Extron Electronics 3G-AE-100 Setup Guide
IMPORTANT:
Smooth
Power Supply Output Cord
A
Do not tin the wires!
Balanced Audio Output
Unbalanced Audio Output
No Ground Here
Go to www.extron.com for the complete
3G-AE 100 • Setup Guide
user guide, installation instructions, and
specifications before connecting the
product to the power source.
The Extron 3G-AE 100 extracts embedded digital audio from a 3G-SDI, HD-SDI, or SDI
signal and converts it to analog stereo audio at the output ports. This guide provides basic
instructions for an experienced installer to set up and operate the 3G-AE 100.
WARNING: Installation and service must be performed by authorized personnel only.
Installation
ATTENTION: Turn the input and output devices off and unplug their power cords.
Verify that the 3G-AE 100 is disconnected from the power source before proceeding.
3G-AE
100
POWER
12V
0.8A MAX
3G/HD
SD-SDI
LOOP
THROUGH
CH 1 CH 2 CH 3 CH 4
CH 5 CH 6 CH 7 CH 8
GROUP
SELECT
SPARE
1/2
ON
1
2
3/4
INPUT ANALOG OUTPUTS
1
2 3
4
Figure 1. 3G-AE 100 Rear Panel
Wire the power supply as shown below and connect it to the power connector.
a
SECTION A–A
Connect an input device to the 3G-SDI input connector.
b
If necessary, connect an output device to the Loop Through connector. This connector may
c
Ridges
A
3/16”
(5 mm) Max.
also be used for cascading to another 3G-AE 100.
NOTE: It is not required to connect a device to the Loop Through connector in order to
extract audio from the input device.
Connect up to four audio output devices to the Analog Outputs, using a cable with a
d
balanced or unbalanced 3.5 mm, 5-pole captive screw connector. Wire as shown below.
Sleeves
Ring
Ring
Tip
Tip
LR
Tip
Sleeves
Tip
No Ground Here
LR
Front Panel Features
G/
DI
EE0
0
O
P
THRO
GH
G
T
DI
0
0
O
P
THROUGH
A
X
R
R
U
2
-
O
G/
DI
EE0
0
O
P
THRO
GH
A
X
G
T
DI
0
0
O
P
THROUGH
A
X
R
R
CH 5 CH 6 CH 7 CH 8
CH 1 CH 2 CH 3 CH 4
ANALOG OUTPUTS
GROUP
SELECT
SPARE
1
1/2
3/4
2
ON
Group 1 is output on
the top ports.
Group 2 is output on
the bottom ports.
1 2
RATE
270 Mbps 1.485 Gbps 2.97 Gbps
NOT
RECOGNIZED
3G-AE 100
MULTI-RATE SDI AUDIO EXTRACTOR
Figure 2. 3G-AE 100 Front Panel
Power LED — Lights when receiving power.
a
Rate LEDs — Indicate the data rate of the incoming signal.
b
Operation
Audio Group Selection
The 3G-AE 100 supports up to sixteen channels of embedded digital audio. SDI audio is
divided into four groups; each group has four channels. When an audio group is enabled, its
channels are extracted and routed to the 3G-AE 100 analog output ports.
The Group Select DIP switch can enable two groups (eight channels) at the same time:
• To enable groups 1 and 2, set the switch to 1/2.
Group 1 is output on
the top ports.
Group 2 is output on
the bottom ports.
CH 1 CH 2 CH 3 CH 4
CH 5 CH 6 CH 7 CH 8
ANALOG OUTPUTS
• To enable groups 3 and 4, set the switch to 3/4.
Group 3 is output on
the top ports.
Group 4 is output on
the bottom ports.
NOTE: All sixteen channels can be extracted at the same time by cascading two
CH 1 CH 2 CH 3 CH 4
CH 5 CH 6 CH 7 CH 8
ANALOG OUTPUTS
3G-AE 100 devices via the Loop Through input (see c on the previous page).
GROUP
SELECT
SPARE
1/2
ON
1
2
3/4
GROUP
SELECT
SPARE
1/2
ON
1
2
3/4
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2477-50
Rev. A
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
08 13
Loading...