Extron electronic RGB 464XI User Manual
RGB 460xi Series • Setup Guide
Closed / On
This guide provides basic instructions for an experienced technician
to install the Extron RGB 46x series of architectural adapter plates
(AAP) plates.
For additional details see the RGB 460xi Series User Guide at
www.extron.com.
NO MONITOR
MONITOR
AUDIO
MONITOR
INPUT
H. SHIFT
MIN/MAX
Product Category
VIDEO S-VIDEO
AUDIO
L/MONOR
Disconnect Power
RGB 464xi
Turn off all equipment. Disconnect the computer, the interface, and output devices from the power source.
Attach AAPs
Attach any optional AAPs to the interface (RGB 468xi, RGB 468 Mxi, or RGB 468xi AKM UK only), before connecting cables
(see the RGB 460xi Series User Guide for more details).
Set DIP Switches
A bank of DIP switches, (see item
up sets it On as shown by switch 7 at right. Moving it down sets it Off.
NOTE: The default for all DIP switches, except switch 7, is off (down). Switches 7 and 8 work
together for sync routing. They cannot both be set to on, nor can both be set to off.
Switch
Number
Function Setting Description
1 Sync on green
2 Composite sync
3
Digital Display Sync Processing
(DDSP™)
4 Serration pulse
5 Vertical sync pulse width
6 Negative sync
on the rear panel diagram on the next page), controls various options. Moving a switch
a
2
1
3
Off
Outputs separate horizontal and vertical sync on the H and V
connectors for RGBHV.
On Outputs sync on green (SOG).
Off Outputs RGBHV or RGsB video.
On Outputs combined horizontal and vertical sync for RGBS.
Off Interface performs sync process operations with Advanced
Digital Sync Processing (ADSP™).
On Interface uses DDSP.
Off Serration pulses are off.
On Serration pulses are on.
Off Wide
On Narrow
Off Output sync same as input.
On Output sync for to negative polarity.
4
7
5
6
Open / Off
8
Off Must be set to Off if switch #8 is On.
7
On
Sync routing to 15-pin HD local monitor for all Macintosh
(other than 13 inch) and VGA monitors (default).
®
Composite sync routing
Off Must be set to Off if switch #7 is On.
8
On
Sync routing to 15-pin HD local monitor for Macintosh 13 inch
monitors.
1
9-24 VDC
Cable the Rear Panel
DIP Switches — Used to set options, see previous page.
a
RGB video output connectors — Attach video cables from the
b
interface to the display device using these female BNC connectors.
See the video output connections diagram (below right) for the
wiring diagrams.
Gain switch — To compensate for longer cable runs, slide this
c
switch to select the level of video gain that yields the sharpest
picture.
Power connector — Connect a 9 to 24 VDC power supply to this
d
3.5 mm, 2-pole, direct insertion captive screw connector. Wire the
connector as shown below at right. Polarity is not important.
Audio output connector — Insert wires into and tighten the
e
screws on this 3.5 mm, 5-pole, direct insertion captive screw connector for
unbalanced or balanced audio output. Wire the connector as shown in the
audio wiring diagrams below at right.
NOTE: Items f, g, h, and i are features of the RGB 464xi
interface only.
66
7
7
8
8
99 51
Rear Panel Connections and Switches
RGBHV
RGBS
44
R-Red G-Green B-Blue
55
H-Black
22
33
V-Yellow
Composite video pass-through BNC connector — A male BNC connector
f
attaches here.
S-video pass-through 4-pin mini-DIN connector — A male 4-pin mini-DIN
g
connector attaches here.
Balanced active audio output connector — Insert wires into this 3.5 mm,
h
5-pole, direct insertion captive screw connector for balanced active audio
output, then tighten the screws. Wire the connector as shown below at right.
Network pass-through RJ-45 connector — If this connector is not required, a
i
blank cover is supplied to fill the opening.
Apply Power and Test the Interface
Apply power to the interface. The power LED on the front panel lights.
Before mounting into the wall, connect all input sources to the interface. Power
up all AV devices connected to the interface. Check that all are working properly.
If not, check cabling and switch settings, and make adjustments as necessary.
Disconnect Power and Mount the Interface
Disconnect power from all the devices except the interface.
Mount the interface as explained in the appropriate installation guide.
Connect Power
Once the interface is properly mounted, restore power to all connected devices.
The interface is now ready for operation.
S-Black YellowR-Red G-Green B-Blue
RGsB
Black YellowR-Red G-Green B-Blue
Video Output Connections
or
or
Power Connector Wiring
CAUTION: For an unbalanced stereo output, connect
the sleeves to the ground contact.
DO NOT connect the sleeves to the
negative (–) contacts.
NO GROUND HERE
Tip
Sleeve (s)
NO GROUND HERE
Tip
Unbalanced
Stereo Output
Ring
Tip
Sleeve (s)
Ring
Tip
Balanced
Stereo Output
Do not tin the wires!
Audio Wiring
RL
RL
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
2
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-542-50
Rev. B
07 11
Loading...