Cable Cubby 500 and 700 • Installation Guide
Connectivity Bracket
Cable Grommet Plate
Cable Cubby 700
125V~ 12A MAX
TOTAL
Hole Plugs
Connectivity Bracket
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 500
Cable Cubby 700
Zip Ties
Tweeker
AC Power Module
125V~ 12A MAX
TOTAL
#6 Mounting Screws
and Star Washers
#4-40 Module Scr
Cable Grommet Plate
AAP Frame Plate
AC Power Module
125V~ 12A MAX
TOTAL
Cable Grommet Plate
125V~ 12A MAX
TOTAL
Hole Plugs
Connectivity Bracket
Cable Grommet Plate
Cable Cubby 500
Cable Cubby 700
Zip Ties
125V~ 12A MAX
TOTAL
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 700
Tweeker
AC Power Module
125V~ 12A MAX
TOTAL
and Screws
Retractor Pin & Clip
Cable Grommet Plate
AAP Frame Plate
AC Power Module
125V~ 12A MAX
TOTAL
Retractor Pin & Clip
Hole Plugs
Connectivity Bracket
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 500
Cable Cubby 700
Zip Ties
Tweeker
AC Power Module
125V~ 12A MAX
TOTAL
and Star Washers
This guide provides instructions for an experienced installer to install and connect the Extron
Cable Cubby 500 and 700 Cable Access Enclosures.
The Cable Cubby units are furniture-mounted enclosures for cable access,
connections, and AC power. Cables that are not in use can be stored out of the
way while remaining connected to the presentation system.
Planning
Check with local and state regulations before starting
the installation:
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or
other accessibility requirements.
Check all parts and equipment before installation:
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
Kit Contents
Retractor Trim
ews
Cable Cubby 500 Cable Cubby 700
1 2
2 4
1 2
1 2
(3) 3/8", (1) 1/4" (6) 3/8", (2) 1/4"
1 trim, 2 screws 2 trims, 4 screws
#6 Mounting Screws
1 2
4 8
1
Cable Cubby 500 and 700 • Installation Guide (Continued)
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
30
Table Top
x.x"
(x.x cm)
x.x"
(x.x cm)
XL Models
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
XL Models
(23.1 cm)
Cut-Out Template for the Extron
Cable Cubby 500
0.25"
(0.635 cm) R
5.75"
(14.60 cm)
5.75"
(14.60 cm)
2.0"
Trim Ring’s Outer Edge
(Do not cut this line.)
Table Clamp
P/N 68-8599-01 Rev. A
SURFACE
CUT-OUT
AREA
1. Confirm the product to be installed.
2. Remove the surface cut-out area
(gray) from the template.
3. Measure the cutout and template .
4. Mark the position on the
furniture where the Cable Cubby 500
will be installed.
5. Double check dimensions and position,
then cut the opening.
Page Size: 11" x 17"
Print Scale 1:1
Do not Shrink
CutO
C
Cab
Preparing the Table
Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.
Determine the best location for the enclosure
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that the edge on which the lid opens is oriented correctly.
Ensure that there is ample space under the table for cables.
When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table or
furniture (ee dimensions for the retractors below).
NOTES:
• To prevent objects from impeding cable retraction, ensure at least 3 inches of clearance from the exposed cable side of
the enclosure (see the diagrams below).
• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or
entanglement (see Routing and Connecting Cables on page 6).
Table Top
15.9"
9.1"
3.0"
(7.6 cm)
3.0"
(7.6 cm)
XL Models
Choose a method for cutting the hole in the table
ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the furniture.
ATTENTION: L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et
qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
(40.4 cm)
21.9"
(55.6 cm)
ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
(59.7 cm)
23.5"
29.4"
(74.7 cm)
XL Models
30
10.6"
(26.9 cm)
26.7"
(67.8 cm)
Choose one of the following methods for cutting the hole:
Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router
Jigsaw
If using a CNC wood router or other
precise machinery, use the exact
cut-out dimensions for your model
Visit www.extron.com for Cable Cubby routing
template part numbers and instructions.
Cut-Out Template for the Extron
2.0"
Ta
b
le Clamp
Trim Ring
0.25"
Lip Width
+
0.00
0.02
” (
0.00
(0.0
cm)
5 c
m)
User Access
Trim Ring’s
(Do not c
ut th
Cable Cubby 500
Page Size: 11" x 17"
Print Scale 1:1
Do not Shrink
1. Confirm the pr
2. Remove the surface cut-out area
(gray) f
3. M
4. Mark the position on the
furniture where the Cable Cubby 500
easure the cutout and template.
will be installed.
rom the template.
5. Double check
oduct to be installed.
then cut the opening.
Outer Edge
is
line.)
P/N
68-859
dimensions and position,
9-01 Rev. A
Dimensions and cut-out templates are
available online at www.extron.com.
(see the table below).
Cut-out Dimensions
Product
User Access
Width
CC 500 5.75"
(14.6 cm)
CC 700 7.125"
(18.1 cm)
2
Side
Dimension
5.75"
(14.6 cm)
5.75"
(14.6 cm)
Preparing the Cable Cubby
#4-40 Nut
w/ Captive Washer
Insert cables through the bottom of the connectivity bracket.
Connect cables to the AAPs.
Secure the AAP plate on the connectivity brackets,
using two of the provided module screws.
2
3
Step 1 — Assemble the connectivity modules of your choice.
Connectivity modules allow you to populate the Cable Cubby with a combination of AAPs, cable pass-through, or retractors.
AAP Module
Cable
Pass-Through
Module
Secure up to two
1
single-space AAPs
in the AAP plate.
Snap the included hole plugs into
3
any unused holes.
Secure the grommet plate on the
2
connectivity bracket using two
of the provided module screws.
#4-40 Nut
w/ Captive Washer
Secure the AAP plate on the connectivity brackets,
3
using two of the provided module screws.
Insert cables through the bottom of the connectivity bracket.
2
Connect cables to the AAPs.
NOTE: After assembling the module,
proceed to Step 2 — Install the
modules on the next page.
Insert cables through the bottom of the connectivity bracket
1
and into the holes of the grommet plate.
Retractor
Trim
Secure the retractor trim
using the provided
mounting screws (2).
NOTE: After assembling the module,
proceed to Step 2 — Install the
modules on the next page.
NOTE:
• Use a screwdriver to secure the
Retractor trim with the screws.
• After installing the retractor trim,
proceed to Step 2 — Install the
modules on the next page to
install the power module.
• Retractors are installed after the
Cable Cubby is mounted on the
table (see Installing Retractors
on page 5).
3
125V~ 12A MAX TOTAL
Step 2 — Install the modules.
Lower the Cable Cubby into the hole to test the t.
Secure cables with zip ties to the rectangular
holes in the rear of the Cable Cubby.
2
3
Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed
on the left or right side of the enclosure and at various heights.
NOTE:
• Ensure that there is enough room above the modules for the Cable Cubby lid to close completely.
• Use a screwdriver to secure the modules with the screws.
2
Secure the modules using
the provided mounting
screws and star
washers (4) on the
front and back of the
enclosure.
1
125V~ 12A MAX TOTAL
Insert the modules into the Cable Cubby.
WARNING: Risk of Electric Shock. To ensure proper electrical
grounding, use the provided #6-32 mounting screws with the star
washers.
AVERTISSEMENT: Risque de choc électrique. An d’assurer une
mise à la terre correcte, utilisez les xations de mise à la terre #6-32 et
les rondelles en étoile fournies.
Mounting the Cable Cubby in the Table
Step 1 — Mount the Cable Cubby flush with the table.
CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily
nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.
ATTENTION: Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses
et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de
l’endommager ou de vous blesser.
Remove the plastic strips and
1
lm on the surface of the
Cable Cubby.
Ensure that the
2
side clamps are
seated against the
enclosure.
3
If necessary, carefully enlarge the opening.
4
Cable Cubby 500 and 700 • Installation Guide (Continued)
Insert the pin thr
r
the side of the Cable Cubby
and r
Lower the Cable Cubby into the hole to test the t.
If necessary, carefully enlarge the opening.
Remove the plastic strips and
lm on the surface of the
Cable Cubby.
Ensure that the
side clamps are
seated against the
enclosure.
Secure cables with zip ties to the rectangular
holes in the rear of the Cable Cubby.
For cable pass-through applications, allow at least 36 inches (0.9 m)
of cable loop for each cable.
Connect cables to the AV system
and connect the AC power cord.
1
2
3
2
1
3
Step 2 — Under the table, adjust the side clamps on the enclosure.
NOTE: To lower the side
clamp, turn the lever
Lever
Rotate the side clamp
1
outward and ensure that
the lever is down.
Slide the clamp all the way
2 3
up against the bottom of
the table.
Ensure the Cable Cubby
is rmly seated in the table.
Raise the lever to secure
the Cable Cubby.
down, then press and
hold the locking plate
while sliding down the
clamp.
Locking
plate
Installing Retractors
1
2
etractor mounting hole on
etractor assembly.
Insert retractors into
the retractor trim.
ough the
Secure the clip on the pin.
3
4
Secure the locking screw on each retractor.
Do not overtighten.
Horizontal or Angular Mounting
For horizontal or angular mounting, remove
these orientation screws (front and back),
then follow the steps shown at left.
For installation details, see the Cable Retractor
Setup Guide available online at www.extron.com.
5
Routing and Connecting Cables
2
1
For cable pass-through applications, allow at least 36 inches (0.9 m)
of cable loop for each cable.
CAUTION:
Risk of Electric Shock.
This equipment must be grounded.
ATTENTION:
Risque de choc électrique.
Connect cables to the AV system
3
and connect the AC power cord.
Cet équipement doit être xé au sol.
NOTE: Ensure that there is no tension on the power cable.
Secure cables with zip ties to the rectangular
holes in the rear of the Cable Cubby.
Installation Checklist
Planning (page 1)
Check with local and state regulations before starting the installation.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
6
Check all parts and equipment before installation.
Preparing the Table (page 2)
Determine the best location for the enclosure.
Choose a method for cutting the hole in the table.
Preparing the Cable Cubby (page 3)
Choose and assemble a combination of AAPs, cable-pass through, and retractor connectivity to populate
the Cable Cubby.
Secure the connectivity modules and power module in the Cable Cubby.
Mounting the Cable Cubby in the Table (page 4)
Mount the Cable Cubby ush with the table.
Adjust the side clamps.
Installing Retractors (page 5)
Routing and Connecting Cables (page 6)
© 2014 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
68-2491-50
Rev. B
05 14
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
Loading...