Extron electronic SW MTP T 15HD A User Manual
Setup Guide — SW MTP T 15HD A
Unbalanced Stereo Output Balanced Stereo Output
L R
Do not tin the wires!
Ring
Sleeve(s)
Tip
Tip
Ring
Sleeve(s)
Tip
Tip
NO GROUND HERE.
NO GROUND HERE.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4 050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
A A
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
PREPEAK
ON
OFF
REMOTE
INPUT 2
INPUT 1
AUDIO
RGB/AUDIO
PREPEAK
ON
OFF
OUTPUT
L R
POWER
12V
0.2A
M
A
X
INPUT 4
INPUT 3
INPUT 6
INPUT 5
INPUT
OUTPUT
POWER
12V
.5A MAX
MTP R 15 HD A
ON
1 2 3 4
5 6
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
SPARE
1
M
O
N
O
A
U
D
IO
2
Extron
SW6 MTP T 15HD A
Switcher
Extron
MTP R 15HD A
Receiver
Laptop
Laptop
Monitor
Sound System
System Control
INPUT 2
INPUT 1
INPUT 4
INPUT 3
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
Pin
RS-232
Contact
Closure
Function
1
— In #1 Input #1
Input #2
Input #3
Input #4
Input #5
Input #6
2
TX —Transmit data
3
RX — Receive data
4
— In #2
5
Gnd Gnd Ground
6
— In #3
7
— In #4
8
— In #5
9
— In #6
Setup Guide — SW MTP T 15 HD A (cont’d)
This sheet provides quick start instructions for an experienced installer
to set up and operate any of the SW MTP T 15HD A Series
switchers.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power
sources and mount the MTP switcher as required.
Step 2 — Video and audio inputs
• Connect up to two, four, or six computer (VGA) video
sources to the Input connectors.
• Plug up to two, four, or six 3.5 mm stereo audio plug into
the audio jack.
Step 3 — TP output to the receiver
Terminate a TP cable as shown at right. Connect it
between the RGB/Audio Output connector and a
compatible MTP receiver.
N The cable should all be terminated using the
same standard on both ends of the cables.
Step 4 — Connect a local audio device
Connect an audio device to the Audio connector.
Wire the connector as shown at right.
Operation
Select an input — Press and release the desired input button.
Toggle auto switch mode on and off —
1. Press and hold the Mode (Input 1) button.
2. Press and release the Auto (Input 3) or Normal (Input 2) button.
3. Release the Mode button.
Typical SW6 MTP T 15HD A application
C Connect the sleeves to ground (Gnd). Connecting the sleeve to a negative (-)
Step 5 — Power
Wire the 2-pole captive screw connector for the included
external 12 VDC power supply as shown at right. Plug it into
the switcher.
Step 6 — Remote connector
N Use only one remote control type, RS-232 serial or
Connect an RS-232 OR contact closure controller. Wire the
connector as shown in the table at right. For contact closure
control, momentarily tie an input pin to ground to select
that input.
Step 7 — Pre-Peak
contact closure.
View the image and set the Pre-Peaking switch for the
best image quality to correct for long cable runs of the
entire sytem (including all daisy-chained receivers).
terminal will damage the audio output circuits.
68-909-50
Rev. A 02 09
Loading...