Extron electronic VTG 400D User Manual

Specifications — VTG 400D
Video signal characteristics
Dot clock ����������������������������������������� 200 MHz (max�) Pixel clock accuracy ���������������������� 100 ppm Horizontal frequency range (factory defaults)
Vertical frequency range (factory defaults)
30 Hz to 120 Hz
Rise/fall time
NTSC, PAL ������������������������� 140 ns All other signal rates ��������� <4 ns
Video output
Number/signal type ��������������������� 1 RGBHV, RGBS, RGsB, RsGsBs, component video, HDSDI (SMPTE 292M),
SDI digital component video (SMPTE 259M-C), S-video, composite video (NTSC/PAL)
Connectors ������������������������������������� 1 x 5 female BNC (RGB)
1 female 15-pin HD (RGB) 1 x 3 female BNC (component video) 1 female 4-pin mini DIN (S-video) 1 female BNC (composite video) 1 female BNC (SDI/HDSDI)
Nominal level �������������������������������� 1 Vp-p for Y of component video and S-video, and for composite video,
RsGsBs 0�7 Vp-p for RGB and for R-Y and B-Y of component video 0�286 Vp-p (burst) for C of NTSC S-video, 0�300 Vp-p (burst) for C of PAL
S-video Minimum/maximum levels �������� 0�0 V to 1�0 Vp-p Impedance �������������������������������������� 75 ohms Resolutions ������������������������������������� Computer (VGA–QXGA), video (NTSC, PAL), HDTV, 16:9 high resolutions,
and custom resolutions (user-defined) Return loss �������������������������������������� -30 dB @ 5 MHz DC offset ����������������������������������������� 0 ±5 mV for RGB and component video,
0 ±5 mV for NTSC S-video and composite video
14 mV ±5 mV for PAL S-video and composite video
Sync
Output type ������������������������������������ RGBHV, RGBS, RGsB, RsGsBs (for RGB signals)
Tri-level on Y, R-Y, B-Y channels (component video 720p, 1080i, 1080p)
Bi-level on Y channel (for all other component video rates) Standards ���������������������������������������� NTSC, PAL, SMPTE 170M, SMPTE 274M, SMPTE 293M, SMPTE 295M,
SMPTE 296M Output level ����������������������������������� 0�3 Vp-p for RGsB, RsGsBs, component video (bi-level sync)
0�6 Vp-p for RsGsBs, component video (tri-level sync)
TTL: 5�0 Vp-p, unterminated for RGBHV, RGBS Output impedance ������������������������ 75 ohms Max� rise/fall time ������������������������ 5 ns (TTL sync) Polarity�������������������������������������������� Positive or negative (scan rate/signal dependent) Scope trigger connectors �������������� 1 BNC female (scope trigger)
Audio
THD + Noise ���������������������������������� <0�008% typical @ +6 dBu (1�55 V), 1 kHz
0�18% @ -38 dBu (9�75 mV), 20 Hz to 20 kHz Flatness ������������������������������������������� ±0�05 dB @ 20 Hz to 20 kHz Accuracy ����������������������������������������� ±0�4 dB
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Extron VTG 400D Video Test Generator • Specications
1
Specifications — VTG 400D, cont’d
Audio output
Number/signal type ��������������������� 1 mono, balanced; 2 mono, unbalanced Connectors ������������������������������������� (1) 3�5 mm mini stereo jack (unbalanced mono left and right, tip-ring-sleeve)
1 female RCA jack (unbalanced, tip-ring) 1 male 3-pin XLR (balanced) (pin 1 = GND, pin 2 = +, pin 3 = -)
N
Impedance �������������������������������������� 50 ohms unbalanced, 100 ohms balanced Waveforms ������������������������������������� Pink noise, white noise, sine wave (fixed/swept burst), square wave,
polarity test
Level ranges ����������������������������������� Pink noise: -72 dBu to -4 dBu (-74 dBV to -6 dBV) (0�20 mV to 500 mVrms)
Polarity test: -72 dBu to -14 dBu (-74 dBV to -16 dBV) (0�20 mV to 158 mVrms) All other signal types: -72 dBu to +6 dBu (-74 dBV to +4 dBV) (0�20 mVrms to
1�58 Vrms) Maximum level (Hi-Z) ����������������� >+6 dBu, balanced or unbalanced at 1% THD+N Maximum level (600 ohm) ����������� >+4�66 dBu, balanced or unbalanced at 1% THD+N Crest factor (pink noise) ��������������� 3�25 (10�24 dB) Crest factor (white noise) ������������� 1�98 (5�95 dB) Rise time (square wave) ��������������� 1�5 ms at 20 Hz to 7 µs at 5 kHz Rise time (polarity test) ���������������� 5 µs Frequency accuracy (sine wave) � 50 ppm
Control/remote— test generator
Serial control port �������������������������� RS-232, 9-pin female D connector Baud rate and protocol ����������������� 9600 baud, 8 data bits, 1 stop bit, no parity Serial control pin configurations � 2 = TX, 3 = RX, 5 = GND Program control ����������������������������� Extron’s control/configuration program for Windows
Extron’s Simple Instruction Set (SIS™)
General
Power ���������������������������������������������� 100 VAC to 240 VAC, 50/60 Hz, 15 watts, internal Temperature/humidity ���������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing Cooling ������������������������������������������� Convection, no vents Mounting ���������������������������������������� No Enclosure type ������������������������������� Metal Enclosure dimensions ������������������� 6�75" H x 9�0" W x 1�75" D
(17�1 cm H x 22�9 cm W x 4�4 cm D)
(7�5" [19�1 cm] H including connectors�) Product weight ������������������������������ 3�3 lbs (1�5 kg) Shipping weight ���������������������������� 7 lbs (4 kg) Vibration ����������������������������������������� ISTA 1A in carton (International Safe Transit Association) Regulatory compliance
Safety ����������������������������������� CE, CUL, UL
EMI/EMC �������������������������� CE, C-tick, FCC Class A, ICES, VCCI MTBF ����������������������������������������������� 30,000 hours Warranty ����������������������������������������� 3 years parts and labor
N N
All nominal levels are at ±5%. Specifications are subject to change without notice.
The XLR output is immune to phantom power.
®
7.6-121108-D10
2
Extron VTG 400D Video Test Generator • Specications
Loading...