Extron Electronics AVTrac Trim Ring-Rough-in Adapter User Manual

Extron® AVTrac® Rough-In Adapter • User Guide

This adapter is designed for installation in new stud wall constructions, before installing
the gypsum board walls (drywall). For complete information about installing AVTrac, see
the AVTrac User Guide, which is available online at www.extron.com.

1. Determine where AVTrac will meet

the wall. Cut out a section of the
wall base stud that is 4 inches
(10.1 cm) wide and align the front
edge of the adapter base with the
front edge of the wall base stud.

2. Mark the position of the holes in the

adapter base, drill at least two holes
into the concrete 5/32 inches (0.4 cm)
diameter and 1 1/2 inches (3.8 cm)
deep, and secure the adapter to the
floor, using the provided masonry
screws.

3. Cut a notch 1.5 inches (3.8 cm) high x

4 inches (10.1 cm) wide in the bottom
edge of the drywall and place the
drywall over the rough‑in adapter with
the top edge of the notch resting on
top of the front support of the adapter.
Secure the drywall to the wall frame.

4. Install the AVTrac system (see the AVTrac

User Guide, which is available online at

www.extron.com).

Rough-In Adapter

Front edge of the
adapter base is level
with wall base stud.

Dry Wall

4.0"

(2) Masonry
Screws

Wall Base Stud

1.5"

Rough-In Adapter
Front Support

Extron® AVTrac® Wall Trim Plate • User Guide

The wall trim plate is a finishing plate that compensates for any overcuts to the existing
gypsum wall during AVTrac installation. For complete information about installing AVTrac,
see the AVTrac User Guide, which is available online at www.extron.com.

Install the trim ring in place of, or behind, existing wall base trimmings as follows:

1. Install the AVTrac system, as described in the AVTrac User Guide.

2. Before snapping the cover track in place and

covering the track with a carpet or rubber
strip, place the trim plate against the wall so
that it is seated on the AVTrac, covering the
overcut hole in the wall.

3. Mark the position of the two holes in the

trim ring on the wall and, using the screws
provided, secure the trim plate to the wall.

4. Snap the cover track in place and cover the

track and ramps with carpet, as described in
the AVTrac User Guide. If required, trim the
wall baseboard to fit snugly around the track
and attach it to the wall, over the trim plate.

Wall Tr im Plate

Extron USA - West
Headquarters

+800.633.9876

Inside USA and
Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA and
Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

© 2010 Extron Electronics All rights reserved. www.extron.com

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

68‑1603‑01
Rev.

B

12 10