Extron Electronics BB 710M User Manual
Product Category
BB 710M • Installation Guide
Refer to www.extron.com for the
Refer to www.extron.com for the
complete TLP 710 series user manual and
complete TLP 710 series user manual and
installation instructions before connecting
installation instructions before connecting
the product to the power source.
the product to the power source.
Overview
The Extron BB 710M back box is used to mount an Extron TLP 710MV TouchLink™ panel in a wall. This Installation Guide
provides instructions for an experienced installer to retrofit the box in existing drywall or mount the back box in a new
installation. For complete instructions about installing and calibrating the TouchLink panel, see the TLP 710MV and
TLP 710TV User Guide, which are available on the Extron web site (www.extron.com).
Retrot an Existing Installation (with the Drywall in Place)
1. Separate and remove the endplates (top and bottom) from the U-plate (sides and
back).
2. Use the back face of the U-plate to mark the position where the hole will be cut. Use a
level to ensure the U-plate is level.
NOTE: The hole is 7.7 inches (19.5 cm) wide x 6 inches (15.1 cm) high.
3. Using a drywall saw, carefully cut a hole where the touchpanel will be installed. Cut on
the lines that you marked in step 2.
4. Run the cable conduit through the wall. The conduit can be attached to any of the
available knock-out holes in the top, bottom, or either side. Leave some slack to
connect the conduit to the back box and the cables to the touchpanel.
5. Run cables to the installation site.
6. Clear the cables and conduits from the space behind the hole.
7. If required, secure a conduit to the U-plate and insert the U-plate
into the hole (see figure 1).
BB 710M
U-plate
Figure 1.
9
7
Tabs (4)
NOTE: The U-plate tabs sit on the outer face of the drywall.
8. Pull back the cables that were cleared out of the way in step 5.
9. If required, secure one or more conduits to the knock-out holes in
the endplate (see figure 2). Break off the lip on the leading edge
of the endplate (see figure 3) to make it easier to maneuver the
endplate with a conduit attached.
10. Slide the endplates into the gap between the back of the U-plate
and the top flanges on the side of the U-plate (see the inset in
figure 2). The endplate must pass the drywall so that the trailing
edge can be pushed in behind it.
11. Secure the endplate to the U-plate, using the four provided
screws. Insert the provided screw from inside the BB 710M,
through the slot in the endplate and into the threaded hole in
the top of the U-plate (see figure 3).
The endplates (behind) and the tabs of the U-plate (in front)
clamp the drywall, holding the BB 710M securely in place.
12. Finish installing the
TouchLink panel
as shown in figure
4 and described
Lip Snaps
Off
in “Mounting the
Touchpanel” on the
next page.
Slot
Threaded
Hole
Figure 3.
10
Figure 2.
Tabs are against
outside surface
of drywall.
Tighten screws to
rotate locking arms.
Bezel snaps to unit
(4 places on each side).
Figure 4.
1
BB 710M • Installation Guide (Cont’d)
New Construction Installation
1. Secure the endplates to the U-plate, using the four provided
screws.
2. Before the drywall has been secured to the studs, place the wall
box in a suitable place so that the tabs on the sides of the box are
flat against a vertical stud.
3. Secure the wall box to the stud (metal or wooden) using two nails
or screws.
4. Run the cable conduits to the box and connect them to one of
the available knock-out holes. Leave enough cable to provide
slack for installing the TouchLink panel.
5. Measure the position of the back box, and mark and cut a hole in
the drywall where the box is placed.
NOTE: The hole is 7.7 inches (19.5 cm) wide x 6 inches
(15.1 cm) high.
Figure 5.
6. Secure the drywall to the studs.
NOTE: The tabs of the wall box sit on the stud against the inner face of the drywall.
7. If required, paint the drywall. Insert the cardboard cover (provided) into the back box to avoid getting paint on it.
Tabs are in contact
with the wall stud.
Extron BB 710M
Wall Box
for Wall-mounting
Extron TLP 710MV
3
Mounting Screws (2)
Mounting the Touchpanel
For complete instructions about installing and calibrating the
TouchLink panel, see the TLP 710MV and TLP 710TV User Guide,
available on the Extron website
(www.extron.com).
1. Connect the cables to the back of the TouchLink panel (see the
user guide). Feed excess cable back into the conduit.
2. Test the connections and configure the TouchLink panel (see
the user guide).
3. Fold the locking arms into their recesses on the side of the
touchpanel and slide the unit into the back box.
4. Tighten the screws on the front of the unit so that the locking
arms rotate into place behind the top and bottom plates of
the back box and hold the unit in place (see figures 4 or 6).
5. Snap the faceplate into position (see figures 4 or 6).
Tabs are against
outside surface
of wall stud.
Tighten screws to
rotate locking arms.
Bezel snaps to unit
(4 places on each side).
Figure 6.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
2
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
(Inside Asia Only)
+65.6383.4400
+65.6383.4664 FAX
© 2012 Extron Electronics All rights reserved. www.extron.com
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
68-2150-01 Rev. B
07 12
Loading...