Extron electronics 4xi series User Manual

Configuration and ConnectionsToshiba TLP Installation

SYSTEM 4xi

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: TOSHIBA (LCD)

Included Communications Adapter(s):

Quantity Part Number Description

1 26-474-01 ADP, UNV, “F”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: TOSHIBA TLP 710U/711U

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM

AS 1 2 3 4 CABLE ADAPTER

✔ Toshiba 710U/711U off on of f on 0 0 3 E 0 J15 26-474-01

Extron • System 4xi Switcher Series • User’s Manual • P/N 68-427-02 Rev. B

Toshiba TLP Installation Configuration and Connections

y

)

Connecting System 4xi to Toshiba TLP 710U/711U Projector

If the System 4xi is already configured for a Toshiba 710U/711U projector, go to
step 4. If it is not set up correctly, it will be necessary to change switch settings

on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct
configuration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Toshiba projector. Apply power to the System 4xi and do
the following:

a. Press to display the MENU SELECT on the LCD screen.

or to step to Menu 8.

to select this menu.

System 4xi User’s Manual

to remove the

[System 4xi model and software

version displayed here]

(See note.)

(See note.)

(See note.)

(Note: Information depends on

stem 4xi

S

(See note.)

setup.

b. Press
c. Press
d. Press or to display the configuration. The example to the left is general,

yours will show the System 4xi model name, the software version and the
following information:
PRJ = TOSHIBA

}

PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)

2. Go to the procedure on page 2-3 of the

System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.

Config Projector SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Comm

as Adapter

✔ Toshiba 710U/711U off-on-off-on 0 0 3 E 0 J15 26-474-01

SW3

SW5

3. Double-check your work and be sure the System 4xi cover is on securely.

4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.

__________ Changes in some switch configurations are not detected until the power is

removed at the AC cord, and then restored.

Refer to the following connection diagram and continue.

5. The Toshiba Comm Adapter (26-474-01) has a 9-pin male connector that
accommodates the Comm Extension cable. The other end of the Comm Adapter
plugs into the projector’s 15-pin “RS-232C” port.

Extron • System 4xi Switcher Series • User’s Manual • P/N 68-427-02 Rev. B

SW2

SW4

J15

SW1

4

3

2

1

ON

Page 1