Extron Electronics Cable Cubby 1400 User Manual
IMPORTANT:
Connectivity Bracket
Cable Grommet Plate
Cable Cubby 1400
12
5V~ 12A MAX
TOTAL
Cable Grommet Plate
AAP Frame Plate
AC Power Module
12
5V~ 12A MAX
TOTAL
Cable Grommet Plate
12
5V~ 12A MAX
TOTAL
Connectivity Bracket
Cable Grommet Plate
Cable Cubby 1200
Cable Cubby 1400
Zip Ties
12
5V~ 12A MAX
TOTAL
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1400
Tweeker
AC Power Module
12
5V~ 12A MAX
TOTAL
Retractor Bracket
Retractor Pin & Clip
Cable Grommet Plate
AAP Frame Plate
AC Power Module
12
5V~ 12A MAX
TOTAL
Retractor Pin & Clip
Hole Plugs
Connectivity Bracket
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200
Cable Cubby 1400
Zip Ties
Tweeker
AC Power Module
12
5V~ 12A MAX
TOTAL
#6 Mounting Screws
and Star Washers
Hole Plugs
Connectivity Bracket
Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200
Cable Cubby 1400
Zip Ties
Tweeker
AC Power Module
12
5V~ 12A MAX
TOTAL
Go to www.extron.com for the
Cable Cubby 1200 and 1400 • Installation Guide
complete user guide, installation
instructions, and specifications.
This guide provides instructions for an experienced installer to install and connect the Extron
Cable Cubby 1200 and 1400.
The Cable Cubby units are furniture-mounted enclosures for cable access, connections,
and AC power. Cables that are not in use can be stored out of the way while
remaining connected to the presentation system.
Planning
Check with local and state regulations before starting the
installation:
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check all parts and equipment before installation:
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Kit Contents
#4-40 Module Screws
#6 Mounting Screws
and Star Washers
Hole Plugs
Cable Cubby 1200 Cable Cubby 1400
1 2
4 8
1 2
1 2
6 (3/8"), 2 (1/4") 12 (3/8"), 4 (1/4")
1 2
1 2
8 16
1
Cable Cubby 1200 and 1400 • Installation Guide (Continued)
XL Models
Preparing the Table
Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.
Determine the best location for the enclosure
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that the edge on which the lid opens is oriented correctly.
Ensure that there is ample space under the table for cables.
When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table or
furniture. See dimensions for the retractors below.
Table Top
14.9"
9.2"
(23.4 cm)
XL Models
(37.8 cm)
17.8"
(45.2 cm)
(60.2 cm)
(52.8 cm)
23.7"
20.8"
Choose a method for cutting the hole in the table
ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the furniture.
ATTENTION: L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et
qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
23.5"
(59.7 cm)
29.4"
(74.7 cm)
30
10.6"
(26.9 cm)
26.7"
(67.8 cm)
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
Choose one of the following methods for cutting the hole:
Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router
If using a CNC wood router or other
precise machinery, use the exact
cut-out dimensions for your model
(see the table below).
Cut-Out Template for the Extron
Cable Cubby 1200
5. Double check the dimensions and position,
then cut the opening.
Trim Ring
Lip
Outer Edge of Front Bezel
(Do not cut this line.)
P/N 68-2472-01 Rev. A
1. Confirm the product to be installed.
2. Remove the surface cut-out area
(gray) from the template.
3. Measure the cutout and template .
4. Mark the position on the
furniture where the Cable Cubby 1200
will be installed.
Page Size: 11" x 17"
Print Scale 1:1
Do not Shrink
Cut-out Dimensions
Product
User Access
Width
CC 1200 10.00"
(254.0 mm)
CC 1400 10.00"
(254.0 mm)
Visit www.extron.com for Cable Cubby routing
template part numbers and instructions.
2
Cut-Out Radius:
0.25" (0.6 cm)
User Access
Dimensions and cut-out templates are
available online at www.extron.com.
Side
Dimension
4.00"
(101.6 mm)
6.75"
(171.5 mm)
Loading...