Extron Electronics CC 100C User Manual

Download

CC 100C • Installation Guide

3.5 mm Micr

Product Category

The Extron

CC 100C is an IP intercom public address and paging device. It is designed for use in Extron classroom

AV systems and facilities utilizing the Extron Global Viewer Campus Communication Suite software.

NOTE: Before installing this device, read the Extron Safety and Regulatory Compliances Guide, available at www.extron.com.

Front Panel

RESET

REMOTE

RS-232/RS-485

MIC

CC 100C

LINE IN OUT SUB

A B

STORAGE

STATUS

USB

Figure 1. CC 100C Front and Rear Panels

Rear Panel

MIC SPKR

INPUT RELAY

0 1 G NO C NC

POWER IN

LAN/PoE

N/A

12-15V

12W MAX

CC 100C Front and Rear Panel Connectors

Front Panel Connections

STORAGE

STATUS

USB

CC 100C

LINE IN OUT SUB

MIC

A B

Front Panel

REMOTE

RESET

RS-232/RS-485

Figure 2. Front Panel Features and Connectors

Front panel connectors and features as shown in gure 2 are listed below.

a Reset Button — Press this reset button once to reset the unit to factory settings, with the exception of the network

conguration settings. To completely reset the unit to factory defaults, including the network conguration settings, press and hold the reset button for 10 seconds and then release.

b Remote Control — Connect to this male 9-pin D-sub port for RS-232 or RS-485 serial control. c Status LEDs — These LEDs indicate power and activity status of the unit. The left LED lights green when power is

present, and the right LED ashes red with unit activity.

d Mic Input — Insert a 3.5 mm connector into this microphone input (TRS) audio jack.

Audio received on this input may be encoded and streamed over the network.

Tip (Mic)

Ring (Power)

Wire the TRS connector as tip = microphone audio, ring = power, sleeve = ground.

e Line In — Connect an unbalanced, line level, mono audio input to this 2-pole connector.

Audio received on this input, when selected, is encoded and streamed across the network.

Sleeve (Gnd)

ophone Input Plug

f Line Out — This 2-pole connector outputs unbalanced, line level, mono audio. Connect this

port to the PoleVault or VoiceLift auxiliary input to amplify the audio for playback through the system speakers.

Sub — This connection port is not used.

g USB Storage — Insert a ash memory USB storage drive with audio le(s) into this port.

Audio les on the drive can be played back or streamed over the network.

CC 100C • Installation Guide (Continued)

RELAY

INPUT

Normally

RELAY

Rear Panel Connections

MIC SPKR

INPUT RELAY

0 1 G NO C NC

LAN/PoE

N/A

Rear Panel

POWER IN 12-15V

12W MAX

Figure 3. Rear Panel Connectors

Rear panel connectors as shown in gure 3 are listed below.

h Mic Input — Microphone audio input is carried on this 3-pole connection. Input is encoded and streamed over the

network. See "Cabling the CC 100C" section on page 3 for wiring details.

i Speaker output (2 watt, mono) — For speaker output, connect a mono speaker to this 2-pole captive screw connector.

See "Cabling the CC 100C" section on page 3 for wiring details.

INPUT RELAY

POWER IN 12-15V

12W MAX

NO C N

Closed

j Conﬁgurable Input: Contact — Connect to this 3-pole captive screw connection

for contact input. When triggered the contact input initiates audio encoding for streaming over the network. Connect port 0 or 1 to ground (G) to trigger the port.

k Conﬁgurable Input: Relay — Connect to this 3-pole captive screw connection for relay

input. The connector has a normally open relay (NO), a common (C), and a normally closed relay (NC).

l N/A — This port is not used.

m LAN/PoE — For networking use, connect the LAN to this RJ-45 connector. This port

supports Power over Ethernet standard up to 48 V. The two associated LEDs indicate connection and data activity. An optional PS PoE power injector (part number 70-828-01) can be used.

n or o Power In — Connect a power supply to either the 2-pole captive screw connector or

to the coaxial connector for 12 V to 15 V power input. Observe the correct polarity.

0 1 G NO C NC

Open

INPUT RELAY

0 1 G NO C NC

1 G

NOTE: It is recommended to use Extron power supplies, such as the 12 V, 1 A PS 1210 C

(part number 70-775-01) or the 15 V, 0.8 A PS 1508 C (part number 70-776-01).

Cabling the CC 100C

Connect the cables to the device as described below.

Step 1 — Connect the LAN Cable

m LAN/PoE — Using a CAT 5e straight through network cable connect to a network. The LEDs light green for link status

and blink amber during activity.

Step 2 — Connect the Mic Input and Speakers

Mic input — Using a 6-pin captive screw connector, wire a

microphone audio input for insertion into the 3 poles labeled as MIC.

Speaker — Using a 6-pin screw block terminal, wire a mono

speaker for insertion into the speaker outputs (+ and -) labeled as SPKR. Wire both connectors as shown in figure 4.

Alternatively, a mono line out connection is also available on the front panel

NOTE: The length of the exposed wires in the stripping

process is critical. The ideal length is 3/16 inches (5 mm). Any longer and the exposed wires may touch, causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws. Do not tin the wires. Tinned wire does not hold its shape and can become loose over time.

Strip wires to 3/16" (5 mm) Max.

Microphone level input

Mic power

Ground

Figure 4. Wiring the Rear Panel MIC Input and

Speaker Output

MIC SPKR

CC 100C Rear Panel

Mono Speaker

Step 3 — Connect the Power

n or o

captive screw port n. Alternatively, insert a power cable into the DC input jack o.

NOTE: Both of these are connected internally so one can be used as a power output for other devices.

Power input — Noting the correct polarity, wire a power cable to a 2-pole connector and insert into this 2-pole

Step 4 — Address the Unit

The CC 100C is now ready to acquire an IP address and announce it over the speaker output. If no DHCP server is available this can take up to 5 minutes.

If audio outputs were not connected in step 2 above, use the ARP command procedure below. Ensure that the Ethernet address (MAC) matches the CC 100C device (see label on the bottom of the device). Now that the IP address is known, the CC 100C is ready to be congured.

Setting a temporary IP address using the ARP command

This procedure will work only in a local network. After this procedure the temporary IP is active only until a restart or reboot. After a restart the procedure has to be repeated.

1. Either use a network cable to link the CC 100C and the PC directly, or connect the CC 100C to the PC via your network switch and power the device. Make sure that you have a valid static IP address configured on your PC (for example

192.168.0.2).

2. Windows: Click on Start, then type Run in the program search eld, and click on Run Porgram. In the Open eld type cmd. Click OK. A command window opens. OSX / Linux: Open a terminal window.

3. If you linked the PC directly to the device in step 1, proceed to step 4. To ensure that you use a free IP address (not already used by another device in the network) use the ping command. To verify availability in this example we assume the PC to have the IP address 192.168.0.2 and want to check if 192.168.0.6 address is available. Type ping 192.168.0.6 and press <Enter>. There should be no reply. This gives the reasonable assertion that the "pinged" IP is available.

CC 100C • Installation Guide (Continued)

4. Find the MAC address of the CC 100C that is printed on a label on the bottom of the device (12 hex digits, separated by

a hyphen every 2 digits). Type into the Windows command window the following: arp -s 192.168.0.6 <unit MAC address>. Alternatively for an OSX or Linux system, type into the terminal: arp -s 192.168.0.6 <unit MAC address> and press the <Enter> key. You must have administrative rights to be able to do so (sudo on OSX / Linux).

5. Use the Telnet command to get the CC 100C to recognize the IP address 192.168.0.6. To do this type into the command window 192.168.0.6 1 and press the <Enter> key.

NOTE: The number one (1) must be added after the address for this command to work correctly.

The device will immediately refuse the connection on port 1, but will be available for browser access as long as the device stays powered.

6. To check if the CC 100C is responding you can use the ping command again. To do so type ping 192.168.0.6 and press <Enter>. If you get a reply, then the IP address 192.168.0.6 can be used to access the CC 100C using a web browser. If you get a "request timed out" notice, repeat step 5 carefully or repeat the entire procedure.

Network Configuration by Web Browser

Normally this device requires no conguration but uses DHCP to congure network settings dynamically.

However, if static (xed) network settings are needed, follow steps 1 to 3 below. If not, continue at step 4.

1. Open a web browser on the connected PC.

2. In the address field enter the IP address that was announced by the CC 100C (see Step 4 - Address the Unit on page 3),

for example: 192.168.0.12, and press <Enter>. The software program opens.

3. Select the Configuration tab at the top of the browser window.

4. Select the Advanced Settings menu from the list at left (see image on page 4).

5. In the Network Settings section, enter the static IP address, the subnet Netmask address, gateway address if applicable.

NOTE: The default 0.0.0.0 sets automatic discovery, BootP, DHCP.

6. Click Apply. The device reboots with the configured IP address.

To complete the application setup, download the rmware documentation from www.extron.com and follow the instructions.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron Europe

+31.33.453.4040

Extron Asia

+65.6383.4400

Extron Japan

+81.3.3511.7655

Extron China

+86.21.3760.1568

Extron Middle East

+971.4.2991800

Extron Korea

+82.2.3444.1571

Extron India

+91.80.3055.3777

68-2509-01

Rev. A 01 14

Extron Electronics CC 100C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual