Extron Electronics DTP DVI 330 User Manual
DTP DVI 330 • Setup Guide
DTP DVI 330 Tx
Connected RS-232
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron DTP DVI 330 digital video extender. The DTP DVI 330 transmitter and receiver pair can extend
a DVI signal up to 330 feet (100 m).
NOTE: For full installation and operation details, see the DTP DVI 330 User Guide, available at
www.extron.com).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
INPUTS
AUDIO
Front Rear
DVI-D
1 523
LOCAL OUTPUT
DTP DVI 330 Tx
DTP DVI 330 Rx
OUTPUTS
DVI-D
Front Rear
6 5
AUDIO
L R
DTP DVI 330 Rx
Step 2 — Connections
DVI Input connector (Tx) — Connect a DVI cable between this port and the DVI output port of the digital video source.
a
Local Output connector (Tx) — If desired, connect a DVI monitor for local monitoring of the input digital image.
b
Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
c
RS-232 and IR connectors (both units) — To pass serial or infrared data or control
d
signals, such as serial control of a projector, connect the master device to the transmitter
and the slave device to the receiver via the RS-232 and IR captive screw connector on both
units.
DTP RJ-45 connectors (both units) — Connect transmitter DTP Out to receiver DTP In.
e
Extron recommends that you terminate both cable ends in accordance with the following
specications, at a minimum:
z TIA/EIA T 568 B z CAT 6A, shielded
z 24 AWG, solid conductor
ATTENTION: Do not connect these devices to a computer data or telecommunications
network.
Sig(nal) LED (both units) — This LED lights when the unit is receiving a TMDS clock signal on the
DVI input (transmitter) or any valid signal on the DTP In connector (receiver).
Link LED (both units) — This LED lights when a valid link is established between the units on the
DTP cable.
DVI Output connector (Rx) — Connect a display with a DVI input for display of the transmitted direct digital image.
f
POWER
12V
0.8 A MAX
POWER
12V
0.8 A MAX
8
8
DDC ROUTE
ON
SHARE
REMOTE
1 2
LOCAL
SIG LINK
SIG LINK
DTP IN
Tx/Rx
Pins
RxTx
Rx GTx
RS-232 IR
DTP OUT
and IR Device Pins
Transmit pin on connected unit
Receive pin on connected unit
Ground
Transmit pin on connected unit
Receive pin on connected unit
Pins:
12345678
TP Wires
OVER DTP
RS-232 IR
Rx GTx
4
OVER DTP
RS-232 IR
Rx GTx
47
TIA/EIA T
568 B
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
RxTx
RxTx
No Ground Here
Rear
(Tx)
LOCAL
SPARE
REMOTE
DDC ROUTE
POWER
12V
0.8 A MAX
1 2
ON
2 3
1
AA
DTP DVI 330 • Setup Guide (Continued)
Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio
g
captive screw connector. See the drawing below.
Tip
LR
Ring
Sleeves
Ring
Tip
Do not tin the wires!
Tip
Sleeves
Tip
No Ground Here
Unbalanced Stereo Output Balanced Stereo Output
ATTENTION: Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–) contacts.
Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source.
h
Connect the power supply to either unit as shown at right.
ATTENTION: This product is intended to be supplied by a Listed Power
Unit marked “Class 2” or “LPS,” rated 12 VDC, 1.0 A. Always use a
power supply supplied by or specied by Extron. Use of an unauthorized
power supply voids all regulatory compliance certication and may cause
damage to the supply and the end product. Unless otherwise stated,
the AC/DC adapters are not suitable for use in air handling spaces or
in wall cavities. The installation must always be in accordance with
the applicable provisions of National Electrical Code ANSI/NFPA 70,
article 75 and the Canadian Electrical Code part 1, section 16. The power
supply shall not be permanently xed to a building structure or similar
structure.
NOTE: Only one power supply is required. A single power supply connected
to either unit in the pair powers both units. A power supply is included
with each transmitter.
LR
Smooth
SECTION A–A
Power Supply
Output Cord
Ridges
Captive
Screw
Connector
3"
16 (5 mm) Max.
Tie Wrap
Operation
After all devices are powered up, the system is fully operational. See the
denitions of the power indications (shown at right), below:
a Power LED (front panel) —
Amber — The unit is receiving power, either locally or remotely (on the DTP
cable).
Green — The unit is powered on and is receiving an active DVI signal, either
on the DVI input if a transmitter, or transmitted on the DTP cable if a receiver.
b Power LED (rear panel) —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
c DDC Route switch — This rear panel switch selects either the remote or local DVI display as the display data channel (DDC)
reference for EDID and HDCP communication.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3
Sales and Technical Support Hotline that is closest to you, at the number shown below.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
2
© 2012 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737
FAX
68-2342-50
Rev A
12 12
Loading...