Extron Electronics AVTrac Raceway Transition User Manual
Extron® AVTrac® Raceway Transition • User Guide
AVTr ac
The AVTrac Raceway Transition provides a clean and efficient transition from the
floor‑mounted AVTrac to a wall‑mounted raceway (not provided).
For complete information about installing the AVTrac system, see the AVTrac User Guide,
which is available on the Extron website (www.extron.com).
The two available versions are:
z Compatible with the Wiremold 4000 series (shown in the illustrations)
or
z Compatible with most Euro Channel trunk systems. The Euro Channel kit does not have
the rabbit ears.
NOTE: The Euro Channel version fits wall‑mounted raceways with dimensions
90 ‑ 120 mm (3.5 ‑ 4.7 inches) wide x 50 ‑ 65 mm (2.0 ‑ 2.6 inches) deep.
Install either model as follows:
1. Install the AVTrac so that it runs up to and meets
the foot of the wall. Do not fix the cover track to
the base track or cover the ramps with carpet at
this time.
2. Remove the two screws holding the front plate in
position and lift it away from the transition unit
(see the figure at right).
3. Place the transition unit on top of the base track
of the AVTrac and against the wall. Mark the
positions of at least two mounting holes in the
base.
Screws (2)
Front Plate
Raceway
Transition
Mounting
Holes
NOTE: If only two screws are used to secure the raceway transition, they must be in
diagonally opposite corners of the base.
4. Drill holes, 5/32 inches (0.4
cm) diameter and 1 1/2 inches
(3.8 cm) deep, through the
Wall-mounted
Raceway
AVTrac and into the concrete
floor.
5. Using the masonry screws
provided, secure the raceway
transition unit to the floor.
6. Install the wall‑mounted
(2) Masonry
Screws
raceway following the
instructions provided by the
manufacturer.
The Wiremold version of the
kit has rabbit ears on the sides,
which fit inside the raceway.
There are no rabbit ears on
the Euro Channel version and
the wall‑mounted raceway is
secured to the wall so that it
sits on top of the transition
unit.
AVTr ac Raceway (base)
Rabbit Ear
(Wiremold kit only)
Extron® AVTrac® Raceway Transition • User Guide (cont’d)
7. Run cables to the AVTrac connectivity box through the raceway transition and the
wall‑mounted raceway.
8. Reattach the front plate of the raceway transition, using the screws retained from
step 2. The front plate of the Wiremold version has a top edge that sits in front of the
wall‑mounted raceway.
9. Fix the AVTrac cover track in place (see the AVTrac User Guide).
NOTE: The AVTrac top track runs up to the front edge of the raceway transition; the
bottom track runs all the way to the wall, under the raceway transition. When
measuring and cutting the top track, remember to account for the depth of the
raceway transition (2.5 inches or 6.4 cm. for the Wiremold version; 3.5 inches or
8.9 cm. for the Euro Channel version).
10. Finish off installing the AVTrac as described in the AVTrac User Guide.
11. Finish off installing the wall‑mounted raceway following the instructions provided by
the manufacturer.
Extron USA - West
Headquarters
+800.633.9876
Inside USA and
Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA and
Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
© 2010 Extron Electronics All rights reserved. www.extron.com
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68‑1604‑01
Rev.
B
12 10
Loading...