Extron electronic RM 700M User Manual

RM 700M Mounting Kit Installation Guide

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714 .491.1500 +1.714 .491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FA X

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400 +65.6383.4664 FAX

Extron Japan

+81.3.3511.7655 +81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800 +971.4.2991880 FAX

Tighten screws to rotate locking arms.

Secure RM 700M to rack.

Screws (6) Provided by Manufacturer

Faceplate snaps to unit. (4 plcs ea side)

RM 700M

Power input

Video inputs (2)

LAN input

TLP 700MV Rear Panel

Overview

The Extron® RM 700M allows the TLP 700MV TouchLink™ panel to be mounted in a standard rack. The RM 700M uses 5 U of vertical space in a standard 19 inch equipment rack.

This guide provides basic instructions for an experienced installer to mount and connect the TLP 700MV.

Using the RM 700M mounting kit

To mount the TLP 700MV in any standard 19" equipment rack, follow these instructions:

Disconnect all cables from the TLP 700MV.

2. Run cables for video, network and power to the rack.

3. Secure the RM 700M to the rack, using

the screws provided by the rack's manufacturer.

Remove the faceplate from the

TLP 700MV and ensure that all the locking arms are laying ﬂush with the unit.

Push the

TLP 700MV through the hole in the mounting kit and tighten the six screws for the locking arm. As the screws tighten, the locking arms rotate and clamp against the back of the mounting kit, holding the TLP 700MV in place.

6. Connect the cables to the rear panel connectors.

Connect the LAN port to the network with a

straight-through cable.

Connect an S-video or composite video source to

the unit, using these two BNC connectors:

For S-video, connect the Y (luminance) signal • to the VID/Y input and the C (chrominance) signal to the C input.

For composite video, connect the input to the • VID/Y input.

Connect the power input to a 12 VDC, 1.0 A

power supply, using the 2-pole captive screw connector.

7. If you do not plan to calibrate the TLP 700MV immediately (see the TLP 700MV user's manual), replace the faceplate by pressing the catches on the faceplate into the corresponding holes on the sides of the panel.

68-1793-01

Rev. A 08 09

UL Guidelines for Rack Mounting

The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of these products in a rack:

. Elevated operating ambient temperature — If the unit is installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, install the equipment in an environment compatible with the maximum ambient temperature (Tma: +113 °F, +45 °C) speciﬁed by Extron.

. Reduced air ﬂow — Install the equipment in the rack so that the equipment gets adequate air ﬂow for safe

operation.

. Mechanical loading — Mount the equipment in the rack so that uneven mechanical loading does not

create a hazardous condition.

. Circuit overloading — Connect the equipment to the supply circuit and consider the effect that circuit

overloading might have on overcurrent protection and supply wiring. Give appropriate consideration to the equipment nameplate ratings when addressing this concern.

. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment. Pay

particular attention to supply connections other than direct connections to the branch circuit (such as the use of power strips).