Extron electronics DTP R HWP 4K D series Setup Manual
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP R HWP 4K D Series • Setup Guide
V
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP R HWP 4K 231 D and
DTP R HWP 4K 331 D extenders.
OUTPUTS
AUTO SW
AUDIO IN
AUDIO IN
HDCP
1
VGA IN
HDMI IN
CONFIG
IR OUT
G
S
Extron
DTP T UWP 232 D
Transmitter
AUTO SW
AUDIO IN
AUDIO IN
HDCP
HDCP
1
1
2
HDMI IN
HDMI IN
CONFIG
IR OUT
G
S
Extron
DTP T HWP 232 D
Transmitter
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
1 2 3 4 5 6 7 8
CONFIG
Extron
1
CONFIGURABLE
100-240V ~ -- A MAX
2
50/60 Hz
IN1608
XTP DTP 24 Cable
230'
INPUTS
INPUTS
5
3
7
SIG LINK
HDMI
HDMI
6
4
DTP IN
INPUTS
MENU
SIGNAL
1
2 3 4 5 6 7 8 A B C
HDCP
IN1608 SA
OUTPUTS
OVER DTP
RS-232 IR
TxRx TxRxG
OVER DTP
RS-232 IR
TxRx TxRxG
LL1R R
C
A
8
SIG LINK
SIG LINK
OVER DTP
HDMI
L2
L4
R
RS-232 IR
B
DTP OUT
TxRx TxRxG
DTP IN
VOLUME
ENTER
IN1608
SCALING PRESENTATION SWITCHER
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L3R
AUDIO INPUTS
OUTPUTS
L5R
12
CLASS 2 WIRING
REMOTE
LAN
+48V
MIC/LINE
VARIABLE
RESET
RS-232
L6
LR
R
R
2
+48V
TxRx
G
SWITCHED
R
12 VDC
21
LIMIT
TxRxTx
OVER
4312345678
COM
RTS
CTS
Rx
IPCP PRO 550
IR/SERIAL
2134
56782134
5678
Ethernet
RS-232 IR
TxRx
OVER DTP
G
TxRx
HDMI OUT
RELAYS FLEX
IPCP PRO 550
eBUS
I/O
1000
SLIMIT
2134
LINK
IR
ACT
OVER
Network
TLP 1000T
HDMI
Extron
DTP R HWP 4K 331 D
Receiver
Projector
Step 2 — Prepare the Mounting Surface
ATTENTION:
• Installation and service must be performed by authorized personnel.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• The unit must be installed in accordance with the National Electrical Code and with local electrical and safety
codes.
• L’unité doit être installée conformément au National Electric Code et aux normes électriques et de sécurité locales.
NOTE: Use the included mud ring (MR 200) or a UL approved 1-gang RACO wall box (not supplied) with a depth of at
least 3.0 inches (7.6 cm). For more information, see the full product user guide at www.extron.com.
a. Place either the mud ring (see gure on page 1) or the wall box (see gure on page 2) against the installation surface and
mark the opening guidelines.
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Either:
• Insert the mud ring into the opening, rotate the locking
arms, and secure it with the supplied screws,
or
• Secure the wall box to the wall stud with 10-penny nails
or #8 or #10 screws, leaving the front edge ush with the
surface.
Rotate locking arm
and insert into wall
opening.
Mud Ring
1
DTP R HWP D 4K Series • Setup Guide (Continued)
TP Wires
Signal
Output
Cabl
d. Run all required cables (see steps 3, 4, and 5),
thread the cables through the mud ring or walll
Wall Stud
box, and secure them with cable clamps.
TIP: In order to t the unit in the junction
box, do not install boots on TP cables
e
and RJ-45 connectors.
Screws
or Nails
Extron
DTP R HWP 4K 231 D
Step 3 — Run Cables Between Units
Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
• RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B
wiring standard for all connections. For more information on TP cable wiring and
termination, see the DTP R HWP 4K 231 and 331 D User Guide at www.extron.com.
• Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
OVER DTP
HDMI OUT
Extron
Decora Faceplate
Pins:
12345678
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
TIA/EIA
T568-B
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable to link the device with DTP transmitters or
receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
NOTE: Extron XTP DTP 24 Shielded twisted pair cable is strongly recommended for
optimal performance.
• Use shielded RJ-45 plugs to terminate the cable.
• Limit the use of RJ-45 patches. Overall transmission distance capabilities vary
depending on the number of patches used. If possible, limit the number of patches to
two total.
• If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 4 — Connect Output Device
Front Panel
A DTP RS-232 and IR connectors — To pass serial or infrared data or control signals,
such as serial control of a projector, connect the master device to the transmitter and
the slave device to the receiver via the RS-232 and IR captive screw connectors on both
units.
B HDMI output connector — Connect an HDMI cable between this port and the input on
a sink device.
2
OVER DTP
A
HDMI OUT
B
Extron
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Front Panel
Loading...