Extron electronics DTP HDMI 4K D Series, DTP HDMI 4K 230 D, DTP HDMI 4K 330 D User Manual

Download

Page 1

DTP HDMI 4K D Series

HDMI Twisted Pair Extender Transmitters and Receivers

User Guide

HDMI Extenders

68-2366-01 Rev. F

01 19

Page 2

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide, part number 68-290-01, on the Extron website, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa all’interno del contenitore del prodotto che può costituire un rischio di scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative, compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo 68-290-01, sul sito web di Extron, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung, EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer 68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y mantenimiento recogidas en la documentación proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento de normativas, compatibilidad electromagnética, accesibilidad y temas relacionados, consulte la Guía de cumplimiento de normativas y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une tension électrique dangereuse susceptible de provoquer un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии неизолированного опасного напряжения

внутри корпуса продукта, которое может привести к поражению электрическим

током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций по эксплуатации и обслуживанию в руководстве, прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности, соблюдении нормативных требований, электромагнитной совместимости (ЭМП/ЭДС), возможности доступа и других вопросах см. руководство по безопасности и соблюдению нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01

。

Page 3

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守( 整備)の指示についてユーザーの注意を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目については、エクストロンのウェブサイト www.extron.com より『 Extron Safety and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을 경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.

니다.

Page 4

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

ATTENTION: The Twisted Pair Extension technology works with unshielded twisted

pair (UTP) or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE compliance, STP cables and STP Connectors are required.

For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory

Compliance Guide” on the Extron website.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks(

ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, GlobalScripter, GlobalViewer, Hideaway, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTPSystems

Registered Service Mark

AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression), DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, Show Me, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K , VideoLounge, WebShare, XTRA, ZipCaddy, and ZipClip

(SM)

), registered service marks(

: S3 Service Support Solutions

), and trademarks(TM) are the property of RGBSystems, Inc. or

Registered Trademarks (

Trademarks (™

)

Page 5

Page 6

Introduction............................................................ 1

About this Guide ................................................. 1

About the DTP HDMI 4K D Series

Extenders .......................................................... 1

Twisted Pair Cable Advantages ....................... 2

Transmission Distance .................................... 2

Features ............................................................. 2

Installation and Operation .................................. 3

Mounting the Transmitter or Receiver .................. 3

UL and Safety Guidelines ................................ 3

Site Preparation and Wall Box Installation ....... 4

Mud Ring Installation ...................................... 5

Final Installation .............................................. 6

Transmitter Connections ..................................... 6

Transmitter Front Panel ................................... 6

Transmitter Rear Panel .................................... 7

Receiver Connections ......................................... 8

Receiver Rear Panel ....................................... 8

Receiver Front Panel ....................................... 9

Twisted Pair Recommendations for DTP

Communication ............................................... 10

Power Supply Wiring ........................................ 11

RS-232 and IR Connector Wiring ..................... 13

Operation ......................................................... 14

Transmitter Power Indicator .......................... 14

Receiver Power Indicator .............................. 14

System Operation ......................................... 14

Ground Loops .................................................. 15

Reference Information ...................................... 16

Decorator-Style Wallplate Template

Dimensions ..................................................... 16

viDTP HDMI 4K D Series Transmitter and Receiver • Contents

Page 7

Page 8

Introduction

• About this Guide

• About the DTP HDMI 4K D Series Extenders

• Features

About this Guide

This guide describes the Extron DTP HDMI 4K D Series family of High-Definition Multimedia Interface (HDMI) Extenders, which consists of DTP HDMI 4K D transmitters and DTP HDMI 4K D receivers. This guide describes how to install, operate, and configure them.

About the DTP HDMI 4K D Series Extenders

The Extron DTP HDMI 4K 230 D and DTP HDMI 4K 330 D extenders are a family of HDMI transmitters and receivers (see figure 1) which are housed in enclosures that can be mounted in Underwriters Laboratories (UL) standard wall boxes with decorator-style face plates. A transmitter and receiver pair extends the usable distance of HDMI digital video and RS-232 or IR control signals over one shielded twisted pair (STP) cable.

CATx Cable up to 230' (70 m)

Extron DTP HDMI 4K 230 D Rx

Receiver

OUTPUTS

OVER DTP

-232

G Tx Rx

TxRx

AUDIO

Flat Panel Display

RS-232

HDMI

INPUTS

OVER DTP

RS-232

TxRx G Tx Rx

AUDIO

HDMI

Blu-ray Player

Extron DTP HDMI 4K 230 D Tx

Transmitter

RS-232

100

Y ELA R

LINK

ACT

INPU

TXRX

IPL

TCP/IP

TouchLink

Control System

VCR

D DV

C DO CAM

P PTO A L

OFF

PLAY DIS MUTE

EEN SCR

WN DO

Figure 1. Typical Transmitter and Receiver Application

A DTP HDMI 4K D Series system consists of a transmitter (Tx) and a receiver (Rx). The pair can handle a single HDMI digital video signal and a bidirectional RS-232 or IR link. The DTP HDMI 4K D Series transmitters and receivers are sold separately. Each purchased transmitter is shipped with a single external desktop 12 VDC power supply that accepts 100 to 240 VAC, 50-60 Hz input. A single power supply connected to either the transmitter or the receiver can power both units through the twisted pair cable that links the units.

DTP HDMI 4K D Series Transmitter and Receiver • Introduction 1

Page 9

Twisted Pair Cable Advantages

Twisted pair (TP) cable is much smaller, lighter, more flexible, and less expensive than coaxial or HDMI cable. These transmitter and receiver TP products make cable runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple, quick, and economical (see Twisted Pair Recommendations for DTP Communication on page 10 for more information).

NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

cable to link the transmitter and receiver. The DTP HDMI 4K D Series Tx/Rx do not work properly with these cables.

Control communications

The RS-232 or infrared (IR) communications are pass-through only. The transmitter and receiver do not generate or respond to these signals.

Transmission Distance

The maximum transmission distance is determined by the resolution of the signal and the twisted pair cable, graphics card, and display used in the system.

• The DTP HDMI 4K 230 D transmitters and compatible receivers can transmit and

receive video signals of 720p, 1080i, 1080p HDTV, UHD (3840x2160) @ 30/60 Hz, or 4k (4096x2160) @ 30/60 Hz up to 230 feet (70 meters).

• The DTP HDMI 4K 330 D transmitters and compatible receivers can transmit and

receive video signals of 720p, 1080i, 1080p HDTV, UHD (3840x2160) @ 30/60 Hz, or 4k (4096x2160) @ 30/60 Hz up to 330 feet (100 meters).

Features

Transmits single link HDMI-D signals over one STP cable — Twisted pair cables provide an economical, easily installed cable solution.

Supports DDC and HDCP transmission — The DTP HDMI 4K D transmitters and receivers fully support long distance transmission of the DDC and HDCP signals.

Control communications pass-through — Bidirectional RS-232 or IR control signals can be transmitted alongside the HDMI signal, so that the remote display can be controlled without the need for additional cabling.

Audio routing — The DTP HDMI 4K D transmitters and receivers route unbalanced stereo audio.

Supports CEC signal transmission

Wall-mountable enclosures

External 100 VAC to 240 VAC, 50-60 Hz, international power supply — Included with

transmitters.

Remote powering of the transmitter or receiver — Only one power supply is necessary to power both devices.

Supports computer video up to 1920x1200, HTDV 1080p @ 60 Hz with Deep Color, UHD, and 4k resolutions.

DTP HDMI 4K D Series Transmitter and Receiver • Introduction 2

Page 10

Installation and Operation

This section describes the installation and the operation of the DTP HDMI 4K D Series, including:

• Mounting the Transmitter or Receiver

• Transmitter Connections

• Receiver Connections

• Twisted Pair Recommendations for DTP Communication

• Power Supply Wiring

• RS-232 and IR Connector Wiring

• Operation

• Ground Loops

Mounting the Transmitter or Receiver

ATTENTION:

• Installation and service must be performed by authorized personnel.

• L’installation et l’entretien doivent être effectués par le personnel autorisé

uniquement.

• The unit must be installed in accordance with the National Electrical Code and with

local electrical and safety codes.

• L’unité doit être installée conformément au National Electric Code et aux normes

électriques et de sécurité locales.

The DTP HDMI 4K D Series transmitters and receivers can be installed in a two-gang electrical wall box, or with a mud ring, with a decorator-style wallplate cover (supplied).

The installation must conform to national and local building, electrical, and safety codes and to the size requirements of the wall plate.

UL and Safety Guidelines

The following UL guidelines pertain to the installation of the decorator-style wallplate transmitters and receivers into a wall or furniture.

• These units are not to be connected to a centralized DC power source or used beyond

their rated voltage range.

• Install into a UL-listed outlet or junction box with the provided faceplate or a UL-listed

faceplate

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 3

Page 11

Site Preparation and Wall Box Installation

Wa ﬂush with edge of box.

Choose a location that allows cable runs without interference. Allow enough depth for both the wall box and the cables. Install the cables into the wall, furniture, or conduits before installing the wall plate.

NOTE: The decorator-style wallplate units are very deep and have connectors on the

back side. Extron recommends a 2-gang wall box which has a depth of at least 3.0 inches (7.6 cm) to accommodate the connectors and cables.

To install a new wall box, perform steps 1 through 9. If a suitable wall box is already installed, perform steps 6 through 9 on the next page. UL-listed wall boxes are recommended.

1. If a wall box is not available to use for a template, use the Decorator-Style Wallplate

Template Dimensions on page 16 to create a template. If installing directly into

furniture, cut out the center portion of the template.

2. Place the wall box (or the full-sized template) against the installation surface, and mark

the opening guidelines.

3. Cut out the material from the marked area.

4. Insert the wall box into the opening. The rear connectors on the box or wall plate should

fit easily into the opening. Enlarge or smooth the edges of the opening if needed.

5. Secure the wall box with nails or screws, leaving the front edge flush with the outer wall

or furniture surface (see figure 2).

NOTES:

• If attaching the wall box to wood, use four #8 or #10 screws or four 10-penny

nails. A minimum of 0.5 inch (1.3 cm) of screw thread must penetrate the wood.

• If attaching the wall box to metal studs or furniture, use four #8 or #10

self-tapping sheet metal screws or machine bolts with matching nuts.

Wall Stud

Screws or Nails

ll opening is

Cable Clamp

OVER DTP

INPUT

RS-232

TxRx TxRxG

AUDIO

Signal Output Cable

Extron DTP HDMI 4K D

Decorator-Style Faceplate

Figure 2. Installing the Wall Box and Mounting the Unit

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 4

Page 12

6. Feed the twisted pair cable and, if applicable, the power cable through the opening

and through the wall box punch-out holes, securing them with cable clamps to provide strain relief.

NOTES:

• In order to ﬁt in the wall box, the twisted pair cables and RJ-45 connectors

• One power supply can power both the transmitter and the receiver, so only

7. Trim back and insulate exposed cable shields with heat shrink to reduce the chance of

short circuits.

To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp.

8. Connect the cables to the rear of the unit.

9. Connect front panel devices (see Transmitter Front Panel on page 6 and Receiver

Front Panel on page 9 for connector details), restore the power supply, and test the

transmitter and receiver system. Make any cabling adjustments before final installation, as the cables will be inaccessible afterwards.

Mud Ring Installation

should not have a boot installed.

one unit needs a power supply (see Power Supply Wiring on page 11 and

Ground Loops on page 15).

1. Using the mud ring as a guide, mark the edges and cut out the material within the

marked area.

2. Insert the mud ring into the opening, rotate and secure the locking arms with the

supplied screws shown in figure 3.

3. Follow steps 6 through 9 of above, and Final Installation on the next page.

Wall

Mud Ring

Figure 3. Installing the Mud Ring

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 5

Page 13

Final Installation

INPUTS

AUDIO

Tx Rx GTxRx

RS-232 IR

OVER DTP

Sleeve ( )

Tip

After testing and making any adjustments, do the following:

1. At the power outlet, unplug the power supply.

NOTE: One power supply can power both the transmitter and the receiver (see

Power Supply Wiring on page 11 and Ground Loops on page 15).

2. Mount the transmitter or receiver into the wall box or mud ring, and attach the supplied

decorator-style faceplate to the unit (see figure 2 on page 4).

3. At the power outlet, reconnect the power supply. This powers up both units.

Transmitter Connections

Transmitter Front Panel

Figure 4. DTP HDMI 4K D Transmitter Front Panel Connectors

A HDMI input connector — Connect an HDMI cable between this port and the HDMI

output port of the digital video source.

B Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo

jack. Figure 5 shows how to wire the audio plug.

Left (+)

Ring

Right (

)

Figure 5. Audio Input Connector Wiring

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 6

Page 14

C RS-232/IR (Control) pass-through connector — Connect a serial communications

SIG

LINK

DTP OUT

POWER 12V

0.8 A MAX

port to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 communication (see RS-232 and IR connector wiring on page 13 to wire the connector).

NOTE: The RS-232 connector can also transmit one-way modulated IR signals.

Transmitter Rear Panel

Figure 6. DTP HDMI 4K D Transmitter Rear Panel Connectors

A DC power input connector — Plug the included external 12 VDC power supply

into either this 2-pole connector (see Power Supply Wiring on page 11 to wire the

power connector) or the power input connector on the receiver (see Figure 7, B on the following page).

B Transmitter output port — Connect one end of the twisted pair cable to the

RJ-45 connector on the transmitter (see Twisted Pair Recommendations for DTP

Communication on page 10 to properly wire the RJ-45 connectors).

ATTENTION:

• Do not connect these outputs to a telecommunications or computer data

network.

• Ne connectez pas ces appareils à des données informatiques ou à un réseau

de télécommunications.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 7

Page 15

Receiver Connections

SIG

LINK

DTP IN

POWER 12V

0.8 A MAX

Receiver Rear Panel

Figure 7. DTP HDMI 4K D Receiver Rear Panel Connectors

A Receiver input ports — Connect the opposite end of the twisted pair cable from the

transmitter output connector (see B on the previous page) to this RJ-45 connector (see Twisted Pair Recommendations for DTP Communication on page 10 to properly wire the RJ-45 connectors).

ATTENTION:

• Do not connect these outputs to a telecommunications or computer data

network.

• Ne connectez pas ces appareils à des données informatiques ou à un réseau

de télécommunications.

B DC power input connector — Plug the included external 12 VDC power supply

into either this 2-pole connector (see Power Supply Wiring on page 11 to wire the power connector) or the power input connector on the transmitter (see Figure 6,

on the previous page).

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 8

Page 16

Receiver Front Panel

OUTPUTS

AUDIO

Tx Rx GTxRx

RS-232 IR

OVER DTP

Figure 8. DTP HDMI 4K D Receiver Front Panel Connectors

A HDMI output connector — Connect an HDMI display for the transmitted direct digital

image.

B Audio output connector — Connect a stereo audio device to this 3.5 mm mini stereo

jack to receive the unbalanced audio output (see figure 5 on page 6 for wiring details).

C RS-232 and IR (control) pass-through connector — Connect a serial

communications port to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 communication (see RS-232 and IR Connector Wiring on page 13 to wire the connector).

NOTE: The RS-232 connector can also transmit one-way modulated IR signals.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 9

Page 17

Twisted Pair Recommendations for DTP Communication

TP Wires

Pins:

Use the following pin configurations for both ends of the shielded twisted pair cables.

12345678

Figure 9. TP Cable Termination

ATTENTION:

• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or

• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF

TIA/EIA T

568 B

Wire color

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

STP201 cable to link the device with DTP transmitters or receivers.

d’Extron ou le câble STP201 pour relier le appareil avec les émetteurs ou les récepteurs DTP.

Supported Cables

The distribution ampliﬁers are compatible with shielded twisted pair cable (F/UTP, SF/UTP, and S/FTP).

Cable Recommendations

Extron recommends using the following practices to achieve full transmission distances and reduce transmission errors.

• Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best

performance:

• XTP DTP 24/1000 Non-Plenum 1000’ (305 m) spool 22-236-03

• XTP DTP 24P/1000 Plenum 1000’ (305 m) spool 22-235-03

• XTP DTP 24 Plug Package of 10 101-005-02

• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid

conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard.

• Limit the use of more than two pass-through points, which may include patch points,

punch down connectors, couplers, and power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the

following:

• Do not exceed 40% ﬁll capacity in conduits.

• Do not comb the cable for the ﬁrst 20 meters, where cables are straightened,

aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 10

Page 18

Power Supply Wiring

NOTES:

• Only one power supply is required. A single power supply connected to either unit

• A power supply is included with each individually-packaged transmitter.

• Do not tin the power supply leads before installing them in the direct insertion

Figure 10 shows how to wire the power connector. Snap the provided ferrite bead onto the DC power cable, between the power supply and the connector on the HDMI unit.

in the pair powers both units.

connector. Tinned wires are not as secure in the connectors and could be pulled out.

3/16"

(5 mm) Max.

Smooth

Ridges

Captive Screw

SECTION A–A

Power Supply

Output Cord

Connector

Figure 10. Power Connector Wiring

CAUTION: The wires must be kept separate while the power supply is plugged in.

Remove power before wiring.

ATTENTION : Les deux cordons d’alimentation doivent être tenus à l’écart l’un de

l’autre quand l’alimentation est branchée. Couper l’alimentation avant de faire l’installation électrique.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 11

Page 19

ATTENTION:

• Always use a power supply supplied and or speciﬁed by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que le produit ﬁnal.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently ﬁxed to building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être ﬁxée de façon permanente à une structure de bâtiment ou à une structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the

power supply and the unit. The ridges on the side of the cord (see ﬁgure 10 on previous page) identify the power cord negative lead.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du cordon permettent de repérer le pôle négatif du cordon d’alimentation.

• To verify the polarity before connection, plug in the power supply with no load and

check the output with a voltmeter.

• Pour vériﬁer la polarité avant la connexion, brancher l’alimentation hors charge et

mesurer sa sortie avec un voltmètre.

• The length of the exposed (stripped) copper wires is important.

The ideal length is 3/16 inch (5 mm). Longer bare wires can short together.

Shorter wires are not as secure in the connectors and could be pulled out.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une

utilisation dans les espaces d’aération ou dans les cavités murales.

• If not provided with a power supply, this product is intended to be supplied by a

power source marked “Class 2” or “LPS” and rated at 12 VDC and a minimum of

1.0 A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit

être alimenté par une source d’alimentation de classe 2 ou LPS et paramétré à 12 V et 1.0 A minimum.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 12

Page 20

RS-232 and IR Connector Wiring

Figure 11 shows how to wire the RS-232 and IR connector on the front panel of units.

RS-232

Tx Rx G Tx Rx

Gnd

FunctionPin

Transmit data

Receive data Signal ground

RS-232

Tx Rx G Tx Rx

Do not tin the wires!

Ground (G) Receive (Rx) Transmit (Tx)

Bidirectional

Controlling

Device

Ground (G) Receive (Rx) Transmit (Tx)

Do not tin the wires!

Figure 11. RS-232 and IR Connector Wiring

NOTE: Do not tin the power supply leads before installing them in the direct insertion

connector. Tinned wires are not as secure in the connectors and could be pulled out.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 13

Page 21

Operation

DTP HDMI 4K D Series Tx Front Panel DTP HDMI 4K D Series Rx Front Panel

INPUTS

OVER DTP

RS-232 IR

AUDIO

Tx Rx GTxRx

AUDIO

OUTPUTS

OVER DTP

RS-232 IR

Tx Rx GTxRx

Figure 12. DTP HDMI 4K D Transmitter and Receiver Power Indicators

NOTE: Both transmitter and receiver have power indicators in the locations shown.

Transmitter Power Indicator

A Power LED — This two-color front panel LED lights to indicate signal and power status

as follows:

• Amber — The unit is receiving power but no signal on the HDMI input.

• Green — The unit is receiving power and a signal is present on the HDMI input.

Receiver Power Indicator

B Power LED — This two-color front panel LED lights to indicate signal and power status

as follows:

• Amber — The unit is receiving power but no signal on the TP input.

• Green — The unit is receiving power and a signal is present on the TP input.

System Operation

After the transmitter, the receiver, and their connected devices are powered up, the system is fully operational. If any problems are encountered, ensure that all cables are routed and connected properly.

NOTE: Ensure that the video source and display are properly connected to the

transmitter and receiver pair, and that the transmitter, the receiver, and the display have power applied before power is applied to the video source. If all other devices are not turned on before the video source, the image may not appear.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 14

Page 22

Ground Loops

When installing the DTP HDMI 4K D series of products, be sure to avoid scenarios where the ground potential differs greatly between the locations where the DTP transmitter and DTP receiver are installed. Such situations can cause ground loops, which can result in image drops, no image, or damage to the units. If such installations cannot be avoided, it is necessary to isolate the ground between the DTP transmitter and receiver.

NOTES:

• Grounding DTP series units will disable analog audio transmission and the remote

power feature.

• Both DTP transmitter and receiver will need to be powered locally.

To eliminate a ground loop:

1. Remove all screws on the left, right, and top of both the DTP transmitter and receiver

units.

2. Remove the rear enclosure of each unit.

3. Locate and remove shunt jumpers at locations labeled JMP2 and JMP3 on both

transmitter and receiver (see figure 13 for jumper locations).

JMP 3 JMP 2

JMP 1

JMP

DTP HDMI 4K D Series Tx DTP HDMI 4K D Series Rx

Figure 13. DTP HDMI 4K D Internal Jumper Locations

4. Replace the rear enclosures and screws.

5. Install units with an external power supply placed at each end.

6. Use UTP cable between the DTP transmitter and receiver. If STP cable has already been

installed and terminated, disconnect the shielding at one end to discontinue the ground path.

DTP HDMI 4K D Series Transmitter and Receiver • Installation and Operation 15

Page 23

Reference

(10.87 cm

Template for the 2-gang

Information

This section includes decorator-style wallplate template dimensions for installation of the DTP HDMI 4K D Series transmitters and receivers.

Decorator-Style Wallplate Template Dimensions

To create a template, use the dimensions shown on figure 14.

NOTES:

• The drawing is not full size or to scale. DO NOT scale up or print to use as a

template.

• Full size templates are available online at www.extron.com.

mounting bracket

4.28" )

3.06"

(7.78 cm)

4.26" (10.83 cm)

3.75" (9.53 cm)

Recommended cut-out area for the installation surface.

SURFACE

CUT-OUT AREA

FOR WALL MOUNT

Top Panel

Figure 14. Decorator-Style Wallplate Template Dimensions

DTP HDMI 4K D Series Transmitter and Receiver • Reference Information 16

Page 24

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Extron Electronics 1230 South Lewis Street Anaheim, CA 92805 U.S.A.

Japan:

Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan

Europe and Africa:

Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands

Asia:

Extron Asia Pte Ltd 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363 Singapore

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modiﬁcations were made to the product that were not authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040 Asia: 65.6383.4400 Japan: 81.3.3511.7655

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or ﬁtness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

China:

Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China

Middle East:

Extron Middle East Dubai Airport Free Zone F13, PO Box 293666 United Arab Emirates, Dubai