Extron electronic RGB 116P User Manual

Specifications

OUTPUTS

Input Video Signal:

Input Sync Signal:

Output Signal:

Frequency Compatibility:

RGB Video Bandwidth:

Wall Mount Power Supply:

Below is an example of how an RGB 116p may be connected to a
computer, through an MBC cable.

Specifications

..Analog: .5 to 1.2 volts p-p
..ECL: .8 to 1 volt p-p

..Sync on Green (RGsB)
..Composite Sync (RGBS)
..Separate H&V (RGBHV)

..Video: .5 to 1 volt p-p

..Horizontal: 15-100 kHz (automatic)
..Vertical: 30-170 Hz (automatic)

..150 MHz (2.1 nS Rise Time)

..115 VAC, 60 Hz to 15 VDC/900 mA

User’s Guide

Laptop or
Notebook
Computer

Extron Electronics

1230 South Lewis Street
Anaheim, CA 92805

SM

714-491-1500 FAX [phone]
U.S.A.

LBC Mac 35/VGA HR

MBC IBM

VGA/XGA HR

MBC SUN
Sparc HR

MBC Mac/
Quadra HR

Extron Electronics, Europe

Beeldschermweg 6C
3821 AH Amersfoort
[phone] FAX [phone]

The Netherlands

Large Screen Projector

Or

Data Monitor

Extron Electronics, Asia

41B Kreta Ayer Road
Singapore 089003
[phone] FAX [phone]
Singapore

79-04

68-333-01

Rev. B

RGB 116 Interface

pp

(P/N 60-162-01)

Installation and Operation

Installation and Operation

Description

The RGB 116p has a Video Bandwidth of 150 MHz and is
compatible with any Analog computer system with a horizontal
frequency range of 15-100 kHz (optimum 15-62 kHz). Using
Extron MBC Cables, the RGB 116p is compatible with VGA, Super
VGA, IBM PS/2, MAC, MAC Quadra, XGA, XGA-2, DEC and
many others. Call Extron or refer to Extron’S Handbook of
Computer Interfacing for a complete listing.

Installation (See illustration)

1. Turn off computer and its Monitor.

2. Disconnect the local Monitor cable from the computer and connect
it to the MBC cable.

3. Connect MBC display output cable to “Analog/ECL” on the
RGB 116

4. Connect the MBC’s CPU cable to the
computer’s video output.

5. Apply power to the RGB 116
monitor.

Automatic Sync Output— The RGB 116

automatically strip incoming Sync from the
R, G & B video channels. Sync will output
one of three ways, depending on the output
termination.

• 75 ohms on only R, G, & B channels, output is
sync on Green.

• 75 ohms on only R, G, B, & H/HV channels,
output is composite sync.

• 75 ohms on R, G, B, H/HV & V channels, output
is separate H & V sync.

p

.

OUTPUTS

Rear Panel

ON

(off)

p

, the CPU and

p

will

CPU

MBC

Cable

Power

Monitor

Operation

Power LED: Indicates if the RGB 116p is receiving power.
Horizontal Center Control: The H Center Control [ ] shifts the

displayed image left or right.

Universal Input: Using E

both the computer monitor and large-screen projector/monitor at
the same time.

Termination Switch: 75 ohm video termination for applications with

no local monitor (Sw7, below).

RGB 116

pp

p

with Laptops

pp

When using the RGB 116p with laptops (or computers without
monitors) a termination adapter must be used to simulate a
monitor. If not, the computer/laptop may not boot up or may
default to an undesired lower resolution. Extron has termination
adapters for VGA, MAC, SUN and SGI. 75 ohm video termination
is selectable via DIP switch control.

Switch# Position Function

1 ON Does not allow Sync on Green

OFF Normal-Automatic Sync Output Detection

2 ON Removes serration pulses

OFF Normal-serration pulses passed through

3 ON Video Gain Boost (x1.4)

OFF Video Gain Unity (x1.0)

4 ON Negative Sync at all times

OFF Normal-Sync output polarity tracking

5 ON No Sync Processing (disables center control)

OFF Normal-Sync Processing

6 ON Separate H and V Sync at all times

OFF Normal - Automatic Sync output selection

7 ON 75 ohm Input termination (no local monitor)

OFF High Z Input termination (with local monitor)

Front Panel

XTRON’S MBC input cables allows viewing on

1

Extron • RGB 116p Interface • User’s Guide

Extron • RGB 116p Interface • User’s Guide

2