321

654

987

Enter

December 15, 2013 - 7:58 AM

LAN 1

LAN 2 LAN 3

+48V

Volume

Channel

Presets

Mute

Last

Presets

System

Audio Control

Off

Ethernet

MIC/LINE

AMP OUTPUT

CLASS 2 WIRING

LR4LR

AUDIO OUTPUTS

8Ω / 4Ω

Display

Off

Mute

Room Control

Screen

Lighting

Help

OUTPUTS

DTP HDMI 330 Rx

AUDIO

Extron DTP HDMI 4K 330 Rx

OVER DTP

RS-232

TxRx Tx RxG

Receiver

Outputs

Control

Network

COM 1 COM 3COM 2 DIGITAL I/O

Tx Rx G Tx Rx G1234G

Tx Rx

RTSCTS

RESET

REMOTE

TxRx G

SIG LINK

DTP

S/PDIF

OUT

XTP

DTP

HDBT

RS-232 IR

OVER TP

RS-232 IR

Tx Rx Tx RxG

IR/SERIAL RELAYS DIGITAL I/O

CONTROL

SGSG

XTP

LINK

AUDIO INPUTS

DMP EXPANSION

EXP

34C+V

PWR OUT = 6W

LR4LR

+V D-S+S

Extron

Scaling Presentation Matrix Switcher

CATx Cable up to 330'

HDMI IN

(100 m)

Extron DTP T EU 4K 331

DTP Transmitter for EU-type Junction Boxes

CATx Cable up to 330'

HDMI IN

(100 m)

Extron DTP T MK 4K 331

DTP Transmitter for MK-type Junction Boxes

Microphones

DTP CrossPoint 84 4K IPCP SA

Audio

Audi

Extron Extron

Extron SM 26

Surface Mount Speakers

Inputs

Figure 1. Typical Transmitter Application

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Introduction 2

Page 9

Features

• Transmits HDMI up to 330 feet (100 meters) (DTP T EU 4K 331 or

DTP T MK 4K 331) or 230 feet (70 meters) (DTP T EU 4K 231 or DTP T MK 4K 231) over a single STP cable — The units provides high reliability and

maximum performance on an economical and easily installed cable infrastructure.

• Supports resolutions up to 4k30 with color space 4:4:4 or 4:2:2 and 4k60 with

color space 4:2:0

• The DTP output is compatible with HDBaseT-enabled devices — The DTP output

can be configured to send video and embedded audio to HDBaseT-enabled displays.

• Remotely powered by receiver — For simplified installation, only one power supply is

necessary to power both devices.

• Compatible with all DTP HDMI 330 (230) and DTP DVI 330 (230) receivers, and

DTP 330- (230-)enabled products — The transmitters can be used with the Extron IN1608, DTP CrossPoint 84, and other DTP 330- (230-)enabled products to meet application requirements.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Introduction 3

Page 10

Installation and Operation

This section contains information for mounting, connecting, and operating the DTP T EU 4K 331, DTP T MK 4K 331, DTP T EU 4K 231, and DTP T MK 4K 231. Topics in this section include:

• Installation Overview

• Installing the Junction Box or European Cable Channel System

• Installation Features

• Mounting the Transmitter

• Front Panel Connection

• Operation

• Troubleshooting — If no Image Appears

Installation Overview

All models can mount into junction boxes. The EU units mount into European junction boxes and the MK units mount into MK junction boxes.

The DTP T EU 4K 331 and DTP T EU 4K 231 can mount into a European cable channel system (also known as a “trunking system”). The products are also compatible with the Extron Flex55 mounting options (see www.extron.com).

To mount and connect the transmitters, consider the following:

 Ensure there is enough space between the rear panel and the back of the junction box

or European cable channel system to ﬁt connectors. Figure 2, on the next page, shows the dimensions of all transmitter models. The depth of all four transmitters is the same. Allow at least 47 mm (1.9") in the junction box for the device plus cable clearance.

NOTE: The depth of the junction box or European cable channel system may vary.

 If you are using a European cable channel system with a DTP T EU 4K 331 or

DTP T EU 4K 231, ensure the transmitter ﬁts in the desired channel.

 If necessary, prepare the mounting surface.

CAUTION: Failure to check the items listed below may result in personal injury or

property damage.

ATTENTION : La non-vériﬁcation des éléments listés ci-dessous peut provoquer

des blessures ou dommages matériels.

 Ensure there are no utility cables or pipes at the intended location that might be

damaged or cause injury when installing the device.

 Check that the installation meets the building, electrical, and safety codes.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 4

Page 11

(38.41 mm)

MK Unit, Front

MK Unit, Side

3.169"

(80.50 mm)

3.386"

6.00 mm)

2.165"

(55.00 mm)

3.169"

(80.50 mm)

EU Unit, Front

2.165"

(55.00 mm)

2.165"

(55.00 mm)

2.165"

(55.00 mm)

0.398"

(10.10 mm)

(38.41 mm)

EU Unit, Side

0.394"

(10.00 mm)

1.800"

(45.72 mm)

Front, With Bezel

1.521"

Device Module

1.800"

(45.72 mm)

1.800"

(45.72 mm)

POWER

12V

0.7 A MAX

1.800"

(45.72 mm)

3.386"

(86.00 mm)

1.521"

(38.41 mm)

1.521"

Either Unit, Rear

Figure 2. Dimensions

 Choose a location that allows cable runs without interference.

NOTE: Cables may need to be installed in the wall or conduits before the unit is

installed.

 Install the junction box or European cable channel system (see Installing the Junction

Box or European Cable Channel System on page 6).

NOTE: Refer to the manufacturer for more junction box installation requirements.

 Route and connect cables to the rear panel connectors (see Installation Features on

page 7).

 Mount the unit into the junction box (see Mounting the Transmitter on page 12).

 Connect input to the front panel connector (see Front Panel Connection on page 15).

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 5

Page 12

Installing the Junction Box or European Cable Channel System

Refer to the junction box or European cable channel system manufacturer for additional installation considerations. If required to cut an opening in the mounting surface, consider the following:

• For accuracy, use a template or the mounting enclosure to mark cut guidelines.

• To avoid making the hole too big, cut inside the marked guidelines.

CAUTION: Smooth the edges of the opening to avoid personal injury during

installation and damage to the mounting device or the cables.

ATTENTION :

l’installation et d’endommager l’appareil de montage ou les câbles.

• Secure cables with clamps or ties to provide strain relief.

• Trim back and insulate shields with heat shrink.

ATTENTION:

• To prevent short circuits, the outer foil shield can be cut back to the point

where the cable exits the cable clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

• Aﬁn d’éviter les court circuits, le blindage en aluminium extérieur peut être

réduit jusqu’à ce que le câble sorte de la cosse de câble. Le blindage tressé et le blindage en aluminium devraient être connectés à la masse d’un équipement à l’autre bout du câble.

Limez les bords de l’ouverture aﬁn d’éviter toute blessure lors de

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 6

Page 13

Installation Features

RearFront

DTP

HDTP

DTP

HDBT

Top

BD D

POWER 12V

HDMI IN

0.7 A MAX

Side

Figure 3. Installation Features

TP function switch (see below)

TP port (see page 8)

Power connector (see page 8)

Electrostatic ground point — Use the included grounding strap to ground the unit.

NOTE: This ground eliminates electrostatic discharge only. This is not an electrical

safety ground.

HDMI input port (see Front Panel Connection on page 15)

TP function switch — If the receiving device is in the Extron DTP series, use a

stylus or other tapered object to set this recessed switch to the DTP position. For an HDBaseT-enabled receiver type, set this switch to the HDBT position. This switch tailors the output signal as follows:

ATTENTION:

• Position this switch BEFORE connecting the appropriate device to the TP

connector. Failure to comply can damage the endpoint.

• Positionnez le sélecteur AVANT de connecter l’appareil approprié au

connecteur TP. Ne pas respecter cette procédure pourrait endommager le point de connexion.

HDBT position — The TP output consists of HDMI with embedded audio.

DTP position — The TP output consists of HDMI with embedded audio and remote

power.

NOTES:

• When the switch is in the HDBT position, the transmitter and receiver each

requires a local 12 VDC power supply.

• When the switch is in the DTP position, one 12 VDC power supply,

connected to either the transmitter or the receiver, can power both units.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 7

Page 14

TP port (see figure 3 on the previous page) — Plug one end of a TP cable

0.7 A MAX

Side

Pair Wires

Pins:

Connector

into this RJ-45 female jack. Plug the opposite end into the DTP Input RJ-45 port on a compatible receiver (see “TP Cable Termination and Recommendations” to wire the RJ-45 connector and for detailed NOTES).

Signal (green) LED — Lights when the transmitter outputs a video signal.

Link (yellow) LED — Lights when a device is connected and communicating.

ATTENTION:

• Do not connect this connector to a computer data or telecommunications

network.

• Ne connectez pas ces port à des données informatiques ou à un réseau de

télécommunications.

Power connector — When the TP function switch is in the DTP position, this

connector is probably not necessary. The connected receiving device can remotely power the transmitter via the TP cable.

POWER 12V

ATTENTION:

• Remote power is intended for indoors use only. No part of a network that uses

remote power can be routed outdoors.

• L’alimentation à distance est exclusivement réservée à un usage en intérieur.

Un réseau utilisant une alimentation à distance ne peut pas être routé en extérieur.

If the TP function switch (item A on the previous page) is in the HDBT position, or if otherwise desired, plug an optional external 12 VDC power supply into this 2-pole direct insertion connector (see Power Supply Wiring on page 10).

NOTE: When the TP function switch is in the DTP position, one power supply

can power both units.

When the TP function switch is in the HDBT position, the transmitter and receiver each requires a local 12 VDC power supply.

HDMI input port (see Front Panel Connection on page 15)

Connection and Wiring Details

TP Cable Termination and Recommendations

Figure 4 details the TIA/EIA-T568B wiring standard. Use this standard to terminate the DTP cable with RJ-45 connectors.

Figure 4. TP Cable Termination

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 8

12345678

Insert

Twisted

White-orange

Orange

2 3

White-green

Blue

White-blue

Green

White-brown

Brown

RJ-45

TIA/EIA T

568 B

Wire color

Page 15

NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

cable to link the transmitter and receiver. The DTP T EU and DTP T MK units do not work properly with these cables.

Supported cables

The DTP units are compatible with shielded twisted pair (STP) and unshielded twisted pair (U/UTP) cable. However, Extron strongly recommends that you use STP cable to achieve best performance.

ATTENTION:

• To ensure FCC Class A and CE compliance, STP cables and STP connectors are

required.

• Aﬁn de s’assurer de la compatibilité entre FCC ClasseA et CE, les câbles STP et

les connecteurs STP sont nécessaires.

Cable recommendations

Extron recommends using the following practices to achieve full transmission distances up to 330 feet (100 meters) (DTP T EU 4K 331 and DTP T MK 4K 331) or 230 feet (70 meters) (DTP T EU 4K 231 and DTP T MK 4K 231) and reduce transmission errors.

• Use the following Extron XTP DTP 24 STP cables and DTP 24 connectors for the best

performance:

• XTP DTP 24/1000 Non-Plenum 1000’ (305 meters) spool 22-236-03

• XTP DTP 24P/1000 Plenum 1000’ (305 meters) spool 22-235-03

• XTP DTP 24 Plug Package of 10 101-005-02

• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid

conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard.

• Use no more than two pass-through points, which may include patch points, punch

down connectors, couplers, and power injectors. If these pass-through points are required, use CAT 6 or 6a shielded couplers and punch down connectors.

NOTE: When using STP cable in bundles or conduits, consider the following:

• Do not exceed 40% ﬁll capacity in conduits.

• Do not comb the cable for the ﬁrst 20 meters, where cables are straightened,

aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 9

Page 16

Power Supply Wiring

Power Supply

Output Cord

Direct Insertion

Connector

SECTION A–A

Ridges

Smooth

1.0 A MAX

12V

0.7 A MAX

POWER 12V

NOTE: The transmitter normally receives power from the receiver. A power supply is not

included with the transmitter. This section is for wiring an optional power supply.

Figure 5 shows how to wire the connector.

Figure 5. Power Connector Wiring

CAUTION: ATTENTION :

• The wires must be kept separate while the power supply is plugged in. Remove

power before wiring.

• Les deux cordons d’alimentation doivent être maintenus séparés lorsque la

source d’alimentation est branchée. Coupez l’alimentation avant d’effectuer un raccordement.

• The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

• Any longer and the exposed wires may touch, causing a short circuit between

them.

• Any shorter and the wires can be easily pulled out even if tightly fastened by the

captive screws.

• La longueur des câbles exposés est importante. La longueur idéale est de 5mm

(3/16inches).

• S’ils sont trop longs, les câbles exposés pourraient se toucher et provoquer un

court-circuit.

• S’ils sont trop courts, ils peuvent être tirés facilement, même s’ils sont

correctement serrés par les borniers à vis.

• Do not tin the power supply leads before installing them in the connector. Tinned

wires are not as secure in the connector and could be pulled out.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles

étamés ne sont pas aussi bien ﬁxés dans le connecteur et pourraient être retirés.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 10

Page 17

ATTENTION:

• If not provided with a power supply, this product is intended to be supplied by a UL

Listed power source marked “Class 2” or “LPS” and rated output 12V dc, minimum

1.0 A minimum. Always use a power supply supplied by or speciﬁed by Extron. Use of an unauthorized power supply voids all regulatory compliance certiﬁcation and may cause damage to the supply and the end product.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté

par une source d’alimentation certiﬁé UL de classe 2 ou LPS, avec une tension nominale 12 Vcc, 1 A minimum. Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source d’alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que le produit ﬁnal.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling

spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation

dans les espaces d’aération ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently ﬁxed to a building structure or similar structure.

• Cette installation doit toujours conforme aux dispositions applicables du Code

américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie1, section16. La source d’alimentation ne devra pas être ﬁxée de façon permanente à une structure de bâtiment ou à une structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the

power supply and the unit. The ridges on the side of the cord (see ﬁgure 5 on the previous page) identify the power cord negative lead.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du cordon (voir l’illustration 5 sur la page 10) permettent de repérer le pôle négatif du cordon d’alimentation.

To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 11

Page 18

Mounting the Transmitter

EU MountingMK Mounting

ATTENTION:

• Ensure that the junction box is grounded properly.

• Assurez vous que le boîtier d’encastrement est correctement mis à la terre.

Mount the transmitter to a junction box as follows:

1. Disconnect power from all devices at the source.

2. Orient the mounting bracket as appropriate for your transmitter (see figure 6):

• MK mounting — The word “Front” engraved on the bracket reads vertically.

• EU mounting — “Front” reads horizontally.

MK Wall Box

EU Wall Box

EU Mounting Bracket

MK Mounting Bracket

Figure 6. Mounting the Transmitter to a Junction Box

3. Fasten the provided metal mounting bracket to the mounted junction box, in the proper

orientation, using the two included screws.

NOTES:

• To keep the transmitter securely in place and prevent it from being easily pulled

from its mounting surface, ensure that the side of the bracket with the word “Front” engraved on it faces out (away from the junction box).

• If you want to be able to remove the transmitter easily from its mounting, attach

the mounting bracket with “Front” facing inward, toward the junction box.

4. Run the TP cable and optional power cable through the junction box and the plastic

bezel frame.

5. Set the TP function switch to the appropriate position (see item A on page 7).

6. Connect the rear panel cables to the transmitter.

7. Align the bezel frame to the metal mounting bracket on the mounting surface.

8. Holding the bezel frame in place on the bracket, press the transmitter into the frame

until the unit snaps into place and all four tabs on the unit snap into their slots.

Bezel Frame

DTP T EU

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 12

Page 19

Mounting an EU transmitter in a Raceway Using Spacers (Optional)

Mounting Bra

Raceway

If the EU transmitter does not stay in place when installed in a cable raceway, this may be due to a gap between the metal mounting bracket and the bezel frame. When this gap exists, the tabs on the sides of the transmitter do not reach the metal mounting bracket and the transmitter does not snap completely into the mounting bracket.

You can fix this problem by installing a spacer (provided with the EU transmitter) between the metal mounting bracket and the rim of the junction box. This spacer is engraved with the words “Optional Spacer” and “Place behind bracket” and has a slightly larger center opening than the mounting bracket.

NOTE: Do not attempt to use the spacer in place of the metal mounting bracket.

Because of its larger opening, the spacer cannot hold the EU transmitter in place.

To mount the transmitter EU to a raceway using the spacer:

1. Disconnect power from all devices at the source.

2. Mount the junction box in the raceway.

3. Attach the spacer to the junction box using two of the included screws in the holes

at the sides of the spacer. Leave the screw heads protruding approximately 1/8 inch (3.175 mm) from the surface of the spacer (see figure 7).

Junction Box

cket

Spacer

unction Box

Spacer

Metal Bracket

Bezel Frame

Cable Raceway

Figure 7. Mounting the EU Transmitter Using a Spacer

4. With the “Front” marking toward you (away from the spacer and junction box), place the

metal mounting bracket onto the spacer so that the screw heads pass through two of the slotted holes in opposite sides of the bracket.

5. Rotate the mounting bracket as necessary to ensure that the transmitter will be

positioned straight on the mounting surface and not skewed to either side.

6. Tighten the screws to secure the bracket to the spacer.

7. Pull the TP cable and optional power cable through the junction box and the plastic

bezel frame and connect them to the transmitter.

8. Align the bezel frame with the metal mounting bracket on the mounting surface.

9. Press the transmitter into the frame until the unit snaps into place.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 13

DTP T EU

Page 20

Removing the Transmitter (Accessing the Side and Rear Features)

To access the transmitter side and rear panel features after the transmitter has been mounted, you must use a removal tool (included, shown at right) to remove the transmitter from the installation surface.

Remove the transmitter from the mounting surface as follows:

1. Insert the flat tip of the removal tool in the center of the right or left edge of the

transmitter, between the unit and the wall frame, all the way to the line below the arrow on the tool (see figure 8).

Extron

Insert to lin

Figure 8. Inserting the Removal Tool in a Transmitter

2. Gently press the removal tool either inward or outward to release the tab holding the

transmitter in place in the wall frame.

3. If the transmitter does not immediately come free of the bezel frame, pry the unit

outward (away from the wall) until it is free of the installation surface, then lift it out, leaving the metal mounting bracket attached.

NOTE: Without the transmitter to hold the bezel frame in place, the frame is also

removed.)

To reinstall the transmitter, hold the bezel frame in place on the bracket and press the transmitter into the frame until the unit snaps into place and all four tabs on the unit snap into their slots.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 14

Page 21

Front Panel Connection

B A

HDMI IN

Figure 9. Front Panel HDMI Connection and Indicator

HDMI IN

HDMI input port — Connect a digital video source to the transmitter via

this HDMI connector. It accepts HDMI, and can also accept a DVI or dual mode DisplayPort video source with an appropriate adapter.

NOTE: The maximum HDMI cable length is 4.5 m (15 feet).

Operation

Plug in all system components and turn on the input device (such as a Blu-Ray player or computer) and the output device. Set the input devices to output video using the operating instructions of that device. The image should appear on the screen. If no image appears, see “Troubleshooting — If no Image Appears,” below.

Indications

Power ( ) LED — Lights to indicate power and signal status:

Amber — The transmitter is receiving power from either the connected DTP receiver or a local power supply. No digital video signal is input.

Green — The transmitter is receiving power and is detecting TMDS on the HDMI input connector.

Troubleshooting — If no Image Appears

1. Ensure that all devices are plugged in and powered on.

2. Ensure an active input is applied to the transmitter. The transmitter is receiving an active

input if the power LED is lit green.

3. Ensure that the proper signal format is supplied.

4. Check the cabling and make corrections as necessary.

5. Call the Extron S3 Sales & Technical Support Hotline if necessary. See the end of this

guide for the phone number in your region of the world.

DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, and DTP T MK 4K 231 • Installation and Operation 15

Page 22

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Extron Electronics 1230 South Lewis Street Anaheim, CA 92805 U.S.A.

Europe and Africa:

Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands

Japan:

Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan

China:

Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China

Asia:

Extron Asia Pte Ltd 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363

Middle East:

Extron Middle East Dubai Airport Free Zone F13, PO Box 293666 United Arab Emirates, Dubai

Singapore

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modiﬁcations were made to the product that were not authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040 Asia: 65.6383.4400 Japan: 81.3.3511.7655

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or ﬁtness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673 (Inside Europe Only)

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+65.6383.4400 +65.6383.4664 FAX

Extron Japan

+81.3.3511.7655 +81.3.3511.7656 FAX

Extron China

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800 +971.4.299.1880 FAX

Extron Australia

+61.8.8113.6800 +61.8.8351.2511 FAX

Extron India

1800.3070.3777 (Inside India Only)

+91.80.3055.3777 +91.80.3055.3737 FAX