Extron Electronics DTP HDMI 230 D User Manual

DTP HDMI 230 D

HDMI Twisted Pair Extender
Transmitters and Receivers

User Guide

HDMI Extenders

68-2366-01 Rev. B

07 13

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended

to alert the user of the presence of uninsulated dangerous voltage
within the product’s enclosure that may present a risk of electric
shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT: Ce pictogramme, , lorsqu’il est utilisé sur

le produit, signale à l’utilisateur la présence à l’intérieur du boîtier
du produit d’une tension électrique dangereuse susceptible de
provoquer un choc électrique.

ATTENTION: Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.fr.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Chinese Simplified（简体中文）

警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险

电 压 ，有 触 电 危 险 。

注意： 产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 www.extron.cn，参见 Extron
安全规范指南，产品编号 68-290-01。

Chinese Traditional（繁體中文）

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意 若產品上使用此符號，是為了提醒使用者。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細
資訊，請瀏覽 Extron 網站：www.extron.cn，然後參閱《Extron 安全性與法規遵

守手冊》，準則編號 68-290-01。

Japanese

警告: この記 号 が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意: この 記号 が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操 作と保守( 整備)の 指示についてユーザーの

  注意を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ クスト ロ ン の ウ ェブ サ イト www.extron.jpより

『Extron Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧くだ さ い 。

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.de.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro
del producto, lo que puede representar un riesgo de descarga
eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con
el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.es.

Korean

경고: 이 기호 , 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.

주의: 이 기호 , 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련
항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.co.kr)의
Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; the user must correct the interference at his own expense.

NOTE: The Twisted Pair Extension technology works with unshielded twisted pair

(UTP) or shielded twisted pair (STP) cables; but, to ensure FCC Class A and CE
compliance, STP cables and STP connectors are required.

For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

WARNING: A warning indicates a situation that has the potential to result in death or

severe injury.

CAUTION: A caution indicates a situation that may result in minor injury.

ATTENTION: Attention indicates a situation that may damage or destroy the product or

associated equipment.

NOTE: A note draws attention to important information.

Copyright

© 2013 Extron Electronics. All rights reserved.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks
Systems, Inc. or Extron Electronics:

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IPIntercom, IPLink,
Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System
Integrator, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTP Systems

Registered Service Mark

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator, DSPConfigurator, DSVP
(Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel
Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, XTRA, ZipCaddy, ZipClip

(SM)

: S3 Service Support Solutions

(R)

, registered service marks

Registered Trademarks

Trademarks (™

(SM)

, and trademarks

(®)

)

(TM)

are the property of RGB

Contents

Introduction............................................................ 1

About this Guide ................................................. 1

About the DTP HDMI 230 D Extenders ............... 1

Twisted Pair Cable Advantages ....................... 2

Transmission Distance .................................... 2

Features ............................................................. 2

Installation and Operation .................................. 3

Mounting the Transmitter or Receiver .................. 3

Decora Unit Mounting ..................................... 3

Transmitter Connections ..................................... 6

Transmitter Front Panel ................................... 6

Transmitter Rear Panel .................................... 7

Receiver Connections ......................................... 8

Receiver Front Panel ....................................... 8

Receiver Rear Panel ....................................... 9

Connector and Cable Details ............................ 10

TP Cable Termination and

Recommendations ...................................... 10

Power Supply Wiring ........................................ 11

RS-232 and IR Connector Wiring ..................... 12

Operation ......................................................... 12

Transmitter Power Indicator .......................... 13

Receiver Power Indicator .............................. 13

System Operation ......................................... 13

Ground Loops .................................................. 14

Reference Information ...................................... 15

Decora Template Dimensions ........................... 15

vDTP HDMI 230 D Transmitter and Receiver • Contents

Introduction

• About this Guide

• About the DTP HDMI 230 D Extenders

• Features

About this Guide

This guide describes the Extron DTP HDMI 230 D family of High-Definition Multimedia
Interface (HDMI™) Extenders, which consists of DTP HDMI 230 D transmitters and
DTP HDMI 230 D receivers. This guide describes how to install, operate, and configure
them.

About the DTP HDMI 230 D Extenders

The Extron DTP HDMI 230 D extenders are a family of HDMI transmitters and receivers (see
figure 1) which are housed in enclosures that can be mounted in Underwriters Laboratories
(UL) standard wall boxes with Decora®-style face plates. A transmitter and receiver pair
extends the usable distance of HDMI digital video and RS-232 or IR control signals over one
Category (CAT) 5e, 6, 6a, or 7 unshielded twisted pair (UTP) or shielded twisted pair (STP)
cable. The DTP HDMI 230 D transmitter and receiver also route audio. The video, control,
and audio (if applicable) signals can be transmitted up to 230 feet (70 m).

CATx Cable
up to 230' (70 m)

Extron
DTP HDMI 230 D Rx

Receiver

OUTPUTS

IR

OVER DTP

RS-232

TxRx G Tx Rx

AUDIO

Flat Panel
Display

RS-232

HDMI

INPUTS

IR

OVER DTP

RS-232

TxRx G Tx Rx

AUDIO

Blu-ray Player

Extron
DTP HDMI 230 D Tx

Transmitter

RS-232

HDMI

100

RELAY

LINK
ACT

31

INPUT

IR

31

42

31

COM

42

TXRX

IPL 250

1

42

2

R

3

®

TCP/IP

Tou c hLink

Control
System

VCR

DVD

DOC
CAM

LAPTOP

PC

ON

OFF

DISPLAY
MUTE

SCREEN
UP

SCREEN
DOWN

Figure 1. Typical Transmitter and Receiver Application

A DTP HDMI 230 D system consists of a transmitter (Tx) and a receiver (Rx). The pair can
handle a single HDMI digital video signal and a bidirectional RS-232 or IR link.

The DTP HDMI 230 D transmitter and receiver are sold separately. Each purchased
transmitter is shipped with a single external desktop 12 VDC power supply that accepts 100
to 240 VAC, 50-60 Hz input. A single power supply connected to either the transmitter or
the receiver can power both units through the twisted pair cable that links the units.

DTP HDMI 230 D Transmitter and Receiver • Introduction 1

Twisted Pair Cable Advantages

Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial
or HDMI cable. These transmitter and receiver twisted pair (TP) products make cable
runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors is
simple, quick, and economical (see Connector and Cable Details on page 10 for more
information).

NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

cable to link the transmitter and receiver. The DTP HDMI 230 Tx/Rx does not work
properly with these cables.

Control communications

The RS-232 or infrared (IR) communications are pass-through only. The transmitter and
receiver do not generate or respond to these signals.

Transmission Distance

The maximum transmission distance is determined by the resolution of the signal and the
twisted pair cable, graphics card, and display used in the system.

• With CAT 5e, 6, 6a, or 7 UTP or STP cable, the DTP HDMI 230 D transmitters and

receivers can transmit and receive 720p, 1080i or 1080p HDTV video signals up to
230 feet (70 m).

Features

Transmits single link HDMI-D signals over one CAT 5e, 6, 6a, or 7 cable — Standard
twisted pair cables provide an economical, easily installed cable solution.

Supports DDC and HDCP transmission — The DTP HDMI 230 D transmitters and
receivers fully support long distance transmission of the DDC and HDCP signals.

Control communications pass-through — Bidirectional RS-232 or IR control signals
can be transmitted alongside the HDMI signal, so that the remote display can be controlled
without the need for additional cabling.

Audio routing — The DTP HDMI 230 D transmitters and receivers also route unbalanced
stereo audio.

Supports CEC signal transmission
Wall-mountable enclosures
External 100 VAC to 240 VAC, 50-60 Hz, international power supply — Included with

transmitters.
Remote powering of the transmitter or receiver — Only one power supply is necessary

to power both devices.

DTP HDMI 230 D Transmitter and Receiver • Introduction 2

Installation and Operation

This section describes the installation and the operation of the DTP HDMI 230 D, including:

• Mounting the Transmitter or Receiver

• Transmitter Connections

• Receiver Connections

• Connector and Cable Details

• Power Supply Wiring

• RS-232 and IR Connector Wiring

• Operation

• Ground Loops

Mounting the Transmitter or Receiver

ATTENTION: Installation and service must be performed by experienced personnel.

Decora Unit Mounting

The DTP HDMI 230 D transmitter and receiver can be installed in a two-gang electrical wall
box, or with a mud ring, with a Decora wall plate cover (supplied).

The installation must conform to national and local building, electrical, and safety codes and
to the size requirements of the wall plate.

UL and safety guidelines

The following UL guidelines pertain to the installation of the Decora transmitters and
receivers into a wall or furniture.

• These units are not to be connected to a centralized DC power source or used beyond

their rated voltage range.

• These units must be installed in UL-listed wall boxes.

• These units must be installed with conduit in accordance with National Electrical Code.

Site preparation and wall box installation

Choose a location that allows cable runs without interference. Allow enough depth for both
the wall box and the cables. Install the cables into the wall, furniture, or conduits before
installing the wall plate.

NOTE: The Decora units are very deep and have connectors on the back side. Extron

recommends a 2-gang wall box which has a depth of at least 3.0 inches (7.6 cm) to
accommodate the connectors and cables.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 3

To install a new wall box, perform steps 1 through 9. If a suitable wall box is already

Wa
flush with edge of box.

installed, perform steps 6 through 9 on the next page. UL-listed wall boxes are
recommended.

1. If a wall box is not available to use for a template, use the Decora Template

Dimensions on page 15 to create a template. If installing directly into furniture, cut out

the center portion of the template.

2. Place the wall box (or the template) against the installation surface, and mark the

opening guidelines.

3. Cut out the material from the marked area.

4. Insert the wall box into the opening. The rear connectors on the box or wall plate should

fit easily into the opening. Enlarge or smooth the edges of the opening if needed.

5. Secure the wall box with nails or screws, leaving the front edge flush with the outer wall

or furniture surface (see figure 2).

NOTES:

• If attaching the wall box to wood, use four #8 or #10 screws or 10-penny

nails. A minimum of 0.5 inch (1.3 cm) of screw thread must penetrate the
wood.

• If attaching the wall box to metal studs or furniture, use four #8 or #10

self-tapping sheet metal screws or machine bolts with matching nuts.

ll opening is

Cable
Clamp

Signal Output
Cable

Wall Stud

Screws or
Nails

INPUT

AUDIO

IN

Extron
DTP HDMI 230 D

IR

OVER DTP

RS-232

Tx Rx Tx RxG

Decora Faceplate

Figure 2. Installing the Wall Box and Mounting the Unit

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 4

6. Feed the twisted pair cables and, if applicable, the power cables through the opening

and through the wall box punch-out holes, securing them with cable clamps to provide
strain relief.

NOTES:

• In order to fit in the wall box, the twisted pair cables and RJ-45 connectors

should not have a boot installed.

• One power supply can power both the transmitter and the receiver, so only

one unit needs a power supply (see Power Supply Wiring on page 11 and

Ground Loops on page 14.

7. Trim back and insulate exposed cable shields with heat shrink to reduce the chance of

short circuits.
To prevent short circuits, the outer foil shield can be cut back to the point where the

cable exits the cable clamp.

8. Connect the cables to the rear of the unit.

9. Connect front panel devices (see Connections on page 6 for connector details),

restore the power supply, and test the transmitter and receiver system. Make any
cabling adjustments before final installation, as the cables will be inaccessible
afterwards.

Mud ring installation

1. Using the mud ring as a guide, mark the edges and cut out the material within the

marked area.

2. Insert the mud ring into the opening, rotate and secure the locking arms with the

supplied screws shown in figure 3.

3. Follow steps 6 through 9 of Site preparation and wall box installation above, and

Final installation on the next page.

Mud Ring

Wall

Figure 3. Installing the Mud Ring

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 5

Final installation

After testing and making any adjustments, do the following:

1. At the power outlet, unplug the power supply.

NOTE: One power supply can power both the transmitter and the receiver (see

Power Supply Wiring on page 11 and Ground Loops on page 14).

2. Mount the transmitter or receiver into the wall box or mud ring, and attach the supplied

Decora faceplate to the unit (see figure 2 on page 4).

3. At the power outlet, reconnect the power supply. This powers up both units.

Transmitter Connections

The DTP HDMI 230 D transmitter is in an enclosure that can be mounted in UL-listed
standard wall boxes with Decora-style face plates.

Transmitter Front Panel

INPUTS

1

OVER DTP

2

AUDIO

RS-232 IR

Tx Rx GTxRx

3

Figure 4. DTP HDMI 230 D Transmitter Front Panel Connectors

a HDMI input connector — Connect an HDMI cable between this port and the HDMI

output port of the digital video source.

b Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo

jack. Figure 5 shows how to wire the audio plug.

Tip

Left (+)

Ring

Right (

-

)

Sleeve ( )

Figure 5. Audio Input Connector Wiring

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 6

c RS-232/IR (Control) pass-through connector — Connect a serial communications

port to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232
communication (see RS-232 and IR connector wiring on page 12 to wire the
connector).

NOTE: The RS-232 connector can also transmit one-way modulated infrared (IR)

signals.

Transmitter Rear Panel

2

SIG

DTP OUT

LINK

POWER
12V

0.8 A MAX

1

DTP 230 D Tx

Figure 6. DTP HDMI 230 D Transmitter Rear Panel Connectors

a DC power input connector — Plug the included external 12 VDC power supply into

either this 2-pole connector (see Power supply wiring on page 11 to wire the power
connector) or the power input connector on the receiver (see b on the following page).

b Transmitter output port — Connect one end of the twisted pair cable to the

RJ-45 connector on the transmitter (see Connector and Cable Details on page 10 to
properly wire the RJ-45 connectors).

ATTENTION: Do not connect this device to a telecommunications or computer

data network.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 7

Receiver Connections

The wall-mountable receiver is in an enclosure that can be mounted in UL-listed standard
wall boxes with Decora-style face plates.

Receiver Rear Panel

Figure 7 shows the rear panel of the DTP HDMI 230 D receiver.

LINK

1

SIG

DTP IN

DTP 230 D Rx

POWER
12V

0.8 A MAX

2

Figure 7. DTP HDMI 230 D Receiver Rear Panel Connectors

a Receiver input ports — Connect the opposite end of the twisted pair cable from the

transmitter output connector (see b on the previous page) to this RJ-45 connector (see

Connector and Cable Details on page 10 to properly wire the RJ-45 connectors).

ATTENTION: Do not connect this device to a telecommunications or computer

data network.

b DC power input connector — Plug the included external 12 VDC power supply

into either this 2-pole connector (see Power Supply Wiring on page 11 to
wire the power connector) or the power input connector on the transmitter (see
a on the previous page).

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 8

Receiver Front Panel

Figure 8 shows the front panel of the DTP HDMI 230 D receiver.

1

2

Figure 8. DTP HDMI 230 D Receiver Front Panel Connectors

a HDMI output connector — Connect an HDMI display for the transmitted direct digital

image.

AUDIO

OUTPUTS

OVER DTP

RS-232 IR

Tx Rx GTxRx

3

b Audio output connector — Connect a stereo audio device to this 3.5 mm mini stereo

jack to receive the unbalanced audio output (see figure 5 on page 7 for wiring details).

c RS-232 and IR (control) pass-through connector — Connect a serial

communications port to this 3.5 mm, 5-pole captive screw connector for bidirectional
RS-232 communication (see RS-232 and IR Connector Wiring on page 12 to wire
the connector).

NOTE: The RS-232 connector can also transmit one-way modulated infrared (IR)

signals.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 9

Connector and Cable Details

TP Wires

Pins:

TP Cable Termination and Recommendations

Figure 9 details the recommended termination of both ends of TP cables with RJ-45
connectors in accordance with the TIA/EIA T 568B wiring standard.

12345678

Pin

Figure 9. TP Cable Termination

NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

cable to link the transmitter and receiver. The DTP HDMI 230 D Tx/Rx does not work
properly with these cables.

TIA/EIA T

568 B

Wire color

White-orange

1

Orange

2
3

White-green

4

Blue

5

White-blue
Green

6
7

White-brown

8

Brown

Supported cables —
The DTP HDMI 230 D is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair (F/UTP,

SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable.

Cable recommendations —
Extron recommends using the following practices to achieve full transmission distances up

to 230 feet (70 m) and reduce transmission errors.

• Use the following Extron XTP DTP 24 SF/UTP cables and DTP 24 connectors for the

best performance:

• XTP DTP 24/1000 Non-Plenum 1000’ (305 m) spool 22-236-03

• XTP DTP 24P/1000 Plenum 1000’ (305 m) spool 22-235-03

• XTP DTP 24 Plug Package of 10 101-005-02

• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid

conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.

• Use no more than two pass-through points, which may include patch points, punch

down connectors, couplers, and power injectors. If these pass-through points are
required, use CAT 6 or 6a shielded couplers and punch down connectors.

NOTE: When using CAT 5e and CAT 6 cable in bundles or conduits, consider the

following:

• Do not exceed 40% fill capacity in conduits.

• Do not comb the cable for the first 20 meters, where cables are straightened,

aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or Velcro®.

• Separate twisted pair cables from AC power cables.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 10

Power Supply Wiring

AA

NOTES:

• Only one power supply is required. A single power supply connected to either unit

• A power supply is included with each individually-packaged transmitter.

Figure 10 shows how to wire the connector. Snap the provided ferrite bead onto the DC
power cable, between the power supply and the connector on the HDMI unit.

in the pair powers both units.

3/16"

(5 mm) Max.

Smooth

SECTION A–A

Power Supply

Output Cord

Ridges

Captive Screw

Connector

Figure 10. Power Connector Wiring

WARNING: The two power cord wires must be kept separate while the power supply is

plugged in. Remove power before wiring.

ATTENTION:

• Always use a power supply supplied and or specified by Extron. Use of an

unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product. Unless otherwise stated, the
AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to
building structure or similar structure.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage

the power supply and the unit. The ridges on the side of the cord (see figure 10)
identify the power cord negative lead.

• To verify the polarity before connection, plug in the power supply with no load and

check the output with a voltmeter.

• The length of the exposed (stripped) copper wires is important.

The ideal length is 3/16 inch (5 mm). Longer bare wires can short together.
Shorter wires are not as secure in the connectors and could be pulled out.

connector. Tinned wires are not as secure in the connectors and could be pulled out.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 11

NOTE: Do not tin the power supply leads before installing them in the direct insertion

RS-232 and IR Connector Wiring

Figure 11 shows how to wire the RS-232 and IR connector for the DTP HDMI 230 D units.

IR

RS-232

Tx Rx G Tx Rx

Gnd

FunctionPin

TX

Transmit data

RX

Receive data
Signal ground

RS-232

IR

Tx Rx G Tx Rx

Operation

Do not tin the wires!

Ground (G)
Receive (Rx)
Transmit (Tx)

Bidirectional

Controlling

Device

Ground (G)
Receive (Rx)
Transmit (Tx)

Do not tin the wires!

Figure 11. RS-232 and IR Connector Wiring

ATTENTION: The length of the exposed (stripped) copper wires is important.

The ideal length is 3/16 inch (5 mm). Longer bare wires can short together. Shorter
wires are not as secure in the connectors and could be pulled out.

NOTE: Do not tin the power supply leads before installing them in the direct insertion

connector. Tinned wires are not as secure in the connectors and could be pulled out.

Figure 12 shows the power indicator on the Decora transmitter.

NOTE: Both transmitter and receiver have power indicators in the location shown.

1

INPUTS

OVER DTP

RS-232 IR

AUDIO

Tx Rx GTxRx

2

OUTPUTS

OVER DTP

AUDIO

RS-232 IR

Tx Rx GTxRx

Figure 12. DTP HDMI 230 D Transmitter and Receiver Power Indicators

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 12

Transmitter Power Indicator

a Power LED — This two-color front panel LED lights to indicate signal and power status

as follows:

• Amber — The unit is receiving power but no signal on the HDMI input.

• Green — The unit is receiving power and a signal is present on the HDMI input.

Receiver Power Indicator

b Power LED — This two-color front panel LED lights to indicate signal and power status

as follows:

• Amber — The unit is receiving power but no signal on the TP input.

• Green — The unit is receiving power and a signal is present on the TP input.

System Operation

After the transmitter, the receiver, and their connected devices are powered up, the system
is fully operational. If any problems are encountered, ensure all cables are routed and
connected properly.

NOTE: Ensure that the video source and display are properly connected to the

transmitter and receiver pair, and that the transmitter, the receiver, and the display
have power applied before power is applied to the video source. If all other devices
are not turned on before the video source, the image may not appear.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 13

Ground Loops

When installing the DTP HDMI 230 D series products, be sure to avoid scenarios where
the ground potential differs greatly between the locations where the DTP transmitter and
DTP receiver are installed. Such situations can cause ground loops, which can result in
image drops, no image, or damage to the units. If such installations cannot be avoided, it is
necessary to isolate the ground between the DTP transmitter and receiver.

NOTES:

• Grounding DTP series units will disable analog audio transmission and the remote

power feature.

• Both DTP transmitter and receiver will need to be powered locally.

To eliminate a ground loop:

1. Remove all screws on the left, right, and top of both the DTP transmitter and receiver

units.

2. Remove the rear enclosure of each unit.

3. Locate and remove shunt jumpers at locations labeled JMP2 and JMP3 on both

transmitter and receiver (see figure 13 for jumper locations).

JMP 3
JMP 2

JMP 1

JMP 3
JMP 1

JMP 2

DTP HDMI 230 D Tx DTP HDMI 230 D Rx

Figure 13. DTP HDMI 230 D Internal Jumper Locations

4. Replace the rear enclosures and screws.

5. Install units with an external power supply placed at each end.

6. Use UTP cable between the DTP transmitter and receiver. If STP cable has already been

installed and terminated, disconnect the shielding at one end to discontinue the ground
path.

DTP HDMI 230 D Transmitter and Receiver • Installation and Operation 14

Reference

(10.87 cm

Template for the 2-gang

Information

This section includes decora template dimensions for installation of the DTP HDMI 230 D
transmitters and receivers.

Decora Template Dimensions

To create a template, use the dimensions shown on figure 14.

NOTES:

• The drawing is not full size or to scale. DO NOT scale up or print to use as a

template.

• Full size templates are available online at www.extron.com.

mounting bracket

4.28"
)

3.06"

(7.78 cm)

4.26" (10.83 cm)

3.75" (9.53 cm)

Recommended
cut-out area
for the installation
surface.

SURFACE

CUT-OUT AREA

FOR WALL MOUNT

Top Panel

Figure 14. Decora Template Dimensions

DTP HDMI 230 D Transmitter and Receiver • Reference Information 15

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America,
and Central America:

Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.

Europe and Africa:

Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands

Japan:

Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan

China:

Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China

Asia:

Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363

Middle East:

Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai

Singapore

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040
Asia: 65.6383.4400 Japan: 81.3.3511.7655

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX

Extron Europe

+800.3987.6673
(Inside Europe Only)

+31.33.453.4040
+31.33.453.4050 FAX

© 2013 Extron Electronics All rights reserved. www.extron.com

Extron Asia

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800
+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571
+82.2.3444.1575 FAX

Extron India

1800.3070.3777
(Inside India Only)

+91.80.3055.3777
+91.80.3055.3737 FAX