Extron electronic XTRA User Manual

Setup Guide — XTRA Series Audio Power Amplifiers
Do not tin the wires!
Balanced Stereo Input
Tip
Ring
Tip
Ring
L R
Sleeves
Unbalanced Stereo Input
Tip
Sleeve
Sleeve
Tip
L R
Balanced Mono Input
(high impedance)
Tip
Ring
L R
Sleeve
Unbalanced Mono Input
Tip
Sleeve
L R
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714 .491.1500 +1.714 .491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794 +1.919.863.1797 FA X
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040 +31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400 +65.6383.4664 FAX
Extron Japan
+81.3.3511.7655 +81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568 +86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800 +971.4.2991880 FAX
12
OUTPUT
XPA 1002
XPA 2001-70V
OUTPUT
70V
XPA 2001-100V
OUTPUT
100V
LEVEL
0
XPA 2001
LEVEL
1 2
0 0
XPA 1002
123 45
STANDBY
VOL/MUTE
10V 50 mA
123
STANDBY
VOL/MUTE
10V 50 mA
W
Installation and service must be performed by authorized personnel only. These
products must be used with UL approved, grounded, electrical boxes.
This guide provides startup instructions for an experienced installer to set up and operate the XPA 1002 or XPA 2001 audio power amplifier. All references are to the XTRA Series user’s manual.
Step 1
N
Adjust the audio level to - = (full attentuation) prior to the amplifier being powered back up in Step 5. See "Rear Panel
Features and Operation" in chapter 3 of the user’s manual.
Turn off all other equipment and disconnect the power cords. Verify that the amplifier is disconnected from the power source before proceeding.
Step 2
For diagrams of typical application examples, see "Application Examples" in chapter 2. For further mounting instructions, see "Mounting the XPA 1002 and XPA 2001" in chapter 2 of the user’s manual.
Step 3
Wire input to the amplifier's input 3.5 mm connectors, as shown in the following illustration. See "Rear Panel Features and Operation" in chapter 3 of the user’s manual.
N
The XPA 1002’s output power can be effectively doubled by using only one input channel and bridging the output. The
XPA 1002 outputs 200 watts @ 8 ohms or 120 watts @ 16 ohms in bridged mode. See “Bridged mode output” in chapter 3 of the user’s manual for wiring instructions when bridging the XPA 1002
N
For mono input on the XPA 2001, only the left channel needs to be wired; no jumpering to the right channel is needed.
Step 4
Wire speakers to the amplifier’s output connector using the included 4-pole (XPA 1002) or 2-pole (XPA 2001-70V and XPA 2001-100V) screw lock plug as shown to the right. See “Rear Panel Features and Operation” in chapter 3 of the user’s manual.
Step 5
Reconnect all power cords and switch on all other equipment before powering up the power amplifier. The amplifier must be powered up last. The amplifier’s front panel power LED should light green.
Step 6
Adjust the audio level using the rear panel adjustment screws as shown to the right. See “Rear Panel Features and Operation” in chapter 3.
Step 7
The limiter/protect and signal LEDs located on the front and rear panels should be checked if problems are encountered. See “Front Panel Features and Operation” in chapter 3.
Step 8
The 3.5 mm 5-pin captive screw remote control connector (shown to the right) is used to control volume and standby mode through contact closure. Standby mode turns off all output, although the XPA is still receiving power. See “Front Panel Features and Operation” in chapter 3.
68-1351-50
Rev. A
02 09
Loading...