Extron electronics DTP2 T 211, DTP2 R 211 User Manual

Download

Page 1

DTP2T/R211

HDMI Twisted Pair Transmitters and Receivers

User Guide

DTP Systems

68‑2938‑01 Rev. A

07 19

Page 2

Safety Instructions

Safety Instructions • English

WARNING: This symbol, ,when used on the product, is

intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa all’interno del contenitore del prodotto che può costituire un rischio di scosse elettriche.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide, part number 68‑290‑01, on the Extron website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung, EMI/EMF‑Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den Extron‑Richtlinien für Sicherheit und Handhabung (Artikelnummer 68‑290‑01) auf der Extron‑Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y mantenimiento recogidas en la documentación proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento de normativas, compatibilidad electromagnética, accesibilidad y temas relacionados, consulte la Guía de cumplimiento de normativas y seguridad de Extron, referencia 68‑290‑01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une tension électrique dangereuse susceptible de provoquer un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les informations de sécurité et de conformité Extron, réf. 68‑290‑01, sur le site Extron, www.extron.com.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative, compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo 68‑290‑01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01, na stronie internetowej Extron, www.extron.com.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

Page 3

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守( 整備)の指示についてユーザーの注意を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目については、エクストロンのウェブサイト www.extron.com より『 Extron Safety and Regulatory Compliance Guide』 ( P/N 68‑290‑01) をご覧ください。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을 경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks (®), registered service marks (SM), and trademarks (TM) are the property of RGBSystems, Inc. or ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks (

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free. Global Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation, SystemINTEGRATOR, TeamWork, TouchLink, V‑Lock, VideoLounge, VN‑Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks (™

)

AAP, AFL (Accu‑RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto‑Image, AVEdge, CableCover, CDRS(ClassD Ripple Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti‑Torque, PendantConnect, ProDSP, QS‑FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope‑Trigger, ShareLink, SIS, SimpleInstructionSet, Skew‑Free, SpeedNav, Triple‑Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and ZipCaddy

Page 4

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference; correcting the interference is at the expense of the user.

ATTENTION:

• The Twisted Pair Extension technology works with unshielded twisted pair (UTP)

• La technologie extension paires torsadées fonctionne avec les câbles paires

NOTES:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded

• For more information on safety guidelines, regulatory compliances, EMI/EMF

or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE compliance, STP cables and STP Connectors are required.

torsadées blindées(UTP) ou non blindées(STP). Afin de s’assurer de la compatibilité entre FCC ClasseA et CE, les câbles STP et les connecteurs STP sont nécessaires.

cables must be used to ensure compliance with FCC emissions limits.

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

Page 5

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2!

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character "0" is used for the number zero and "O" is the capital letter "o."

Computer responses and directory paths that do not have variables are written in the font shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are written in the font shown here:

From the File menu, select New. Click the OK button.

}

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

Page 6

Page 7

Introduction ................................................1

About this Guide .................................................. 1

About the DTP2211 Transmitter and Receiver .... 1

Control Communications ................................. 1

TP Cable Advantages ...................................... 2

Application Diagram ............................................ 2

Features .............................................................. 2

Installation and Operation............................5

Installation Overview ............................................ 5

Connections ........................................................ 6

Transmitter Rear Panel Connections ................ 6

Receiver Rear Panel Connections .................... 8

Securing the HDMI Connector ....................... 10

TP Cable Termination and

Recommendations ....................................... 11

Power Supply Wiring ..................................... 12

RS-232 and IR Connector Wiring .................. 14

Operations......................................................... 15

Front Panel Features ...................................... 15

Connecting to the Front Panel USB Port ........ 17

Resetting ....................................................... 18

Analog Audio Embedding (Transmitter) .......... 19

HDMI Audio De-embedding (Receiver) ........... 19

Remote Control .........................................20

Introduction to SIS ............................................. 20

Error Messages ............................................. 20

Timeout ......................................................... 20

Symbols Used in this Guide ............................... 21

Symbol Definitions ......................................... 21

Command and Response Table for SIS

Commands ...................................................... 22

Downloading and Updating Firmware ................ 24

Downloading Extron Firmware Loader ........... 24

Installing Firmware Loader ............................. 25

Downloading Firmware to a PC ..................... 25

Updating Firmware on a DTP2211 Device .... 26

Reference Information ............................... 31

Mounting the Transmitter or Receiver ................. 31

Tabletop Use ................................................. 31

Mounting kits ................................................. 31

UL Rack-Mounting Guidelines ....................... 32

Internal Settings ................................................. 32

viiDTP2 T/R 211 • Table of Contents

Page 8

DTP2 T/R 211 • Table of Contents viii

Page 9

Introduction

• About this Guide

• About the DTP2211 Transmitter and Receiver

• Application Diagram

• Features

About this Guide

This guide describes the Extron DTP2211 long distance High Definition Multimedia Interface (HDMI) Twisted Pair Extenders, which consists of a transmitter and receiver:

• DTP2T211 — 330feet (100meters) transmitter

• DTP2R211 — 330feet (100meters) receiver

This guide describes how to install, operate, and configure the transmitter and receiver.

About the DTP2211 Transmitter and Receiver

The Extron DTP2211 transmitter and receiver pair (see figure1 on the next page) extends the usable distance of HDMI digital video with resolutions up to 4K@60Hz (4:4:4), analog audio, remote power, and bidirectional RS-232 and infrared (IR) control signals over one Extron XTPDTP24 shielded twisted pair (STP) cable (recommended), or Category CAT 6a, or CAT 7 STP, or unshielded twisted pair (UTP) cable up to 330feet (100meters).

The DTP2211 devices extend the digital signal to Legacy DTP inputs 330feet (100meters) with a maximum resolution of up to 4K @ 60Hz, 4:4:4, supporting data rates up to 10.2Gbps.

The DTP2211 devices extend the digital signal to DTP2 inputs 330feet (100meters) with a maximum resolution of up to 4K @ 60Hz, 4:4:4, supporting data rates up to 18Gbps.

Both units are HDMI(2.0b and 1.4) and HDCP(2.2 and 2.0) compliant. HDCP, EDID, and CEC transmission is negotiated from source to sink.

• DTP2 transmitters feature configurable analog audio embedding that can be configured

via Simple Instructions Set (SIS) commands.

• DTP2 receivers feature configurable digital audio de-embedding, which can be selected

using the audio toggle switch on the rear panel.

The DTP2211 transmitter and receiver are housed in 1 inch tall, quarter rack width, 6inches deep metal enclosures. They can be set on a tabletop, mounted in a rack, or under or through furniture. The receiver can also be mounted on a projector bracket.

Control Communications

The RS-232 and IR communications are passive pass-through only. The transmitter and receiver do not generate or respond to the RS-232 and IR communication signals. HDCP, EDID and CEC are negotiated from source to sink, with the transmitter and receiver transparent during the exchange.

DTP2 T/R 211 • Introduction 1

Page 10

TP Cable Advantages

4K/HDR Display

Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial or HDMI cable. These transmitter and receiver twisted pair (TP) products make cable runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple, quick, and economical.

ATTENTION:

• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

• N’utilisez pas le câble audiovisuel Skew Free UTP version améliorée UTP23SF-4

Application Diagram

STATUS

POWER

INPUT

FAR END

LINK

CONFIG

OUTPUT

INPUTS

POWER 12V

AUDIO

--A MAX

cable to link the transmitter and receiver. The DTP2211 T/R do not work properly with these cables.

Extron ou le câble STP201 pour relier l’émetteur et le récepteur/sélecteur. Le DTP2211 T/R ne fonctionne pas correctement avec ces câbles.

IPL PRO S3

POWER 12V

0.3A MAX

OFF

SIG LINK

DTP+OUT

COM 1 COM 2 COM 3

Tx Rx RTS CTS

RS-232

DTP T HD 4K PLUS

OVER DTP

RS-232

TxRx Tx RxG

Tx Rx RTS CTS

Extron DTP2 T 211

Transmitter

LAN / PoE

Extron IPL Pro S 3

IP Link Pro Control Processor

Extron DTP2 R 211

Receive r

POWER 12V

--A MAX

POWER 12V

0.7A MAX

OVER DTP

RS-323 IR

TxRx TxRxG

CONFIG

SIG LINK

DTP IN

STATUS

SIG LINK

DTP+IN

OVER DTP

POWER

INPUT

FAR END

RS-232

LINK

OUTPUT

OFF

TxRx Tx RxG

DTP R HD 4K PLUS

OUTPUTS

AUDIO

DTP HDMI 330 Rx

AUDIO

L R

Features

WiFi

12 3 4

PC with 4K /HDR Video Outp ut

CATx Cable up to 330' (100 m) HDMIAudio

MODEL 80

FLAT PANEL

HDMI R S-232

Figure 1. Typical DTP2 211 Transmitter and Receiver Application

• Transmits HDMI plus control and analog audio up to 330 feet (100 meters) over

a shielded CATx cable — The DTP2T211 provides high reliability and maximum performance on an economical and easily installed cable infrastructure.

• Receives HDMI plus control and analog audio up to 330 feet (100 meters) over

a shielded CATx cable — The DTP2R211 provides high reliability and maximum performance on an economical and easily installed cable infrastructure.

• DTP R 211 inputs and output —

• Input: One DTP2 twisted pair input on RJ-45

• Outputs: One HDMI, stereo audio on captive screw

DTP2 T/R 211 • Introduction 2

Page 11

• DTP T 211 inputs and output —

• Inputs: One HDMI, one 3.5 mm stereo mini jack for audio

• Output: One DTP2 twisted pair input on RJ 45

• Supports computer and video resolutions up to 4K/60 @ 4:4:4 — Support of

4K/60 at 4:4:4 chroma sampling requires connection to a matching DTP2 product.

• Stereo audio de-embedding (DTP R 211) — The captive screw stereo output is

selectable for de embedded or pass-through analog audio.

• Analog stereo audio embedding (DTP T 211) — Analog stereo audio signals can be

selectively embedded onto the digital video output signal and transported over DTP. The DTP2 T 211 can be set to pass the embedded digital audio, embed the analog audio, or to automatically embed the analog audio when no digital audio is detected.

• Accepts additional analog stereo audio signals — The DTP2 R 211 accepts stereo

analog audio from a DTP enabled product. The DTP2 T 211 accepts stereo analog audio signals for simultaneous transmission over the same shielded twisted pair cable.

• Supported HDMI 2.0b specification features include data rates up to 18 Gbps,

HDR, Deep Color up to 12 bit, 3D, HD lossless audio formats, and CEC passthrough

• Support for HDR (High Dynamic Range) video — Enables greater contrast range

and wider color gamut by providing the necessary video bandwidth, color depth, and metadata interchange capability for HDR video.

• Supports EDID and HDCP transmission — DDC channels are actively buffered,

allowing continuous communication between source and display.

• Remote power capability — For simplified installation, the transmitter can be remotely

powered by a DTP2-enabled product over the twisted pair connection. It can also be configured to provide power to the connected DTP2 receiver product.

• Supports Consumer Electronics Control (CEC) signal transmission — CEC

control passes through from the transmitter to the receiver.

• Bidirectional RS 232 and IR pass-through for AV device control — Bidirectional

RS 232 control and IR signals can be transmitted alongside the video signal, allowing remote AV devices to be controlled without the need for additional cabling.

• Supports multiple embedded audio formats — Compatible with a broad range of

multi-channel audio signals, providing reliable operation with HDMI sources.

• Front panel USB configuration port — Provides convenient access for information

and firmware updates.

• LED indicators for signal presence, power, and link status — Provide visual

indication of system status for real-time feedback and monitoring of key performance parameters.

• RJ 45 signal and link LED indicators for DTP port — Provide a means for validating

signal flow and operation, allowing quick identification of connectivity issues

• 1-inch high, quarter rack width, metal enclosures — With low profile enclosures,

the transmitter and receiver can be discreetly installed in locations such as behind a plasma or LCD flat-panel display.

• Includes LockIt HDMI cable lacing brackets — LockIt lacing brackets are used to

secure HDMI cables connected to the HDMI input and output connectors, preventing accidental disconnection of the cables.

• Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for

optimal performance.

DTP2 T/R 211 • Introduction 3

Page 12

• Compatible with CATx shielded twisted pair cable — The DTP2R211 and

DTP2T211 fully support a maximum transmission distance of 330 feet (100 meters) for all compatible resolutions when used with CATx shielded twisted pair cable. Shielded twisted pair cabling with solid center conductor sizes of 24AWG or better is recommended for optimal performance.

• External Extron Everlast power supply included (with the transmitter only) —

Provides worldwide power compatibility with high-demonstrated reliability and low power consumption.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty.

DTP2 T/R 211 • Introduction 4

Page 13

Installation and Operation

This section describes the installation and the operation of the DTP2211 transmitter and receiver, including:

• Installation Overview

• Connections

• Operations

Installation Overview

To install and set up the DTP2211 transmitter and receiver:

1. Turn off all equipment and disconnect it from the power source.

2. Mount the transmitter and receiver (optional) on a rack shelf or furniture (see

Mounting the Transmitter or Receiver on page31).

3. Connect an HDMI input source to the DTP2T211 input (see figure2, C on

page6).

4. Connect an HDMI output device to the DTP2R211 HDMI output (see figure3, D

page8).

NOTE: LockIt cable lacing brackets are provided to secure the HDMI cables to the

port to reduce stress on the HDMI connectors and prevent signal loss due to loose cable connections (see Securing the HDMI Connector on page10).

5. Connect the transmitter DTP2 Out RJ-45 port (see figure2, D) to the receiver

DTP2 In RJ-45 port (see figure3, C) using a Twisted Pair Cable.

6. Connect an unbalanced stereo audio source to the 3.5 mm mini stereo input on

the DTP2T211 (see figure2, B) for an analog audio input.

7. Connect a balanced or unbalanced stereo or mono audio device to the

DTP2R211 via the Audio captive screw output (see figure3, F).

8. Set the Audio configuration toggle switch (see figure3,E) on the DTP2R211

to the UP position to de-embed digital audio from the HDMI signal and output it to the captive screw output for analog audio output. Set the Audio configuration toggle switch to the DOWN position for the analog input from the TRS audio port on the Tx unit to be transported simultaneously with the digital embedded HDMI audio and output on the captive screw output (see figure3, F).

9. Connect a serial RS-232 signal, a modulated IR signal, or both into this 3.5mm,

5-pole captive screw Over DTP port for bidirectional RS-232 and IR communication (see figure2, E on the transmitter and figure3, B on the receiver).

10. Connect control devices. Connect your computer to the front panel Configuration

port (see figure8, B on the transmitter and receiver) to configure and control the transmitter and receiver via SIS commands.

11. Power on the output display.

DTP2 T/R 211 • Installation and Operation 5

Page 14

12. In a DTP2 transmitter to DTP2 receiver configuration, set the SEND POWER

AA BB CC DD EE

toggle switch to the UP position on the powered DTP2 device to enable sending remote power to the far end DTP2 device. Set the toggle switch to the DOWN position on the DTP2 device receiving power (see figure8, D on page15).

ATTENTION:

• The DTP2211 device is configured to output power to DTP2 models only. If

connected to a Legacy DTP device, set the toggle switch to the DOWN (OFF) position. Failure to turn the power OFF will damage the connected Legacy DTP device.

• Le DTP2211 est conﬁguré pour fournir une alimentation aux modèles

DTP2 uniquement. S’il est connecté à un autre appareil, veuillez positionner l’interrupteur à bascule sur « DOWN » (OFF). Si l’interrupteur n’est pas positionné sur OFF, vous risquez d’entraîner la défaillance de l’appareil Legacy DTP connecté.

13. Connect power to the transmitter or receiver.

14. Power on the source devices.

After the transmitter, the receiver, and their connected devices are powered up, the system is fully operational. If any problems are encountered, ensure all cables are routed and connected properly.

NOTE: Ensure the video source and display selected for the DDC are properly

connected to the transmitter and receiver pair, and the transmitter, receiver, and display have power applied before power is applied to the video source. If the other devices are not turned on before the video source, the image may not appear.

Connections

Transmitter Rear Panel Connections

POWER 12V

0.8A MAX

AUDIO

INPUTS

Figure 2. DTP2T211 Transmitter Connectors

Power inlet — Plug the included external 12VDC power supply into either this 2-pole

inlet or the power inlet on the receiver (see figure3, A, on page8, and Power

Supply Wiring on page12 to wire the connector).

NOTES:

• One power supply is included with the transmitter and can normally power

both units. Remote power is only available if both the transmitter and the receiver are from the ExtronDTP2 series.

• The power supply can be plugged into either the transmitter or the receiver to

power both units.

• If the internal jumper setting for ground is removed, a DTP2 211 unit cannot

remotely power the other unit, because of ground potential differences. Each unit requires a local power supply (see Internal Settings on page32).

SIG LINK

DTP2 OUT

OVER DTP2

RS-232

Tx Rx Tx RxG

Power inlet

Audio input

HDMI input

DTP2 Output RJ-45 port

Over DTP2 RS-232 and IR port

DTP2 T/R 211 • Installation and Operation 6

Page 15

Audio input (Optional)— (see figure2 on the previous page) Plug an analog audio

Sleeve ( )

Ring (-)

Tip (+)

3.5 mm Stereo Plug Connector

(balanced)

input into the transmitter via this female 3.5mm TRS stereo connector (see Analog

Audio Embedding (Transmitter) on page19).

NOTE: The analog audio input is in addition to the

digital audio that may be embedded in the HDMI input (see the ﬁgure at right to identify the connector tip, ring, and sleeve).

• A mono audio connector consists of the tip and

sleeve.

• A stereo audio connector consists of the tip, ring,

and sleeve.

HDMI input — Connect an HDMI cable between this port and the HDMI output port (or

DVI port, with an appropriate adapter) of the digital video source.

NOTE: See Securing the HDMI Connector on page10 to securely fasten the

HDMI connector to the transmitter and the receiver.

DTP2 Out RJ-45 port — Connect one end of a TP cable to this RJ-45 port on the

transmitter. Ensure the opposite end of this cable is connected to the receiver DTP2 Input RJ-45 port (see figure3, C on the next page).

• Signal LED — This green LED indicates the unit is receiving a TMDS clock signal

on the HDMI input.

• Link LED — This amber LED indicates a valid link is established between the units

on the DTP input and output cable.

ATTENTION:

• Do not connect these devices to a telecommunications or computer data

network.

• Ne connectez pas ces appareils à un réseau de télécommunications ou de

données informatiques.

NOTE: See TP Cable Termination and Recommendations on page11 to

properly wire the RJ-45 connectors and detailed NOTES on page9.

Over DTP2 RS-232 and IR port — Connect a serial RS-232 signal, a modulated IR

signal, or both to this 3.5mm, 5-pole captive screw port for bidirectional RS-232 and IR communication (see RS-232 and IR Connector Wiring on page14 to wire the connector).

DTP2 T/R 211 • Installation and Operation 7

Page 16

Receiver Rear Panel Connections

AA BB CC DD EE FF

Power inlet

POWER 12V

0.8A MAX

OVER DTP2

RS-232

Tx Rx Tx RxG

SIG LINK

DTP2 IN

OUTPUTS

AUDIO

Figure 3. DTP2211 Receiver Connectors

Power inlet — Plug the included external 12VDC power supply into either this 2-pole

inlet or the power inlet on the transmitter (see figure2,A, on page6, and Power

Supply Wiring on page12 to wire the connector).

NOTES:

• One power supply is included with the transmitter and can normally power

both units. Remote power is only available if both the transmitter and the receiver are from the ExtronDTP2 series.

• The power supply can be plugged into either the transmitter or the receiver to

power both units.

• If the internal jumper setting for ground is removed, a DTP2 211 unit cannot

remotely power the other unit, because of ground potential differences. Each unit requires a local power supply (see Internal Settings on page32).

Over DTP2 RS-232 and IR port — Connect a serial RS-232 signal, a modulated IR

signal, or both to this 3.5mm, 5-pole captive screw port for bidirectional RS-232 and IR communication (see RS-232 and IR Connector Wiring on page14 to wire the connector).

DTP2 In RJ-45 port — Connect one end of the TP cable from the transmitter output

to this RJ-45 port. Ensure the opposite end of this cable is connected to the transmitter DTP2 Output RJ-45 port (see figure2, D).

• Signal LED — This green LED indicates the unit is receiving a valid signal on the

DTP In port.

• Link LED — This amber LED indicates a valid link is established between the units

on the DTP input and output cable.

NOTE: See TP Cable Termination and Recommendations on page11 to

properly wire the RJ-45 connectors and detailed NOTES on page11.

HDMI output — Connect a display with an HDMI input port (or DVI input port, with an

appropriate adapter) to display the transmitted digital image.

NOTE: See Securing the HDMI Connector on the next page to securely fasten

the HDMI connector to the transmitter and the receiver.

Audio configuration toggle switch —

• Set the toggle switch to the UP position to de-embed digital audio from the HDMI

signal and output it to the captive screw output for analog audio output.

Over DTP2 RS-232 and IR port

DTP2 In RJ-45 port

HDMI output

Audio configuration toggle switch

Audio output

NOTE: If the HDMI source audio is in a multi channel format, the audio cannot

be extracted on the receiver. If the toggle switch is set to the UP position, the analog audio output will be muted, but the audio still passes through the HDMI output.

DTP2 T/R 211 • Installation and Operation 8

Page 17

• Set the toggle switch to the DOWN position for the analog input from the TRS audio

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Do not tin the wires!

port on the Tx unit to be transported simultaneously with the digital embedded HDMI audio and output on the captive screw output (see figure3, E on page8) (see HDMI Audio De-embedding (Receiver) on page19).

Audio output — This 5-pole, 3.5mm captive screw connector outputs the transmitted,

unamplified, line level analog audio. Connect a balanced or unbalanced stereo or mono audio device, such as an audio amplifier or powered speakers (see figure3).

See figure4 to properly wire a captive screw output connector. Use the supplied tie-wrap to strap the audio cable to the extended tail of the connector.

Figure 4. Captive Screw Connector Wiring for Stereo Audio Output

NOTE: See the Attention notiﬁcations before wiring the captive screw connector.

ATTENTION:

• For unbalanced audio, connect the sleeves to the ground contact. DO NOT

connect the sleeves to the negative (–) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS

connecter les manchons aux contacts négatifs (–).

• Do not tin the wire leads before installing into the connector. Tinned wires are

not as secure in the connector and could be pulled out.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les

câbles étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être tirés.

• The length of the exposed wires in the stripping process is important. The

ideal length is 3/16inch (5mm). Any longer and the exposed wires may

touch, causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est importante lorsque l’on entreprend de

les dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont trop longs, les câbles exposés pourraient se toucher et provoquer un courtcircuit. S’ils sont trop courts, ils peuvent être tirés facilement, même s’ils sont correctement serrés par les borniers à vis.

DTP2 T/R 211 • Installation and Operation 9

Page 18

Securing the HDMI Connector

Follow these instructions to secure the input and output connectors to the transmitter and receiver with the LockIt HDMI lacing bracket provided:

Plug the HDMI cable into the rear panel connection.

Loosen the HDMI connection mounting screw from

the rear panel enough to allow the LockIt lacing bracket to be placed over it. The screw does not have to be removed.

Place the LockIt lacing bracket on the screw and

against the HDMI connector, then tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connector

mounting screw. The shield it fastens to is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du

connecteur HDMI. Le blindage auquel elle est attachée est très fin et peut facilement être dénudé.

Loosely place the included tie wrap around the

HDMI connector and the LockIt lacing bracket as shown.

While holding the connector securely against the lacing bracket, tighten the tie wrap,

then remove any excess length.

DTP2 T/R 211 • Installation and Operation 10

Page 19

TP Cable Termination and Recommendations

Side

Pair Wires

Pins:

The TIA/EIA T 568B wiring standard is detailed in figure5. Use this standard to terminate TP cables with RJ-45 connectors.

Wire color

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

RJ-45 Connector

TIA/EIA T

568 B

12345678

Insert

Twisted

Figure 5. TP Cable Termination

ATTENTION:

• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201

cable to link the XTP products or with DTP2 transmitters or receivers. The DTP2211 does not work properly with these cables.

• N’utilisez pas le câble audiovisuel Skew-Free UTP version améliorée UTP23SF-4

Extron ou le câble STP201 pour relier les produits XTP à des émetteurs ou récepteurs DTP2. Le DTP2 211 ne fonctionne pas correctement avec ces câbles.

Supported cables — The DTP2211 transmitter and receiver are compatible with CAT 6a, and CAT 7 shielded

twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Cable recommendations — Extron recommends using the following practices to achieve full transmission distances up

to 330feet (100meters) and reduce transmission errors.

• Use the following Extron XTPDTP24SF/UTP cables and DTP 24 connectors for the

best performance:

• XTPDTP24/1000 Non-Plenum 1000feet (305meters) spool

• XTPDTP24P/1000 Plenum 1000feet (305meters) spool

• XTPDTP24 Plug Package of 10

• If not using XTPDTP24 cable, at a minimum, Extron recommends 24AWG, solid

conductor, STP cable with a minimum bandwidth of 400MHz.

• Terminate cables with shielded connectors to the TIA/EIAT568B standard.

• Use no more than two pass-through points, which may include patch points, punch

down connectors, couplers, and power injectors. If these pass-through points are required, use CAT6 or 6a shielded couplers and punch down connectors.

NOTES: When using CAT 6a and CAT 7 cable in bundles or conduits, consider the

following:

• Do not exceed 40% fill capacity in conduits.

• Do not comb the cable for the first 65feet (20meters), where cables are straightened,

aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

DTP2 T/R 211 • Installation and Operation 11

Page 20

Power Supply Wiring

A 12VDC, 1.5Apower supply is provided with the DTP2211 transmitter. Follow these instructions to wire the 2-pole captive screw connector to your power supply:

CAUTION: Risk of minor personal injury: ATTENTION : Risque de blessuremineure :

• The DC output cables must be kept separate from each other while the power

supply is plugged in. Remove power before wiring.

• Les câbles de sortie CC doivent être séparés les uns des autres tant que la

source d’alimentation est branchée. Coupez l’alimentation avant d’effectuer les raccordements.

ATTENTION:

• Do not connect any external power supplies until you have read the ATTENTION

notifications on the next page.

• Veuillez lire les encadrés « Attention » sur la page suivante avant de brancher une

source d’alimentation externe.

NOTES:

• One power supply is included with the transmitter and can normally power both

units, if they are both from the Extron DTP2 series.

• If the ground jumper (JMP 2) is Open (Off), (see Internal Settings on page32)

because of ground potential differences, one DTP2211 unit cannot remotely power the other unit. Each unit requires a local power supply.

See figure6 to wire the captive screw connector and secure the power cord to the extended tail of the connector.

Smooth

SECTION A–A

Ridges

3/16"

(5 mm) Max.

POWER

12V

--A MAX

Figure 6. Power Connector Wiring

1. Cut the DC output cord to the length needed.

2. Strip the jacket to expose 3/16inch (5mm) of the conductors.

3. Slide the leads into the supplied 2-pole captive screw plug and secure them, using a

small screwdriver.

4. To verify the power cord polarity before connecting the plug, connect the power supply

with no load and check the output with a voltmeter.

5. Use the supplied tie wrap to strap the power cord to the extended tail of the connector.

DTP2 T/R 211 • Installation and Operation 12

Page 21

ATTENTION:

• Always use a power supply supplied and or specified by Extron. Use of an

unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute certification de conformité réglementaire, et peut endommager la source d’alimentation et l’unité.

• If not provided with a power supply, this product is intended for use with a UL

Listed power source marked “Class 2” or “LPS” rated 12 VDC, 1.5 A minimum.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être utilisé

avec une source d’alimentation certifiée UL de classe 2 ou LPS avec une tension nominale de 12 Vcc, 1,5 A minimum.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to building structure or similar structure.

• Cette installation doit toujours être conforme aux dispositions applicables du Code

américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie 1, section 16. La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the

power supply and the unit. The ridges on the side of the cord (see ﬁgure6 on the previous page) identify the power cord negative lead.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du cordon (voir ﬁgure6 sur la page précédente) permettent de repérer le pôle négatif du cordon d’alimentation.

• To verify the polarity before connection, plug in the power supply with no load and

check the output with a voltmeter.

• Pour vériﬁer la polarité avant la connexion, brancher l’alimentation hors charge et

mesurer sa sortie avec un voltmètre.

• The length of the exposed (stripped) copper wires is important. The ideal length is

3/16inch (5mm). Longer bare wires can short together. Shorter wires are not as

secure in the connectors and could be pulled out.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont trop longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont trop courts, ils peuvent être tirés facilement, même s’ils sont correctement serrés par les borniers à vis.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling

spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation

dans les espaces d’aération ou dans les cavités murales.

• Remote power is intended for indoors use only. No part of a network that uses

remote power can be routed outdoors.

• L’alimentation à distance est exclusivement réservée à un usage en intérieur. Un

réseau utilisant une alimentation à distance ne peut pas être routé en extérieur.

DTP2 T/R 211 • Installation and Operation 13

Page 22

RS‑232 and IR Connector Wiring

IR Device

RS-232 Device

OVER DTP

See figure7 to wire the 5-pole RS-232 and IR communication connector.

TxRx

Gnd

RxTx RxTxG

RS-232 IR

RxTx

Gnd

Figure 7. RS-232 Connector Wiring

Use a female 9-pin D connector to bare wire RS-232 cable or a universal control cable (UC50’ or UC100’) to connect your computer or control system to the Over DTP2 port.

1. Wire the unterminated end of the RS-232 cable to the first three pins on the connector,

starting at the left of the 5-pole captive screw plug as described below:

a. Connect the transmit wire from the RS-232 device into the Rx pin of the DTP2211. b. Connect the receive wire from the RS-232 device into the Tx pin of the DTP2211. c. Connect the ground wire from the RS-232 device into the G pin of the DTP2211.

2. Wire the unterminated end of the IR cable to the third, fourth, and fifth pins of the 5-pole

captive screw plug as shown in figure7.

a. Connect the transmit wire from the IR device into the Rx pin of the DTP2211. b. Connect the receive wire from the IR device into the Tx pin of the DTP2211. c. Connect the ground wire from the IR device into the G pin of the DTP2211.

3. Plug the 5-pole connector into the Over DTP2 port on the rear panel of the transmitter

or receiver.

4. Connect the other end of the cable to the appropriate computer or control system port.

NOTES:

• The RS-232 and IR connectors share the ground pole and the data from both can

be transmitted simultaneously.

• The IR Tx and Rx line pair and the RS-232 Tx and Rx line pair must each cross

once between this connector and the source or destination.

• The length and preparation of exposed wires is important (see the ATTENTION

notifications on the previous page for details).

DTP2 T/R 211 • Installation and Operation 14

Page 23

Operations

DTP2 T 211 Front Panel DTP2 R 211 Front Panel

AA BB CC DD AA BB CC DD

Front Panel Features

CONFIG

STATUS

INPUT

LINK

OUTPUT

SEND

POWER

OFF

CONFIG

DTP2 T 211

STATUS

INPUT

LINK

OUTPUT

SEND

POWER

OFF

DTP2 R 211

Figure 8. Front Panels of the DTP2211 Transmitter and Receiver

Power LED — Lights when the unit is receiving power, either locally or remotely (over the

DTP cable).

Configuration port — Using a USB cable, plug a PC into the transmitter or receiver

via this front panel mini-USB connector for firmware updates (see Connecting to the

Front Panel USB Port on page17).

Status LEDs

• Input Signal — Lights when the unit is receiving a TMDS clock signal on the HDMI

input (transmitter), or any valid signal on the DTP In connector (receiver).

• DTP Link Status — Lights when a transmitter or receiver detect a sink signal from

a connected DTP device.

• DTP Output Signal — Lights when the transmitter or receiver establish

communication with the connected DTP2 or Legacy DTP device.

NOTE: The front panel LEDs are tied to the rear panel LEDs on the DTP2 port.

SEND POWER toggle switch — In a DTP2 transmitter to DTP2 receiver configuration,

set the toggle switch to the UP (SEND POWER) position on the powered DTP2 unit to enable sending remote power to the far end. Set the toggle switch to the DOWN (OFF) position on the DTP2 unit receiving power (see figure9 on the next page for toggle switch configuration).

ATTENTION:

• The DTP2211 device is configured to output power to DTP2 models only. If

connected to a Legacy DTP device, set the toggle switch to the DOWN (OFF) position. Failure to turn the power OFF will damage the connected Legacy DTP device.

• Le DTP2211 est conﬁguré pour fournir une alimentation aux modèles

NOTE: DTP2 transmitters and receivers are compatible with Legacy DTP products.

However, Remote Power must be configured properly. Failure to do so will result in damage to the units.

DTP2 T/R 211 • Installation and Operation 15

Page 24

Extron

DTP Endpoint Connected to a DTP2 Endpoint

Power Supply

DTP HDMI 4K 330 Tx

Transmitter

DTP HDMI 330 Tx

No Remote Power

CATx Cable

up to 330' (100 m)

Extron DTP2 R 211

Receiver

STATUS

CONFIG

INPUT

LINK

OUTPUT

SEND

POWER

OFF

SEND

POWER

OFF

DTP2 R 211

Local

Power Supply

Local

Power Supply

OFF

SEND

POWER

OFF

Local

POWER

OFF

DTP2 T 211

No Remote Power

CATx Cable

up to 330' (100 m)

Extron DTP HDMI 4K 330 Rx

Receiver

OVER DTP

RS-232

TxRx Tx RxG

Power Supply

DTP HDMI 330 Rx

Local

Extron DTP2 T 211

Transmitter

STATUS

CONFIG

Power Supply

INPUT

LINK

OUTPUT

DTP2 Endpoint Connected to a DTP2 Endpoint

OFF ON

SEND

INPUT

LINK

OUTPUT

SEND

POWER

Extron

OFF

Direction of

Remote Power

OFF

DTP2 T 211

CATx Cable

up to 330' (100 m)

DTP2 R 211

Receiver

STATUS

CONFIG

INPUT

LINK

OUTPUT

Extron DTP2 T 211

Transmitter

STATUS

CONFIG

SEND

POWER

SEND

POWER

OFF

DTP2 R 211

ON OFF

SEND

INPUT

LINK

OUTPUT

SEND

POWER

OFF

POWER

OFF

DTP2 T 211

Direction of

Remote Power

CATx Cable

up to 330' (100 m)

Extron DTP2 R 211

Receiver

CONFIG

Extron DTP2 T 211

Transmitter

STATUS

CONFIG

Local

Figure 9. Send Power Toggle Switch Configuration

DTP2 T/R 211 • Installation and Operation 16

Local

Power Supply

SEND

POWER

STATUS

SEND

INPUT

POWER

LINK

OUTPUT

OFF

DTP2 R 211

Page 25

Connecting to the Front Panel USB Port

Use the mini Type B USB port on the front panel (see figure10) to connect the transmitter or receiver to a host computer to configure the unit with SIS commands.

1. Connect a USBA to miniB cable between the front panel USB Config port and a

USBport of the PC.

WiFi

1234

STATUS

INPUT

CONFIG

LINK

OUTPUT

DTP2 T 211 Transmitter

Mini Type B

USB

POWER

FAR RND

OFF

USB Cable

DTP2 T 211

Type A

USB

USB Ports

Figure 10. Connecting a PC to the DTP2T211 Front Panel USB Port

If this is the first time the DTP2211 has been connected to the PC, the Found New

Hardware Wizard opens (see figure11).

The first screen offers to connect to Windows Update to search the web for the appropriate driver needed for the USB port to communicate with the DTP2211. This is not necessary if the USB driver is already on your PC.

Figure 11. Found New Hardware Wizard Welcome Screen

2. Click on the appropriate radio button (see figure11):

• Select the Yes, this time only radio button (1) if you want your computer to

connect to Windows Update only this one time.

DTP2 T/R 211 • Installation and Operation 17

Page 26

• Select Yes, now and every time I connect a device (see figure11, 2 on the

previous page) if you want the computer to automatically connect to Windows Update to search the web every time the transmitter or receiver is connected to this USB port.

• Select No, not this time (3) if you do not want the computer to connect to

Windows Update to search the web at this time (for example, if the driver is already on your computer).

3. Click Next (4).

The next screen of the Wizard opens:

Figure 12. Installing the Software Automatically

4. Select Install the software automatically (Recommended) radio button (see

figure12,1 above).

5. Click Next (2).

NOTE: You do not need to insert an installation disc.

The PC locates the driver needed and installs it in the correct location on the hard drive.

6. When the Completed screen appears, click Finish to close the wizard.

NOTE: The wizard opens only on the first occasion you connect the transmitter

or receiver to that USB port. The wizard reappears if you connect the unit to a different USB port or if you connect a different piece of equipment, requiring a different driver, to the same USB port.

7. Configure the transmitter or receiver as required using SIS Commands (see Remote

Control starting on page20).

Resetting

Use the SIS command to reset the transmitter or receiver to its factory default settings (see

Reset on page23).

DTP2 T/R 211 • Installation and Operation 18

Page 27

Analog Audio Embedding (Transmitter)

Analog audio on the 3.5 mm input on the transmitter functions in two modes, which can be configured via SIS commands (see Audio Input Configuration (Tx only) on page22):

• Analog audio over DTP — Standard analog audio over DTP is digitized and

transported simultaneously with the embedded digital audio on the HDMI signal.

• Embedding the analog audio input — The analog input signal is converted to 16-bit

2.0 LPCM, with 48 kHz sampling frequency, and embedded onto the HDMI signal. Configure the analog audio embedding via SIS commands with three options:

• Auto (default) — The original embedded digital audio passes. If audio packets are

not detected, analog audio is embedded.

• Force analog audio embedding — Analog audio is always embedded.

• No embedding — Existing embedded digital audio passes.

HDMI Audio De‑embedding (Receiver)

Using the rear panel toggle switch (see figure3, E on page8), the DTP2 211 receiver can be configured to:

• UP — HDMI digital audio pass-through and HDMI audio is de-embedded.

• DOWN (default) — HDMI digital audio pass-through and analog audio over DTP2.

NOTE: Whether the audio configuration switch is UP or DOWN, the embedded digital

audio on the HDMI signal remains intact.

DTP2 T/R 211 • Installation and Operation 19

Page 28

Remote Control

Use Simple Instruction Set (SIS) commands to configure the DTP2211 transmitter and receiver. This section provides information about using those commands. The following topics are discussed:

• Introduction to SIS

• Symbols Used in this Guide

• Command and Response Table for SIS Commands

• Downloading and Updating Firmware

Introduction to SIS

The DTP2211transmitter and receiver accept SIS commands from a host device such as a computer running the Extron DataViewer utility or other control system. The host device can be connected to the Config port on the front panel (see Connecting to the Front Panel

USB Port on page17).

SIS commands consist of strings (one or more characters per command field). Upper and lower case characters can be used interchangeably. Commands do not require any special characters to begin or end the command string. Each response from the DTP2211 transmitter and receiver ends with a carriage return and a line feed (CR/LF=]), which signals the end of the response character string.

When the transmitter or receiver is first switched on, it sends the message:

Error Messages

E10 — Invalid command E13 — Invalid parameter

Timeout

Pauses of 10seconds or longer between command ASCII characters result in a timeout. The command operation is aborted with no other indication.

• Vx.xx is the firmware version number.

• 60‑xxxx‑xx is the part number of the device.

DTP2 T/R 211 • Remote Control 20

Page 29

Symbols Used in this Guide

Space

When programming in the field, certain characters are most conveniently represented by their hexadecimal rather than their ASCII values. The table below shows the hexadecimal

equivalent of each ASCII character:

ASCII to Hex Conversion Table

Figure 13. ASCII to Hex Conversion Table

Symbol Definitions

] = Carriage return with line feed

| or } = Pipe character or carriage return (no line feed) can be used interchangeably.

• = Space character

W or E = W or Escape key can be used interchangeably.

X! = Input or Output X@ = Verbose mode

0 = Clear/none 1 = Verbose mode (default) 2 = Tagged responses for queries 3 = Verbose mode and tagged responses for queries

•

X# = Text string of up to 24 characters

Default = DTP2‑T‑211 or DTP2‑R‑211 Alphanumeric characters and hyphens only No distinction between upper and lower case No spaces First character must be a letter and the last character cannot be a hyphen

X$ = Firmware version to the second decimal place X% = Audio input

0 = Auto (default) 1 = Digital 2 = Analog

X^ = Remote power

0 = No remote power (Off) 1 = DTP2 48 VDC (On)

X* = Audio toggle switch

1 = UP — Digital audio pass-through 2 = DOWN — Digital to analog audio extraction

DTP2 T/R 211 • Remote Control 21

Page 30

Command and Response Table for SIS Commands

Command ASCII Command

(host to unit)

Audio Input Configuration (Tx only)

Set audio input format

View audio input format

I X%

IAFMT

AFMT

}

Verbose mode 2/3

KEY:

= Audio input 0 = Auto (default); 1 = Digital; 2 = Analog.

Audio Toggle Switch Status (Rx only)

View audio toggle switch status

KEY:

= Audio toggle switch 1 = UP — Digital audio pass-through; 2 = DOWN — Digital to analog audio extraction.

Verbose mode 2/3

STAT

}

DTP2 Remote Power

View input/output remote power

KEY:

= Remote 0 = No remote power (Off); 1 = DTP2 48 VDC (On).

Verbose mode 2/3

RPWR

}

Verbose Mode

Set verbose mode

E X@ CV

}

Response

(unit to host)

]

AfmtI

]

AfmtI

Stat

Rpwr

Vrb X@

Additional Description

X%: 0 = default.

View remote power setting on DTP2 in and out.

X@: 1 = default.

View verbose mode

KEY:

View Firmware Information

= Verbose mode 0 = Clear/none; 1 = Verbose mode (default); 2 = Tagged responses for queries;

3 = Verbose mode and tagged responses for queries.

Query firmware version

Query firmware version w/ build

Query detailed firmware version

Query build and any special build text

KEY:

= Firmware version to the second decimal place.

Q/q

*Q/q

0Q/q

20Q/q

}

]

x.xx]

x.xx.xxxx]

]

Firmware build with 2 decimals.

DTP2 T/R 211 • Remote Control 22

Page 31

Command ASCII Command

(host to unit)

Unit Name

Set unit name Set unit name to factory

E X#CN E•CN

}

default Query unit name

}

Verbose mode 2/3

Response

(unit to host)

Ipn•X# Ipn•DTP2‑T‑211

Ipn•DTP2‑R‑211

Ipn•X#

]

Additional Description

] ]

KEY:

= Text string of up to 24 characters

(Default = DTP2‑T‑211 or DTP2‑R‑211). Alphanumeric characters and hyphens only No distinction between upper and lower case No spaces First character must be a letter and the last character cannot be a hyphen

View Device Information

Query part number

Query model name

Query model description

Reset

N/n

Verbose mode 2/3

1I/i

Verbose mode 2/3

2I/i

Verbose mode 2/3

ZXXX

}

60‑1631‑52 Pno•60‑1631‑52

60‑1631‑53 Pno•60‑1631‑53

DTP2•T•211

Inf01*DTP2•T•211

DTP2•R•211

Inf01*DTP2•R•211

DTP2•HDMI•4K60•Transmitter

Inf02*DTP2•HDMI•4K60•Transmitter

DTP2•HDMI•4K60•Receiver

Inf02*DTP2•HDMI•4K60•Receiver

]

Zpx

]

DTP2T211

DTP2R211

DTP2T211

DTP2R211

DTP2T211

]

DTP2R211

DTP2 T/R 211 • Remote Control 23

Page 32

Downloading and Updating Firmware

Firmware for the DTP2211 products can be upgraded using Extron Firmware Loader and a PC. Both Extron Firmware Loader and upgraded firmware for the DTP2211 can be downloaded at www.extron.com.

NOTE: Upgrading the firmware does not overwrite the current configuration.

Downloading Extron Firmware Loader

1. On the Extron website, mouse over the Download tab (see figure14, 1).

Figure 14. Locating Firmware Loader Software

2. Click on Software link in the drop-down menu(2). The Software page opens.

Figure 15. Software Page with Alphabetic Navigation Bar

3. On the bottom of the page, click on the Flink (see figure15, 1).

4. Locate Firmware Loader (see figure16 on the next page).

DTP2 T/R 211 • Remote Control 24

Page 33

Figure 16. Firmware Loader Software

5. Click Release Notes (see figure16,1) to see the issues that have been addressed by

the latest update.

6. Click the Download link on the right (2). Note where the file is saved.

Installing Firmware Loader

1. Once Firmware Loader has been downloaded, run the .exe file from the save

location. The Installation Wizard window opens.

2. Follow the instructions on the Installation Wizard screens to install Firmware

Loader on the computer. The installation creates the necessary subfolders of C:\ Program Files and the necessary groups. It places the appropriate files into the

correct group folders:

• Folder — C:\Program Files\Extron\FWLoader

Downloading Firmware to a PC

1. Power on a computer connected to the same network as the transmitter or receiver.

2. On the Extron website, mouse over the Download tab in the menu bar along the top of

the page (see figure17,1).

Figure 17. Locate Firmware for DTP2211 Transmitter or Receiver

3. Click Firmware in the drop-down menu (2).

The Firmware page opens (see figure18 on the next page).

DTP2 T/R 211 • Remote Control 25

Page 34

Figure 18. Firmware Page with Alphabetic Navigation Bar

4. Click the letter D from the alphabetic navigation bar (see figure18, 1).

5. Scroll down the page until you find the firmware for the transmitter or the receiver.

6. Click Release Notes for more information about the program (optional).

7. Click the Download link on the right.

8. Follow the on-screen instructions to download the firmware. Make a note of where the

firmware file is stored on the PC.

ATTENTION:

• The extension of the firmware file must be .s19. Opening a file with an

incorrect extension may cause the device to stop functioning.

• L’extension du fichier firmware doit être .s19. Si un fichier est ouvert avec une

mauvaise extension, l’appareil peut arrêter de fonctionner.

Updating Firmware on a DTP2211 Device

1. Download the latest version of the firmware to your PC.

2. Connect the PC to the DTP2211 device via the front panel USB port (see Connecting

to the Front Panel USB Port on page17) of the transmitter or receiver.

3. Open the Firmware Loader via the Firmware Loader icon installed during the

download (optional) or your desktop Start menu by making the following selections:

Start > All Programs > Extron Electronics > Firmware Loader > Firmware Loader

The Firmware Loader window opens. The Add Device... window opens in front (see figure19).

Figure 19. Opening Firmware Loader

4. In the Add Device window, select the DTP2211 from the Device Names drop-down

menu.

DTP2 T/R 211 • Remote Control 26

Page 35

5. From the Connection Method drop-down menu, select USB.

6. Additional options appear. Make the appropriate selections for the USB connection.

• Only the Extron USB Device_0 option is available on the Available Devices

menu. Make sure that it is selected.

7. Click Connect (see figure20, 1). If the connection is successful, the unit name is

displayed in green in the Connected Device section, followed by a check mark (2).

DTP2 T 211

DTP2T211\dtp2t211_A_v1.00_081518.S19

Figure 20. Add Device Window

8. Click the Browse button (3) in the New Firmware File (Optional) section.

9. In the Open window, locate and double-click the new firmware file, which has an .s19

extension.

NOTE: The file listed in the File name field is an example only and not an actual

firmware file for the devices.

DTP2 T 211

DTP2T211_v1.00_051818.S19

DTP2T211_A_v1.00_051818.S19

Figure 21. Open Window for Firmware Selection

DTP2 T/R 211 • Remote Control 27

Page 36

ATTENTION:

• The extension of the firmware file must be .s19. Opening a file with an

incorrect extension may cause the device to stop functioning.

• L’extension du fichier firmware doit être .s19. Si un fichier est ouvert avec une

mauvaise extension, l’appareil peut arrêter de fonctionner.

NOTE: The original factory-installed firmware is always available on the DTP2211

unit. If the attempted firmware upload fails for any reason, the unit reverts to the factory version.

On the Add Device... window, the path to the new firmware file is displayed in the

Path field (see figure22,

DTP2 T 211

DTP2T211\dtp2t211_A_v1.00_081518.S19

Figure 22. Path to New Firmware File on the Add Device Window

10. If this is the only device uploading firmware, click Add (2). The device name is

added to the Device section of the Firmware Loader window and the Add Device window closes.

If firmware is uploading to multiple devices, do the following:

a. Click Add Next (3). The first device is added to the Device section of the

Firmware Loader window, and the Add Device... window remains open.

b. For each additional device that needs to be added to the Firmware Loader

window, repeat steps 4 through 9, then click Add Next(3).

c. For the last device, click Add (2), instead of Add Next (3), to add the device and

close the Add Device... window.

DTP2 T/R 211 • Remote Control 28

Page 37

DTP2 T 211 dtp2t211_A_v1.00.00...

60-1631-52

1.00.001

Extron USB Devi... Connected

Figure 23. Firmware Loader Screen with a DTP2 T 211 Added

11. To remove a device from the Device section, do the following: a. Click on the names of the devices to be deleted, highlight them (see figure23, 1). b. Click on the Edit tab (see figure24, 1) in the menu bar at the top of the page. c. Select Remove Selected Device(s) (2) from the Edit menu.

Figure 24. Firmware Loader Edit Menu

d. Select Remove All Devices (3) from the Edit menu to remove all devices.

12. Click Begin (see figure23, 2).

The following indicators show the progress of the update:

• The Transfer Time section shows the remaining and elapsed time for the

update (see figure25, 1 on the next page).

• The Total Progress section displays a progress bar with Uploading...

above it (2).

• In the Device section, the Progress column displays an incrementing

percentage and another progress bar (3).

• The Status column displays Uploading...(4).

DTP2 T/R 211 • Remote Control 29

Page 38

DTP2 T 211

60-1631-52 1.00.001

dtp2t211_A_v1.00.00...

Extron USB Devi...

3 4

Uploading...

Connected

Figure 25. Firmware Upload in Progress

The upload is complete when the Remaining Time field shows 00.00.00, (see figure26, 1) the Progress column shows 100% (2), and Completed is displayed above the progress bar (3) and in the Status column (4).

DTP2 T 211

60-1631-52 1.00.001

2 4

Extron USB Devi... Completeddtp2t211_A_v1.00.00...

Figure 26. Firmware Upload Complete

13. Close the Firmware Loader window when the upload is complete.

DTP2 T/R 211 • Remote Control 30

Page 39

Reference Information

This section provides procedures for mounting the DTP2211transmitter and receiver and disconnecting the ground between them.

• Mounting the Transmitter or Receiver

• Internal Settings

Mounting the Transmitter or Receiver

ATTENTION: Risk of property damage: ATTENTION : Risque de dommages matériels:

• Installation and service must be performed by authorized personnel only.

• L’installation et la maintenance du système doivent être exclusivement effectuées

par le personnel autorisé.

• Avoid ground potential differences between the transmitter and receiver installation

sites, which can lead to equipment damage or a missing or unstable picture. If a potential difference cannot be avoided, remove the ground connection between the units and locally power both units (see Internal Settings on page32).

• Évitez les différences de potentiel de mise à la terre entre les sites d’installation

d’émetteur et de récepteur de commutation, qui pourraient endommager l’équipement ou rendre l’image invisible ou irrégulière. Si une différence de potentiel ne peut être évitée, enlevez la connexion de mise à la terre entre les unités et alimentez les deux unités localement (voir Internal Settings à la page32).

The 1-inch high, quarter rack width, 6-inches deep transmitter and receiver can be placed on a table, mounted in a rack, or mounted under a desk or table. The receiver can also be mounted on a projector bracket.

Tabletop Use

Affix the included rubber feet to the bottom of the unit and place it in any convenient location.

Mounting kits

Mount the unit using the optional compatible mounting kit listed on the Extron website, in accordance with the directions included with the kit. The devices are compatible with the Extron Half Rack shelf system HRB109, Extron UTS under the table shelf system, Extron rack shelves RSU126, and MBU125 under the table shelf brackets.

For rack mounting, see UL Rack-Mounting Guidelines on the next page.

DTP2 T/R 211 • Reference Information 31

Page 40

UL Rack‑Mounting Guidelines

The following Underwriters Laboratories (UL) requirements pertain to the installation of the unit into a rack.

• Elevated operating ambient temperature — If installed in a closed or multi-unit rack

• Reduced air flow — Installation of the equipment in a rack should be such that the

• Mechanical loading — Mounting of the equipment in the rack should be such that a

• Circuit overloading — Consideration should be given to the connection of the

• Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment

Internal Settings

assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consider installing the equipment in an environment compatible with the maximum ambient temperature (TMA = +122°F, +50°C) specified by Extron.

amount of air flow required for safe operation of the equipment is not compromised.

hazardous condition is not achieved due to uneven mechanical loading.

equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (such as use of power strips).

ATTENTION:

• Use electrostatic discharge (ESD) precautions (be electrically grounded) when

making connections.

• Prenez des précautions contre les décharges électrostatiques (soyez

électriquement relié à la terre) lorsque vous effectuez des connexions.

• Avoid ground potential differences between the transmitter and receiver installation

sites, which can lead to equipment damage or a missing or unstable picture. If a potential difference cannot be avoided, remove the ground connection between the units and locally power both units.

• Évitez les différences de potentiel de mise à la terre entre les sites d’installation

There are two internal jumpers used to configure the DTP2 ground lift and remote power. The jumpers have the following numbering scheme and function:

Jumper Function Jumper

Ground Lift:

• Rx — J2

• Closed — Ground is NOT lifted (default)

• Open — Ground is lifted

• Tx — J9

48 VDC Remote Power:

• On — Remote power is distributed (default)

• Off — Remote power is disabled

• Rx — J3

• Tx — J12

Pins 1 and 2

Closed

Jumper

Pins 2 and 3

Open

Off

DTP2 T/R 211 • Reference Information 32

Page 41

NOTES:

Rear Panel

(Rear)

• If the ground jumper is Open, a DTP2 211 unit cannot remotely power the other

unit, because of ground potential differences. Each unit requires a local power supply.

• If the 48 VDC remote power jumper is Off, DTP2 211 unit cannot remotely power

the other unit. Each unit requires a local power supply.

Follow these instructions to gain access to the jumpers:

1. Disconnect any cables and remove the transmitter and receiver from the rack or other

installation option.

2. Remove and retain the screws securing the covers to the transmitter and receiver. Slide

the covers forward slightly and lift them off both units (see figure27).

• Eight screws, three on each side and two on top

Cover Screw (8 Plcs)

Figure 27. Opening the Transmitter and Receiver

3. Locate (see figure28), lift jumper off pins 1 and 2, and place on pins 2 and 3 (see

figure27).

J9 J12

Transmitter

Receiver

Figure 28. Jumper Locations

4. Reinstall the covers on both units, securing them in place with the screws removed in

step2.

5. Reinstall both units in their racks or other installation option (see Mounting the

Transmitter or Receiver on page31).

6. If shielded cable is used, disconnect the cable shield from the connector at either

end of the cable.

7. Obtain a second 18watt power supply (one power supply is provided with the

transmitter and normally powers both units), and locally power both units (see Power

Supply Wiring on page12).

DTP2 T/R 211 • Reference Information 33

Page 42

ATTENTION:

• If not provided with a power supply, this product is intended to be supplied

by a UL Listed power source marked “Class 2” or “LPS,” rated 12VDC, 1.5A minimum.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être

alimenté par une source d’alimentation certifiée UL de classe 2 ou LPS, avec une tension nominale 12 Vcc, 1,5 A minimum.

• Always use a power supply provided by or specified by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par

Extron. L’utilisation d’une source d’alimentation non autorisée annule toute certiﬁcation de conformité réglementaire, et peut endommager la source d’alimentation et l’unité.

DTP2 T/R 211 • Reference Information 34

Page 43

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Extron Electronics 1230 South Lewis Street Anaheim, CA 92805 U.S.A.

Europe:

Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands

Africa:

Extron South Africa South Tower 160 Jan Smuts Avenue Rosebank 2196, South Africa

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modiﬁcations were made to the product that were not authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: 714.491.1500 or 800.633.9876 Asia: 65.6383.4400

Europe: 31.33.453.4040 or 800.3987.6673 Japan: 81.3.3511.7655 Africa: 27.11.447.6162 Middle East: 971.4.299.1800

Asia:

Extron Asia Pte Ltd 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363 Singapore

China:

Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China

Japan:

Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan

Middle East:

Extron Middle East Dubai Airport Free Zone F13, PO Box 293666 United Arab Emirates, Dubai

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or ﬁtness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876