Extron electronics DPH 101 User Manual

DPH 101 • User Guide

The Extron DPH 101 DisplayPort to HDMI active adapter equalizes incoming DisplayPort
sources up to 15 feet (4.5 meters) at the input to compensate for signal loss. The DPH 101
then reconditions the signal, ensuring signal integrity up to an additional 15 feet (4.5 meters)
from the output to the connected HDMI device.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause interference; the user
must correct the interference at his own expense.

NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables must be used to ensure

compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related
topics, see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

Specifications Availability

Product specications are available on the Extron website, www.extron.com.

Features

• Provides connectivity between Type 2 enabled, 4K-capable Dual-Mode DisplayPort equipped sources and HDMI sink

devices

• Equalizes incoming DisplayPort signals up to 15 feet (4.5 meters) to compensate for signal loss

• Reconditions HDMI signals at the output to ensure signal integrity up to 15 feet (4.5 meters) to the connected HDMI device

• Supports computer video to 2560x1600, HDTV 1080p/60 Deep Color, and 4K resolutions

• Passes EDID information from HDMI display to the source

• HDCP compliant

• Supports data rates of 3.4 Gbps per color (10.2 Gbps total)

• LED indicator for signal presence and power — Provides visual indication of system status for real-time feedback and

monitoring of key performance parameters

• Shares power supply with another Extron product or optional external power supply

1

DPH 101 • User Guide (Continued)

Rear Front

Smooth

Power Supply Output Cord

A

Mounting

Use the included hook and loop tape to attach the DPH 101 to the application surface.

Cabling

AB

POWER

12V

0.2 A MAX

SIG

DP IN

DPH

101

SIG

C

HDMI OUT

DPH 101

Figure 1. DPH 101 Panels

DC power input — Wire the external 12 VDC power supply as shown in gure 2 and connect it to the two-pole captive screw

A

Power connector.

Ridges

SECTION A–A

A

3/16"

(5 mm) Max.

Figure 2. Power Connection

NOTE: See the Attention on the next page for important information.

The DPH 101 can also share power with an Extron switcher or similar device (as shown in gure 3).

PS 1210 C

POWER
12V

0.2 A MAX

SIG

DP IN

DPH 101

DC Power
Shared

DC Power
Output

SW4 HDMI

1

POWER

DPH

12V

101

0.5A MAX

SW4 HDMI

INPUTS OUTPUT REMOTE

234

TALLY OUT

1234+V

1234G

RS-232 AUTOCONTACT

Tx Rx

Figure 3. Sharing Power with an Extron Switcher

DP input — Connect a Dual-Mode DisplayPort input device to the DP input. The DPH 101 equalizes DisplayPort signals up

B

to 15 feet.

NOTE: The DPH 101 can be used with Extron DisplayPort Architectural products, such as the DisplayPort F-F

Architectural Adapter Plate (see figure 5 on page 4). However, it is not recommended to use more than one DP-DP
pigtail in an application.

HDMI output — Connect an HDMI output device to the HDMI output. The DPH 101 reconditions HDMI signals up to 15 feet.

C

NOTE: Extron recommends using HDMI Pro Series cables for 300 Mhz pixel clock (4K/UHD) signals.

2