Page 1
IMPORTANT:
complete user guide
instructions, and specifications.
V
Go to www.extron.com for the
DTP T DWP 4K D Series • Setup Guide
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP T DWP 4K D series of
twisted pair (TP) wallplate extenders.
OUTPUTS
AUDIO IN
AUDIO IN
HDMI IN
DP IN
Extron
Extron
DTP T DWP 4K 232 D Tx
Transmitter
1 2 3 4 5 6 7 8
CONFIG
Extron
1
CONFIGURABLE
100-240V ~ -- A MAX
2
50/60 Hz
IN1608
XTP DTP 24 Cable
230'
INPUTS
INPUTS
5
3
7
SIG LINK
HDMI
HDMI
6
4
DTP IN
INPUTS
MENU
SIGNAL
1
2 3 4 5 6 7 8 A B C
HDCP
IN1608 SA
OUTPUTS
OVER DTP
RS-232 IR
TxRx TxRxG
OVER DTP
RS-232 IR
TxRx TxRxG
LL1R R
C
A
8
SIG LINK
SIG LINK
OVER DTP
HDMI
L2
L4
R
RS-232 IR
B
DTP OUT
TxRx TxRxG
DTP IN
ENTER
SCALING PRESENTATION SWITCHER
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
AUDIO INPUTS
OUTPUTS
L5R
12
+48V
MIC/LINE
VARIABLE
RESET
L6
LR
R
R
2
+48V
VOLUME
IN1608
L3R
CLASS 2 WIRING
REMOTE
IPCP 505
LAN
RS-232
TxRx
G
COM
SWITCHED
12VDC
LIMIT
2
R
TXRXTX
12345678
314
OVER
IPCP 505
SIG LINK
POWER
12V
0.7A MAX
DTP IN
DTP HDMI 230 Rx
RTS
IR/S
CTS
4
RX
5162738
Ethernet
OUTPUTS
RELAY
5162314
LR
FLEX
100
eBUS
I/O
2
4
ACT LIMIT
OVER
738
Network
LINK
IR
ACT
TLP 1000T
AUDIO
HDMI
Projector
, installation
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Wall opening is
flush with edge of box.
Wall Stud
Screws or
Nails
Step 2 — Prepare the Mounting Surface
ATTENTION:
• Installation and service must be performed by
authorized personnel.
• L’installation et l’entretien doivent être effectués par le
personnel autorisé uniquement.
• The unit must be installed in accordance with the
National Electrical Code and with local electrical and
safety codes.
• L’unité doit être installée conformément au National
Electric Code et aux normes électriques et de sécurité
locales.
NOTE: Use a UL-listed junction box with a depth of at least 3.0 inches (7.6 cm). Alternatively, the included mud ring (MR
200) can be used. For more information, see the full product user guide at www.extron.com.
a. Place the junction box against the installation surface and mark the opening guidelines.
Cable
Clamp
Signal Output
Cable
AUTO SW
HDCP
HDBT
DTP
1
AUDIO IN
CONFIG
HDMI IN
Extron
DTP T DWP 4K 332 D
Decorator-Style Faceplate
AUDIO IN
DP IN
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Secure the junction box to the wall stud with 10-penny nails, #8 screws, or #10 screws, leaving the front edge ush with the
surface.
d. Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.
TIP: In order to t the unit in the junction box, do not install boots on TP cables and RJ-45 connectors.
1
Page 2
DTP T DWP 4K D Series • Setup Guide (Continued)
Connected RS-232 and
OVER TP
F
DTP T DWP 4K D Rear Panel
DTP T DWP 4K D Side Panel
A
B
RS-232
t
Step 3 — Connect Inputs to the Extender
Front panel
Audio input connectors — Connect an unbalanced stereo audio
A
source to this 3.5 mm mini stereo jack.
HDMI input connector — Connect an HDMI cable between this port
B
and the output port of the digital video source.
DisplayPort input connector — Connect a DisplayPort cable
C
between this port and the output port of the video source.
Mini USB port — Connect a male USB mini-B cable to this port for
D
SIS configuration and firmware updates.
AUDIO IN
HDMI IN
AUTO SW
HDCP
1
2
CONFIG
AUDIO IN
A
DP IN
C
D
Rear panel
Extron
G
1.1 A MAX
12V
POWER
HDBT
DTP
RESET
DTP T DWP 4K 232 D
A
OVER TP REMOTE
Tx Rx Tx Rx G Tx Rx G
IR
RS-232 RS-232 SIG LINK
B
C
OUT
D
E
DC power input connector — Wire and plug the included external 12 VDC power supply into either this 2-pole connector or
A
the power input connector on the receiver (see the DTP T DWP 4K 232/332 D User Guide at
www.extron.com for wiring information).
Over TP connector — Connect an RS-232 device, IR device, or both to this 5-pole, 3.5 mm captive screw connector for
B
bidirectional pass-through device control. Wire the connector as shown in the diagram below. The Ground pin is shared by
both devices.
IR Device Pins
RxTx
G
RxTx
RS-232 IR
Receive pin for IR control
Transmit pin for IR control
Ground
Receive pin on connected unit
Transmit pin on connected unit
DTP T DWP 4K D Front Panel
DC power input connector
A
Over TP connector
B
Remote connector
C
Ground port
D
DTP Out connector (page 3)
E
Reset button (page 3)
F
DTP/HDBaseT switch (page 3)
G
• RS-232 — Connect an RS-232 device and congure it as follows: 9600 baud rate, 8 data bits,1 stop bit, no parity.
• IR — Bidirectional TTL level (0 to 5 V) modulated infrared from 30 kHz to 60 kHz.
Remote connector — Connect an RS-232 device to this 3-pole, 3.5 mm captive screw connector for SIS configuration and
C
firmware updates. Wire the cable as shown in the diagram below.
Ground
Tx Rx G
Receive pin on connected unit
Transmit pin on connected uni
Ground port — Use the included grounding strap to ground the unit to a junction box or other grounding point.
D
2
Page 3
DTP Out connector — Connect one end of a twisted pair cable to this RJ-45 connector and the opposite end to a
TP Wires
Pins:
E
compatible receiving device.
ATTENTION:
• Do not connect this output to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
Reset button — Use an Extron Tweeker or small screwdriver to press and hold the recessed button while cycling power to
F
the extender to perform a factory reset.
DTP/HDBaseT switch — Set this 2-position, recessed switch to configure the output between HDBaseT and DTP modes.
G
When configured for HDBaseT, use an HDBaseT-compatible receiving device. When configured for DTP, use a DTPcompatible receiving device.
NOTES:
• When the switch is set to DTP mode, remote power is available and a single power supply connected to either
a extender or compatible receiver can power both units.
• When the switch is set to HDBaseT mode, remote power is disabled and power supplies are required for both
extender and a receiving device. Analog audio is enabled, but incompatible with third-party HDBaseT devices.
Step 4 — Run Cables Between Units
12345678
Connect the rear panel extender output to a rear panel receiving device input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
• RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B wiring
standard for all connections. For more information on TP cable wiring and termination, see the full
product user guides at www.extron.com.
• Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
TIA/EIA
T568-B
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the device with
DTP extenders or receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
• Use shielded RJ-45 plugs to terminate the cable.
• Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches used. If
possible, limit the number of patches to two total.
• If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 5 — Connect the Outputs from a Compatible Receiver
a. Connect an HDMI or DisplayPort cable (depending on your receiving device type) between the receiving device output port
and the input port of the display.
b. Connect a stereo audio device to the 3.5 mm mini stereo jack to receive the passed-through unbalanced audio.
c. Plug an RS-232 or modulated IR device into the RS-232/IR pass-through port.
Step 6 — Power the Units
The units can be powered one of two ways:
• Locally with the included power supply. A compatible receiving device can be powered remotely through the DTP line.
• Remotely via the DTP line by a locally powered DTP 230 or 330 compatible device.
NOTE: See notes in G above for remote power restrictions.
3
Page 4
Step 7 — Final Installation
A
C
a. Make all connections, power the units, and test the system for satisfactory operation.
b. At the power outlet, unplug the power supply.
c. Mount the extender into the wall box, and attach the supplied decorator-style faceplate to the unit.
d. At the power outlet, reconnect the power supply. This powers up both units.
Operation
NOTE: Input switching can be performed via auto switching, RS-232, or IR through the rear panel connectors.
After all devices are powered up, the system is fully operational.
AUDIO IN
HDMI IN
Extron
AUTO SW
HDCP
1
2
CONFIG
AUDIO IN
DP IN
A
B
Extender LEDs
LEDs — These two-color front panel LEDs on the extenders light to indicate signal and power status as follows:
A
• Amber — The unit is receiving power but there is no signal on the associated input.
• Green — The unit is receiving power and a signal is present on the associated input.
Switch LED — Lights green when auto switch is active.
B
LEDs — Light green when an HDMI or DisplayPort input has been authenticated on the source device.
C
Audio Configuration
The DTP T DWP 4K D series can embed analog audio inputs onto the digital video output.
NOTE: If no HDMI or DisplayPort signal is present, analog audio transmitted over the DTP connection to the analog audio
output of the receiver.
When an input is selected, audio transport over HDMI or DisplayPort can be congured to operate in one of three modes. Each
input can be congured individually for any of the three modes.
• Transport digital embedded audio (default) — The digital embedded audio content on the digital video input is transported.
Analog audio is still separate from the digital embedded audio on the HDMI or DisplayPort signal and transported
simultaneously over the DTP output, not embedded onto the digital output.
• Embed analog audio input — The analog audio input is always embedded to the digital output, replacing whatever content
is already present on the digital embedded audio. Analog audio is also transported over the DTP output as a simultaneous
output.
• Auto select between analog audio and digital embedded audio — When both analog audio and digital embedded audio
on HDMI or DisplayPort are present, digital embedded audio on the HDMI or DisplayPort signal takes priority. Analog audio is
transported simultaneously with the digital embedded audio content that is already present on the DTP output.
4
© 2015 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2762-50 Rev. B
5 17
Loading...