Extron electronic 400 User Manual 2

Download

Page 1

User’s Manual

Extron Electronics, USA

1230 South Lewis Street, Anaheim, CA 92805

800.633.9876 714.491.1500 FAX 714.491.1517 USA

Extron Electronics, Europe

Beeldschermweg 6C, 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands

Extron Electronics, Asia

135 Joo Seng Rd. #04-01, PM Industrial Bldg. +65.383.4400 FAX +65.383.4664 Singapore 368363

Extron Electronics Information

ExtronWEB™: www.extron.com ExtronFAX™: 714.491.0192 24-hour access—worldwide!

RGB 400 Series

Mountable Interfaces

68-364-01

Printed in the USA

Page 2

Precautions

Safety Instructions • English

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating

instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future

reference.

Follow Warnings • Follow all warnings and instructions marked on the

equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not

recommended by the equipment manufacturer because they may be hazardous.

Consignes de Sécurité • Français

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de

sécurité et d’exploitation avant d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de

pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et

consignes marqués sur le matériel ou présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni

d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,

sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit

des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und

Anleitungen auf dem Gerät oder in der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,

die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Instrucciones de seguridad • Español

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de

operación y seguridad, antes de usar el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad

para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones

marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no

sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.

Warning

Power sources • This equipment should be operated only from the power source

indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all

power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to

be stepped on or pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no user-

serviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are

provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced.

Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation

indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,

déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de

manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-

maintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,

ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la

batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene

Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,

sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht

im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem

Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse

aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.

Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo

de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la

acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se

deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal

calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/ mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,

es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición

incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, Europe, Africa, and South America, and the Middle East: Asia: Central America:

Extron Electronics, Europe Extron Electronics, Asia Extron Electronics Beeldschermweg 6C 135 Joo Seng Road, #04-01 1230 South Lewis Street 3821 AH Amersfoort PM Industrial Bldg. Anaheim, CA 92805, USA The Netherlands Singapore 368363

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification to the product.

If it has been determined that the product is defective, please call Extron and ask for an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), or 65.383.4400 (Asia) to receive an RA# (Return Authorization number). This will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Page 3

Table of Contents

Chapter 1 • Introduction .......................................................... 1-1

About this Manual ................................................................ 1-2

About the RGB 400 Series Interfaces .......................... 1-2

Features ...................................................................................... 1-2

RGB 400 Series features ......................................................... 1-2

Additional RGB 404 features ................................................ 1-2

Additional RGB 406 and RGB 408 features .......................... 1-2

Chapter 2 • Installation and Operation ......................... 2-1

Installation Overview .......................................................... 2-2

Installation and Operation Instructions .................... 2-3

Determining installation location ........................................ 2-3

Preparing the installation site, installing the wall box ....... 2-4

Front and rear panel (circuit board) features ...................... 2-6

RGB 404 front and rear features ...........................................2-6

RGB 406 front and rear features ...........................................2-8

RGB 408 front and rear features ........................................ 2-12

Setting DIP switches and jumpers ....................................... 2-12

DIP switches ..................................................................... 2-12

Jumpers ........................................................................... 2-12

Attaching adapter plates (RGB 408) ................................... 2-13

Cabling and connections ..................................................... 2-14

Attaching cables to pass-through connectors .................. 2-14

Connecting shields .............................................................. 2-15

Connecting audio cables — RGB 404 ................................ 2-16

Connecting audio cables — RGB 406, RGB 408 ................ 2-18

Connecting input cables and video output cables ........... 2-18

Attaching power cables ...................................................... 2-18

Using installation cable ...................................................... 2-19

Pre-installation testing/troubleshooting ............................ 2-19

Mounting the interface to the wall box ............................ 2-21

Application diagrams .......................................................... 2-23

Appendix A • Specifications ................................................. A-1

Appendix B • Templates............................................................ B-1

RGB 406 Cut-out Template ................................................ B-2

RGB 404 Cut-out Template ................................................ B-3

RGB 408 Cut-out Template ................................................ B-4

iRGB 400 Series • Table of Contents

Page 4

Table of Contents, cont’d

Appendix C • Dimensions ........................................................ C-1

RGB 404 Panel Dimensions ............................................... C-2

RGB 406 Panel Dimensions ............................................... C-5

RGB 408 Panel Dimensions ............................................... C-6

RGB 408 Panel Dimension Details ................................. C-7

Appendix D • Accessories and Part Numbers .......... D-1

Interfaces and Included Parts ........................................ D-2

Accessories and Connectors ........................................... D-2

Cables ......................................................................................... D-3

Optional Adapter Plates ................................................... D-4

RGB 400 Series

Chapter One

Introduction

About this Manual

About The RGB 400 Series Interfaces

Features

68-364-01 D

Printed in the USA

RGB 400 Series • Table of Contents

07 00

Page 5

Introduction, cont’d

Introduction

About this Manual

This manual contains information about the RGB 400 Series interfaces and on how to operate and configure them.

About The RGB 400 Series Interfaces

The RGB 400 Series are 300 MHz (-3dB) bandwidth, analog computer-video interfaces that can be mounted in walls or furniture. The RGB 406 is two-gang wall plate size, the RGB 404 is three-gang size, and the RGB 408 is four-gang size. All are available with black, white, or gray panels.

Features

RGB 400 Series features

Horizontal centering control — Shifts the image horizontally.

Level control — Adjusts the image brightness.

Peaking control — Adjusts the image sharpness.

Sync output options — Six BNC connectors allow separate

horizontal, vertical and composite sync outputs. Sync-on-green (SOG) is output only if SOG is input.

Digital Display Sync Processing™ (DDSP™) — Sync is

output in its original state to ensure compatibility with digital display products.

75 ohm video termination switch — For applications

where a local computer monitor is not being used.

RGB 400 Series

Chapter Two

1-2

Additional RGB 404 features

The RGB 404 offers the following features in addition to the RGB 400 Series features listed above:

Composite video pass-through RCA connector

S-video pass-through 4-pin mini DIN connector

Network pass-through (RJ-45 connector)

Two 2-channel audio outputs (unbalanced in, balanced

out) on RCA and PC stereo connectors

Additional RGB 406 and RGB 408 features

The RGB 406 and RGB 408 offer these features in addition to the RGB 400 Series features listed above:

Two channels of audio (unbalanced in, balanced out)

Optional pass-through adapter plates (RGB 408 only)

RGB 400 Series • Introduction

Installation and Operation

Installation Overview

Installation and Operation Instructions

Page 6

Installation and Operation, cont’d

SHR Coax Cable

Approximately 3.3"

Approximately 2.5"

Circuit Board

Front Panel

Mini-Coax Cable

Installation and Operation

Installation Overview

To install and set up an RGB 400 Series interface, follow these basic steps:

Determine the installation location.

Prepare the site for installation. Use the supplied

template to mark the rough-in cutout, then cut out the wallboard or wood.

Set the DIP (dual in-line package) switches and

jumpers. These items will be inaccessible after installation.

For the RGB 408, attach optional adapter plates, and

attach output cables to the back sides of the adapter plates.

For all models, connect the wires and cables for

power, audio output and pass-through signals.

These items will be inaccessible after installation.

For all models, set the front panel High Z/75 Ohm

video termination toggle switch.

Temporarily connect the input cables. Connect any

cables whose signals will be routed through the optional adaptor pass-through plates.

Connect power cables to the input and output

devices. Turn on the input and output devices.

Installation and Operation Instructions

Determining installation location

Take cabling and power availability and the location of wall studs into consideration when selecting an installation site. You may need to install the cables in the wall, furniture or conduits before installing the interface. Choose a location that will allow cable runs without interference, preferably next to a 2” x 4” wall stud.

The RGB 400 Series interfaces each consist of a front panel with an attached circuit board. They are typically installed in standard 2-, 3- or 4-gang, 2.5-inch deep electrical wall boxes. A metal wall box (provided by Extron) is preferred, but a plastic box (or no wall box at all) can be used as long as it conforms to local code restrictions and the interface’s size requirements. If a wall box is used, it must be attached to wall studs within the wall.

The drawing below illustrates the typical depth required to accommodate the maximum bend of high resolution (SHR) coaxial and miniature coaxial cables inside a wall box.

2-2

RGB 400 Series • Installation and Operation

The image should now display on screen. If it does

not display, or if the picture displays incorrectly, double check and make adjustments to cables, DIP switches and jumpers as needed. Refer to the “Pre-installation testing/troubleshooting” section in this chapter.

Temporarily disconnect the input cables from the

front panel of the interface, and disconnect the power from the interface.

Mount the interface in the wall or furniture.

Reconnect the computer video and audio input

cables to the interface, apply power, and readjust horizontal centering as needed via the front panel control.

Minimum installation depth needed for maximum coaxial cable bend

Cut-out (rough-in) templates and dimensional drawings are provided in the appendices of this manual.

RGB 400 Series • Installation and Operation

2-3

Page 7

Installation and Operation, cont’d

Preparing the installation site and installing the wall box

Actual-size rough-in templates for each model are provided in Appendix B. If needed, make a 100% size photocopy of the appropriate template to use for installation. Compare the photocopy with the faceplate and wall box to make sure the photocopy size is the same as the equipment.

Use the template as a guide to mark and cut the hole in the wall or furniture through which the interface will be installed. The innermost line represents the opening where material will be removed and the wall box will be installed.

1. Cut out the center portion (up to the guidelines) of the cut-out (rough-in) template.

2. Place the template on the surface where the interface will be installed. Use a soft pencil to mark the guidelines for the opening on the wall/furniture.

3. Cut out the material from the cut-out area with a jigsaw or small hand saw.

4. Check the opening size by inserting the wall box (if used) or the interface (if no wall box is used) into the opening. The wall box will be mounted flush with the outer wall or furniture surface. The box and/or interface should fit easily into the opening.

5. If needed, use a saw, file or sandpaper to enlarge the hole. Smooth the edges of the opening to avoid damage or injury to yourself or the cables during installation.

6. Attach the wall box to the wall stud (2” x 4”) with nails or screws, leaving the front edge flush with the wall surface, as shown in the following illustration.

Wall Stud

Wall Box

Flush with

Screws or Nails

Wall Surface

Attaching the wall box to wall studs

To attach the wall box to wood, use four #8 to # 10 wood or sheet metal screws. A minimum of 1/2 inch (1.25 cm) of screw threads must penetrate the wood. If the wood is a 2 x 4, such as a wall stud, 10-penny or larger nails can be used.

To attach the electrical wall box to metal, use four #8 or #10 sheet metal screws (self-tapping) or #8 or #10 machine bolts with matching nuts.

7. Output cables will usually be out of sight inside a wall, for example. Feed the cables through the wall box “punch-out” holes for connection to the interface. Cable clamps should be used to hold the cables in place for strain relief.

8. Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate shields with heat shrink. Details for typical maximum coaxial cable bend inside a wall box are given on page 2-3.

9. Configure, cable and test the interface before securing the interface to the wall box. Configuration consists of setting circuit board DIP switches and jumpers based on installation requirements. See page 2-14 for more information.

2-4

RGB 400 Series • Installation and Operation

2-5

Page 8

Installation and Operation, cont’d

RGB 406/ RGB 408

Captive

Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V

.9V

.7V

.8V

.9V

BGR

CH1L CH1R CH1R

12345678910

Signal

Ground

CH1L

& CH1R outputs are

generated from RCA inputs.

CH2L

& CH2R outputs are

generated from 3.5 mm inputs.

RCA

3.5 mm

REV. A 79-08

33-323-01

J10

SW1

J11 J12

J13

95687

1718 19

10 11 12 14 1513

Black

RedYellow

Green

REAR

Front and rear panel (circuit board) features

RGB 404 front and rear features

INPUT

AUTO POWER

H. SHIFT

Extron

HIGH Z

75 Ohm

A U D

17 18

VIDEO

S-VIDEO

NETWORK

RGB 404

2 3 4

FRONT

567

Pin assignment label for the audio output captive screw

connector (item 9) — Audio output wiring is discussed in

Auto power LED — If active sync pulses are present, power

and this LED turn on. If not, power and this LED turn off.

H. Shift (horizontal shift) control — This controls the

horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB input.

High Z/75 Ohm switch — For proper video termination, set

this switch to 75 Ohms if no local monitor will be connected.

PC type 3.5 mm stereo audio input connector — This

Tip (+) Sleeve (GND)

connector is for unbalanced input to audio channel 2. Wire

2-6

RGB 400 Series • Installation and Operation

Ring (R, -)

Tip (L, +)

Sleeve (GND)

Left and right audio channel RCA connectors — These

connectors are for unbalanced input to audio channel 1. Wire the input plugs as shown below.

Tip

Network pass-through RJ-45 connector

Sleeve ( )

the input plug as shown here.

the cabling section of this chapter.

Audio output captive screw connector — Use this

connector for the balanced output from both audio channels (1 and 2). See the wiring diagram label (item 8) and the cabling section in this manual for wiring instructions.

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

SW1 DIP switches — 1. On = Removes serration pulses.

2. On = Enables Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on

the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wires — Splice these wires to a 12 to 24VAC or

VDC power source.

Composite video pass-through RCA connector—If unused,

this connector can be replaced with a 0.31” diam. plug.

S-video pass-through 4-pin mini DIN connector — This

connector can be replaced with a 0.50” diam. plug.

BNC output connectors — These 6 connectors are for video

and sync output. Connect the coax cables’ BNC connectors

as shown here for red, green and blue video output, and either separate

horizontal and vertical sync or composite sync.

RGB 400 Series • Installation and Operation

2-7

Page 9

Installation and Operation, cont’d

RGB 406 front and rear features

AUTO POWER

H. SHIFT

Extron

1 2 3

AUDIO

HIGH Z

75 Ohm

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

1. ON = Remove

SW1

RGB 406

serration pulses.

2. ON = Digital

display sync.

SW1

J13

321

J13

RGB 406/ RGB 408

Captive

Screw

Connector

67 910 12 1311

INPUT

FRONT REAR

Auto power LED — If this LED is on, power and sync

pulses are present. If no sync is present, power and this LED turn off.

H. Shift (horizontal shift) control — This controls

horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB

analog input.

Audio 3.5 mm stereo PC-type connector for unbalanced

input — See page 2-12 for an input plug wiring diagram.

High Z/75 Ohm switch — For proper video termination,

set this switch to 75 Ohms if no local monitor will be connected.

BNC output connectors — These 6 connectors are for

video and sync output. Connect the coaxial cables’ BNC

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

Audio output 3.5 mm, 5-pole captive screw connector —

connectors as shown here for red, green and blue video output, and

either separate horizontal and vertical sync or composite sync.

The label below this connector provides a wiring diagram for balanced audio output.

SW1 DIP switches —

1. On = Removes serration pulses.

J11 J12

2. On = Enables Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on

the label located below the circuit board.

J10

.8V

.9V

BGR

.7V

.8V

.7V

J10

.7V

.9V

J10

33-398-01 B 08 99

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wires — Splice these wires to a

12 to 24VAC or VDC power source.

2-8

RGB 400 Series • Installation and Operation

2-9

Page 10

Installation and Operation, cont’d

RGB 408 front and rear features

HIGH Z

75 Ohm

AUTO POWER

H. SHIFT

INPUT

AUDIO

Extron

1234 65

Auto power LED — If this LED is on, power and video

sync pulses are present. If no sync is present, power and this LED turn off.

H. Shift (horizontal shift) control — This controls

horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB

analog input.

Audio input 3.5 mm stereo PC-type connector for

unbalanced input — Wire the PC audio input plug as shown here.

Tip (+) Sleeve (GND)

High Z/75 Ohm switch — For proper video

termination, set this switch to 75 Ohms if no local monitor will be connected.

Architectural adapter plates installation bay — Up to

four adapter plates for pass-through audio/video connections can be attached at one time to the interface. See the “Attaching adapter plates” section in this chapter for installation instructions.

Ring (R, -)

Tip (L, +)

Sleeve (GND)

RGB 40 8

FRONT

REAR

SW1

J10

J13

1 = +5V 20 mA max.

321

2 = –5V 20 mA max. 3 = Ground

J13

RGB 406/

1. ON = Remove

SW1

BNC output connectors — These 6 connectors are for

RGB 408

serration pulses.

Captive

Screw

2. ON = Digital display sync.

Connector

78 1011 13 14

.8V

.9V

.7V

.8V

.7V

.9V

J10

video and sync output. Connect the coaxial cables’ BNC connectors as shown here for red, green and blue

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

Audio output 3.5 mm, 5-pole captive screw connector

video output, and either separate

horizontal and vertical sync or composite sync.

— The label below this connector provides a wiring diagram for balanced audio output.

SW1 DIP switches —

1. On = Remove serration pulses.

2. On = Enable Digital Display Sync Processing

(DDSP).

J10 blue gain/peaking jumper — Settings are shown on

the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wire — Splice these wires to a

12 to 24VAC or VDC power source.

33-398-01 B 08 99

J11 J12

BGR

J10

2-10

RGB 400 Series • Installation and Operation

2-11

Page 11

Installation and Operation, cont’d

Setting DIP switches and jumpers

DIP switches and jumpers must be set and tested before the interface is secured into the wall box, wall or furniture.

DIP switches

DIP switch module SW1 contains two DIP switches (SW1-1 and SW1-2). The module is located on the circuit board on

the back of the interface, as shown on pages 2-6,

SW1

2-7, 2-9, 2-11 and 2-13. In these illustrations, the

On position is to the left.

Different video projectors may have slightly different sync requirements. Use the DIP switches on the interface to make the interface’s output compatible with the projector.

DIP switch 1 (SW1-1) controls serration pulse output.

ON = No serration pulses will be output in the

composite sync signal.

OFF = Serration pulses will be output.

DIP switch 2 (SW1-2) controls sync processing.

ON = Digital Display Sync Processing (DDSP) will be

used. This may be required in order to obtain a stable picture on some digital display devices. When DDSP is on, horizontal shift (centering) is disabled.

OFF = DDSP will not be used.

Jumpers

Video signals passing through long cable runs (over 125 feet) or through poor quality cables can decrease in strength, creating signal loss. The longer the cable, the higher the video level and the greater the peaking that will be needed to compensate for the loss.

The gain/peaking adjustment jumpers are located on the circuit board on the back of the interface, as shown in the rear features sections of this manual. To configure the jumpers, use pliers to pull the jumper shunt off the pins, then place the jumper on the appropriate pins.

Make sure the interface is disconnected from the power source before configuring jumpers.

Changing jumper settings

Each red (J8), green (J9) and blue (J10) jumper can be set to one of three positions to provide unity gain (0.7 volts p-p),

0.8 volts p-p, or 0.9 volts p-p output. Select the setting that yields the best image display. Use the diagram on the product label (shown below) as a guide to setting the output gain/peaking for each color.

.8V

.9V

.8V

.7V

J10

.7V

.9V

.8V

.9V

RGB 400 Series gain/peaking jumpers

0.7V — Use this for short cable runs (under 125 feet).

0.8V — Use this for long cable runs for all frequencies.

0.9V — Use this setting for long cable runs and high frequency video signals.

Attaching adapter plates (RGB 408)

The RGB 408 can have up to 4 optional adapter plates. The adapter plates allow for a variety of types of pass-through audio and/or video connectors to be added to the interface’s front panel faceplate.

Blank plates (two single-height and one double-height plate) are included with the RGB 408 to cover unused spaces. Other adapter plates must be ordered separately. They also must be attached to the faceplate and cabled before the interface is installed in the wall or furniture. The screws needed for installing the adapter plates are built into the plates, so no additional screws will be needed.

1. Remove the blank plates from the interface by

unscrewing the nuts that fasten the plates to the faceplate.

2. Insert the adapter plate screws through the holes in

the faceplate. Attach the adapter plates to the faceplate with the provided captive washers and #4-40 nuts. See the illustration “Installing optional adapter plates” on the next page.

3. Attach the output cables to the connectors on the back

side of the adapter plates. Several adapter plates require conductors to be soldered to the connectors. Attach foil and braided shields to ground connections.

2-12

RGB 400 Series • Installation and Operation

2-13

Page 12

Installation and Operation, cont’d

Metal Wall Box

Screw

Braided Shield

Install Cable

Foil Shield

Cable Clamp

INPUT

AUTO POWER

75 O

Installing optional adapter plates

AUDIO

. S

RGB 408

Adapter Plate

#4-40 Nut w/Captive Washer

RGB 408 (Up to 4 Plates)

Cabling RCA connectors

For composite video, solder the center conductor of a coaxial cable to the central solder cup of the RCA connector. Solder the cable’s shield to the grounded grounding tab. See the leftmost and center illustrations below.

Center Conductor

Shield

Central Solder Cup

Grounding Tab

RCA ConnectorCoaxial Cable Twisted Pair

Attaching coaxial and twisted-pair cables to RCA connectors

2-14

Cabling and connections

Attaching cables to pass-through connectors

The RGB 404 provides pass-through connectors for composite video, S-video, RJ-45 network These connectors are mounted on the faceplate. The RJ-45 cable can be plugged in from the back. Coaxial cables and/or twisted pair wires must be soldered to the back side of the S-video and RCA connectors, as described in this section.

Optional adapter plates with various types and combinations of pass-through audio and video connectors are available for the RGB 408. Many adapter plates also require cables and wires to be soldered to the rear connectors.

Cabling S-video connectors

The illustration below identifies the S-video connector signal leads. For the RGB 404, splice and solder the four

Luminance signal

Yellow

Black

Luminance ground

Chrominance

signal

Red

Shield tab

Green

Chrominance

ground

S-video connector wiring diagram

RGB 400 Series • Installation and Operation

wires from this connector to user-supplied coaxial cables. Insulate the soldered connections to prevent shorts. You can also use the connector’s shield tabs for chrominance and luminance ground tie points.

For audio, solder the signal wire of a shielded twisted-pair cable to the central solder cup of the RCA connector. Solder the ground wire to the grounded tab, as shown above at right.

Connecting shields

Multiconductor cables such as Extron’s Install Plenum bulk cable contain several braided and foil shields. At the interface end of the cable, the outer braided and foil shields should be connected to the grounded metal wall box (or to a grounding wire if a metal wall box is not used). The wires that make up the braided shield can be unbraided, then twisted together to form a large, multistrand wire that can be folded back under the wall box cable clamp or attached to the metal wall box with a screw. See the illustration below.

To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp. Both the braided and foil shields should be connected to an equipment ground at the other end of the cable.

Grounding outer braided and foil shields

RGB 400 Series • Installation and Operation

2-15

Page 13

Installation and Operation, cont’d

RGB 404 RGB 406 and RGB 408

Base

Ground/Shield

Circuit Board Circuit Board

If shielded twisted-pair wires are used for audio output for the RGB 404, RGB 406 or RGB 408, the shields should be connected to either pin 3 (RGB 406/408) or pins 3 and 8 (RGB 404) of the audio output captive screw connector. Twist the wires from the braided shield together to form a multi-strand wire, then insert it into the receptacle side of the captive screw connector. See the “Wiring audio output captive screw connectors” illustration on the next page.

Twisted-pair shields are not used for most other RGB 400 Series applications, even when twisted-pair wires are used. For those other applications, twist the shields together, and fold them back under the wall box cable clamp or attach them to the grounded wall box with a screw.

To prevent short circuits, unused shielded twisted-pair wires and exposed cable shields (braided or foil) must be insulated with electrical tape or heat shrink, and secured.

Connect coaxial cables’ shields to a ground through the individual connectors (BNC, S-video or RCA).

Connecting audio cables — RGB 404

The RGB 404 creates two 2-channel, balanced audio outputs from two unbalanced inputs.

• Audio channel one (CH1) consists of unbalanced input on two RCA input connectors (one each for left and

right input), and balanced output on pins 1 – 5 of the 10-pole audio

Tip

Sleeve ( )

captive screw connector on the rear of the circuit board. Wire the RCA input plugs as shown at left.

signal. For example, the input signals from the left side of channel one (CH1L) are output as CH1L+ and CH1L-. The following illustration shows the audio inputs and outputs and how to wire the audio connectors.

MaleFemale

Base

GND

Channel 1

from Audio L, R

RCA

Connectors

Channel 2

from PC

3.5mm

Connector

Circuit Board

Channel 1

Channel 2

GND

Captive Screw

Connector

Wiring RGB 404 audio connectors

To wire the audio output captive screw connector, follow these steps:

1. Prepare the wires for insertion into the connector by trimming off 3/16 inch of insulation.

2. Following the wiring diagram found on the label on the back of the faceplate or in this manual, insert the wires one at a time into the connector.

3. Tighten the wire clamp in the connector by turning the appropriate screw clockwise. Do not overtighten the screw. Avoid touching circuit board components with the ends of the wires. See the illustration below.

2-16

• Audio channel two (CH2) consists of unbalanced left and right input from the single PC-type 3.5 mm audio plug, and balanced output on pins 6 – 10 of the 10pole captive screw connector on the rear of the circuit board. Wire the stereo PC input plug as shown here:

Tip (+) Sleeve (GND)

Ring (R, -)

Tip (L, +)

Sleeve (GND)

The audio signals are converted from unbalanced to balanced signals as they pass through the RGB 404. As a result, two output signals are produced for each input

RGB 400 Series • Installation and Operation

Wiring audio output captive screw connectors

4. The cable shields should be connected to either pins 3 and 8 (RGB 404) or pin 3 (RGB 406/408) of the audio

RGB 400 Series • Installation and Operation

2-17

Page 14

Installation and Operation, cont’d

Double Shielded Foil and Copper Strand

Center Conductor (Stranded)

Sheath

Plenum Jacket, Double Shielded

Foil and Copper Strand

Polyethylene Foam

Four Sets of Twisted Pair (Stranded), Wire Braid Shield

Six Mini, High-resolution

Coaxial Conductors

17-Conductor Install Plenum Cable

Three 20-gauge Wires

Red & Black Twisted Pair

White & Black Twisted Pair

20 Gauge Violet

Yellow Mini-Coax

White Mini-Coax

20 Gauge Gray

Yellow

Green

Red

Black

RGB 404 Rear

Black Mini-Coax

Blue Mini-Coax

Green Mini-Coax

Red Mini-Coax

Shield to Black

Shield to Green

2-18

RGB 400 Series • Installation and Operation

output captive screw connector. See “Connecting shields” earlier in this chapter for details.

Connecting audio cables — RGB 406, RGB 408

Each RGB 406 or RGB 408 accepts an unbalanced audio input from a front panel 3.5 mm PC-type stereo connector, and it outputs two channels of balanced audio on a 3.5 mm, 5-pole captive screw connector on the rear of the circuit

12345

board. Follow the steps listed for the RGB 404 for inserting wires into captive screw connectors. Use the label on the rear of the faceplate (excerpted here) as a wiring guide.

Connecting input cables and video output cables

With appropriate cables, connect the computer and audio device(s) to the interface via the front panel input connectors. Connect all the devices for pass-through input (network, composite video, S-video and/or other inputs) via front panel or front adapter plate connectors.

Determine what computer-video format the display device requires: separate horizontal and vertical sync (RGBHV), composite sync (RGBS), or sync on green (RGsB or SOG). No matter what format the computer outputs to the interface, the output from the interface to the display device can be RGBHV or RGBS. If the video format input to the interface is RGsB (SOG), RGsB can be output to the display device; otherwise only RGBHV and RGBS are available as output options.

Connect the display device to the interface using coaxial cables. Attach the cable’s BNC connectors to the appropriate rear panel BNC connectors on the interface based on the video format required by the display device.

Attaching power cables

Each RGB 400 Series interface requires an external voltage source of 12 to 24 volts AC or DC (250 mA maximum, 5 W). The interfaces are supplied with a power cord of twistedpair wire soldered to the circuit board.

1. Splice these wires to the cord of a user-supplied power source. Polarity is not important, even if the power source supplies DC voltage. Extron offers an optional external power supply. See Appendix D for the part number.

2. Solder and insulate the connections.

Using installation cable

Extron’s Install Plenum bulk cable (shown here) is ideal for mountable interfaces such as the RGB 400 Series models.

Below is an example of how the cable can be used.

Using installation cable with an RGB 404

Pre-installation testing/troubleshooting

Before installing the interface into the wall or furniture, test the system to make sure that the connections and interface settings are correct.

Turn on the input device(s) (computer, audio device) and output device(s) (projector and/or monitor, speakers). The image should now appear on the screen, and sound should be audible.

If the image does not appear or there is no sound

1. Ensure that all devices are plugged in.

2. Make sure that each device is receiving power. The

interface’s Auto power indicator LED will light if the interface is receiving power and an active sync signal.

RGB 400 Series • Installation and Operation

2-19

Page 15

Installation and Operation, cont’d

EMI Strips

4-gang Wall Box

EMI Strip

Remove Adhesive Backing

RGB 408

INPUT

HIGH Z

AUDIO

75 Ohm

RGB 408

3. Check the cabling and the audio connector wiring, and make adjustments as needed.

4. Verify that the High Z/75 Ohm video input termination toggle switch on the front panel has been set correctly.

5. For digital display devices (including LCD, DLP and plasma devices), try turning DDSP on or off using the rear panel SW1-2 DIP switch.

6. Call Extron’s customer support hotline if needed.

If the image does not display correctly

1. If the output image looks too green, the computer may be sending video with sync on green (SOG), and the display device may not be configured to handle SOG signals. The RGB 400 Series interfaces do not strip sync from the video input signals.

2. If the picture bends or flags at the top of the screen, set the serration pulse DIP switch (SW1-1) to Off.

3. For a display device that experiences intermittent glitches, try turning DDSP on or off using the rear panel SW1-2 DIP switch.

4. If the picture “hangs off” the edges of the screen, adjust the H. Shift horizontal centering control.

5. If the edges of the image seem to exceed their boundaries or if thin lines and sharp edges look thick and fuzzy, try changing the gain/peaking jumper (J10, J9, J8) settings. If the image is too bright, decrease the gain/peaking level.

6. If the image appears and is stable, but it has ghosting or blooming, check the High Z/75 Ohm video input termination. If changing the termination doesn’t solve the problem, try using a different input cable.

7. If the image still does not display correctly, call Extron’s customer support hotline.

the situation, either the pass-through connector or any cable that was part of the installation but not used for this test may be the source of the problem. If this test does not produce an image or sound, the problem may lie with an input device or an output device.

Mounting the interface to the wall box

Once the system has been cabled and tested, the interface can be installed in the wall or furniture.

1. Remove power from the interface and input and output devices by disconnecting the power cords from the power supply.

2. Detach the input cables from the front panel.

3. For the RGB 408 only, install the EMI strips.

To maintain proper grounding connections between the interface faceplate and the wall box, adequate contact between the faceplate and wall box must be ensured. Installing the supplied EMI (electromagnetic interference) strips will ensure the proper contact and maintain the ground. To install the strips, do the following:

a. Peel off the protective, papery coating from the

back of an EMI strip.

b. Apply the EMI strip to the center of the upper lip

of the 4-gang wall box, pressing firmly to ensure contact. See the illustration below.

c. Repeat steps 1 and 2 to install the other EMI con-

ductive strip onto the lower lip of the wall box.

2-20

If no image or sound results from pass-through connections

1. Make sure each input device is connected to the correct pass-through connector, which in turn is connected to the appropriate output device.

2. Ensure that each connector is properly wired and grounded, and that each device is powered on.

3. If there still is no image or sound, try cabling the input device directly to the output device. If that resolves

RGB 400 Series • Installation and Operation

Installing EMI strips on the wall box

RGB 400 Series • Installation and Operation

2-21

Page 16

Installation and Operation, cont’d

4. For all models, carefully place the interface through the opening in the wall or furniture and into the wall box (if one is used). Take care not to damage the cables.

5. Mount the interface faceplate to the wall box with the provided machine screws (as shown below), or attach the interface directly to the furniture with wood or metal screws.

Cable Clamp

S-VIDEO

VIDEO

HIGH Z

A U D I

NETWORK

75 Ohm

INPUT

Install Cable

Application diagrams

Below are examples of typical system installations that incorporate RGB 400 series interfaces. Many other configurations are possible. Extron offers a variety of laptop and monitor breakout cables for easy connection of PCs, Macintosh, Sun or SGI computers.

INPUT

AUTO POWER

H. SHIFT

Extron

LBC Cable

Laptop Computer

An RGB 404 application featuring a laptop and network and S-video pass-through connections

VIDEO

HIGH Z

75 Ohm

U D

NETWORK

RJ45 Network

Cable

Video Cassette Player

S-VIDEO

RGB 404

2-22

Mounting the interface to the wall box

6. Reconnect the input cables to the interface via the front panel connectors.

7. Reconnect the power cables and restore power to the equipment.

RGB 400 Series • Installation and Operation

RGB 404

HIGH Z

INPUT

AUTO POWER

H. SHIFT

Extron

75 Ohm

AUDIO

RGB 406

MBC Cable Audio Cable

SVGA Compatible

Computer w/ Audio

A typical RGB 406 application

RGB 400 Series • Installation and Operation

2-23

Page 17

Installation and Operation, cont’d

RGB 400 Series

Appendix A

2-24

Specifications

RGB 400 Series • Installation and Operation

Page 18

Specifications, cont’d

Specifications

These specifications apply to all models unless otherwise noted.

Video input

Number/type ............................... 1 analog RGBHV, RGBS, RGsB

Connectors .................................... 1 9-pin male D connector for

MBC/LBC cable or buffer

Nominal level(s) .......................... Analog ....... 0.3V to 1.45V p-p

Impedance .................................... 75 ohms or Hi Z, switchable (set to

75 ohms if no local monitor is connected)

Horizontal frequency .................. 15 kHz to 150 kHz

(optimum 15 kHz to 62 kHz)

Vertical frequency ....................... 30 Hz to 170 Hz

Return loss .................................... -30dB @ 5 MHz

Video throughput

Gain ............................................... Unity (0.7V), 15% with 3dB peaking (0.8V),

30% with 6dB peaking (0.9V)

Bandwidth .................................... 300 MHz (-3dB)

Video output

Number/type/format ................ 1 analog RGBHV, RGBS, RGsB

Connectors .................................... 6 BNC female

Nominal level ............................... Analog ....... 0.7V p-p, 0.8V p-p, or

0.9V p-p (internal jumper-

selectable) w/peaking

Impedance .................................... 75 ohms

Return loss .................................... -30dB @ 5 MHz

Sync

Input type ..................................... Autodetect RGBHV, RGBS, RGsB (accepts

RGsB but does not strip from video)

Output type .................................. RGBHV ...... at all times

RGBS .......... at all times

RGsB .......... only when input is RGsB

Input level ..................................... 2.0V to 5.5V p-p with

Output level .................................. 4.0V to 5.0V p-p

Input impedance .......................... 10 kohms

Output impedance ....................... 75 ohms

Max propagation delay ............... 50 nS

Max rise/fall time ........................ 2.5 nS

Polarity .......................................... Positive or negative

+0.2VDC offset max.

Audio input — RGB 404

Number/type ............................... 2 stereo, unbalanced; 1.0Vrms (+4dBu),

20 Hz to 20 kHz

Connectors .................................... Ch. 1 ........... 2 RCA female jacks

Ch. 2 ........... 3.5 mm stereo female jack

(2 channel), unbalanced;

tip (L), ring (R), sleeve (gnd)

Impedance .................................... 10 kohms, DC coupled

Minimum level ............................. 100mV

Maximum level ............................ +8.5dBu

Audio input — RGB 406 and RGB 408

Number/type ............................... 1 stereo, unbalanced; 1.0Vrms (+4dBu),

20 Hz to 20 kHz

Connectors .................................... 3.5 mm stereo female jack (2 channel),

unbalanced; tip (L), ring (R), sleeve (gnd)

Impedance .................................... 10 kohms, DC coupled

Minimum level ............................. 100mV

Maximum level ............................ +8.5dBu

Audio throughput — RGB 404 (channels 1 and 2), RGB 406 and RGB 408

Gain ............................................... Unbalanced 0dB, balanced +6dB

Response ....................................... ±0.5dB @ 20 Hz to 20 kHz

THD + Noise ................................ 0.03% @1 kHz, 0.3% @ 20 kHz

at rated maximum output drive

S/N ................................................ >90dB, output 14dBu, balanced

Stereo channel separation ........... >95dB @ 1 kHz to 20 kHz

Audio output — RGB 404 (channels 1 and 2)

Number/type ............................... 2 buffered, stereo (2 channel),

balanced/unbalanced

Connectors .................................... 3.5 mm captive screw terminal,

5 conductor

Impedance .................................... 50 ohms unbalanced, 100 ohms balanced

Gain error ...................................... ±0.1dB channel to channel

Drive (600 ohm) ........................... +14dBu, balanced at stated %THD+N

Audio output — RGB 406 and RGB 408

Number/type ............................... 1 buffered, stereo (2 channel),

balanced/unbalanced

Connectors .................................... 3.5 mm captive screw terminal, 5 conductor

A-2

RGB 400 Series • Specifications

A-3

Page 19

Specifications, cont’d

Impedance .................................... 50 ohms, unbalanced, 100 ohms balanced

Gain error ...................................... ±0.1dB channel to channel

Drive (600 ohm) ........................... +14dBu, balanced at stated %THD+N

General

Power ............................................. 12 to 24VAC or VDC, 0.25 A, 5 watts,

external (Order the power supply separately.)

Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /

10% to 90%, non condensing Operating +32° to +122°F (0° to +50°C) /

10% to 90%, non condensing

Rack mount ................................... No, but wall or furniture mountable

Enclosure type .............................. Metal

Enclosure dimensions (RGB RGB 404)

Plate ................................... 4.50” H x 6.40” W

(11.43 cm H x 16.26 cm W)

Box ..................................... 3.75" H x 5.3" W x 2.5" D

(9.5 cm H x 14.2 cm W x 6.35 cm D) 3-gang

Interface ............................. 2.8" H x 5.3" W x 2.5” D

(7.1 cm H x 13.5 cm W x 6.4 cm D)

(depth is given with an HR cable attached) Enclosure dimensions (RGB 406)

Plate ................................... 4.50” H x 4.60” W

(11.43 cm H x 11.68 cm W)

Box ..................................... 3.75" H x 3.75" W x 2.5" D

(9.5 cm H x 9.5 cm W x 6.35 cm D) 2-gang

Interface ............................. 2.8" H x 3.5" W x 2.5” D

(7.1 cm H x 8.9 cm W x 6.4 cm D)

(depth is given for the circuit board with

an HR cable attached) Enclosure dimensions (RGB 408)

Plate ................................... 4.50” H x 8.33” W

(11.43 cm H x 21.15 cm W)

Box ..................................... 3.75" H x 7.38" W x 2.50" D

(9.50 cm H x 18.73 cm W x 6.35 cm D) 4-gang

Interface ............................. 2.8" H x 3.5" W x 2.5” D

(7.1 cm H x 8.9 cm W x 6.4 cm D)

(depth is given for the circuit board

with an HR cable attached)

Shipping weight (all models) ..... 3 lbs (1.4 kg)

Vibration ....................................... NSTA 1A in carton

(National Safe Transit Association)

Approvals ..................................... UL, CE, FCC Class A

MTBF ............................................. 30,000 hours

Warranty ....................................... 2 years parts and labor

Specifications are subject to change without notice.

A-4

RGB 400 Series • Specifications

A-5

Page 20

Specifications, cont’d

RGB 400 Series

Appendix B

A-6

Templates

RGB 406 Cut-out Template

RGB 404 Cut-out Template

RGB 408 Cut-out Template

RGB 400 Series • Specifications

Page 21

Templates, cont’d

Templates

All the templates in this section are actual size. Also, they all include the recommended 0.1” (0.25 cm) clearance on all sides of the electrical wall box to allow room for the raised areas surrounding the knockouts.

The dashed line in each template indicates the cut-out area for installing a wall box. If you plan to install the interface without a wall box, use the smaller cut-out area indicated by the dotted lines.

RGB 406 Cut-out Template

Use this template as a guide for cutting a hole in a wall or furniture for the 2-gang size electrical box in order to install an RGB 406.

a wall box,

RGB 404 Cut-out Template

Use this template for cutting a hole in a wall or furniture for the 3-gang size electrical box for an RGB 404.

a wall box,

without

use the cut-out area (3.00"H)

To install the interface

indicated by the dotted line.

B-2

the rear of the RGB 406 front panel.

electrical box (3.75"H x 3.75"W) against

The light gray area represents the layout of the

RGB 400 Series • Templates

without

indicated by the dotted line.

use the cut-out area (3.00"H)

To install the interface

the electrical wall box.

area (3.95"H x 3.95"W) for installing

The dashed line indicates the cut-out

the rear of the RGB 404 front panel.

electrical box (3.75"H x 5.60"W) against

The light gray area represents the layout of the

RGB 400 Series • Templates

the electrical wall box.

(3.95"H x 5.80"W) for installing

The dashed line indicates the cut-out area

B-3

Page 22

Templates, cont’d

a wall box,

without

indicated by the dotted line.

use the cut-out area (3.00"H)

To install the interface

RGB 400 Series

Appendix C

B-4

against the rear of the RGB 408 front panel.

The light gray area represents the layout of the electrical box (3.75"H x 7.38"W)

Use this template for cutting a hole in a wall or

furniture for the electrical box and pass-through

RGB 408 Cut-out Template

RGB 400 Series • Templates

connections for the 4-gang size RGB 408.

for installing the electrical wall box.

The dashed line indicates the cut-out area (3.95"H x 7.58"W)

Dimensions

RGB 404 Panel Dimensions

RGB 406 Panel Dimensions

RGB 408 Panel Dimensions

RGB 408 Panel Dimension Details

Page 23

Dimensions, cont’d

Dimensions

The diagrams in this appendix have been reduced to fit on the pages. All dimensions are given in inches. The symbol “ø” indicates a diameter.

RGB 404 Panel Dimensions

HAND SAND TO

0.06" RADIUS

AROUND TOP EDGES.

REQ'D

(2 PLACES MARKED B)

STANDOFFS: 2

ø.213 THRU

DETAIL B

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

DETAIL A

REQ'D 2

ø.085 THRU

(2 PLACES)

DETAIL B

(3 PLACES

MARKED C)

ø.323 THRU

S- VIDEO

VIDEO

AUD

HIGH Z

75 Ohm

INPUT

SCALE: 2/1

ø.236 THRU

C'BORE ø.400

x .060 DEEP

DETAIL C

404

RGB

NETWORK

DETAIL C

ø.156 THRU

C'SINK ø.290 x 82˚

ø.111

(VIEWED FROM BACK SIDE)

(4 PLACES)

PLACES MARKED E ) 4 (

RGB 406 Panel Dimensions

DETAIL A

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

REQ'D

STANDOFFS:

ø.213 THRU

(2 PLACES MARKED 'b')

DETAIL B

HIGH Z

INPUT

DETAIL C

75 Ohm

AUTO POWER

ø.200

AUDIO

.184

H. SHIFT

.06

DETAIL B

406

RGB

Extron

THRU ø.240

ø.400

DETAIL C

ø.156 THRU

WITH C'SINK ø.290 x 82˚

ON NEAR SIDE (4 PLACES MARKED ' ' )

C-2

DETAIL A

RGB 400 Series • Dimensions

AUTO POWER

ø.125 THRU

ø.230 THRU

H. SHIFT

Extron

HAND SAND TO 0.06" RADIUS

AROUND THE TOP OF

THESE EDGES.

DETAIL A

ø.230 THRU

ø.125 THRU

RGB 400 Series • Dimensions

C-3

Page 24

Dimensions, cont’d

RGB 408 Panel Dimensions

2.250

REQ'D

STANDOFFS:

ø.213 THRU

(2 PLACES MARKED 'b')

Ohm

HIGH

DETAIL B DETAIL D

RGB 408 Panel Dimension Details

R 0.250

(4 PLCS)

8.325

1.405

RGB 408

ø.156 THRU

WITH C'SINK

ø.290 x 82˚ ON NEAR SIDE

(4 PLACES MARKED ' ' )

6.881

6.025

ø 0.170 THRU (8 PLACES)

R 0.050 (4 PLACES)

1.760

1.370

3.844

3.104

DETAIL C

3.520

2.740

0.040 DEEP RECESS

1.050

2.100

2.810

0.700

0.350

1.500

3.000

DETAIL D

HAND SAND TO 0.06" RADIUS

AROUND THE TOP OF

THESE EDGES.

C-4

INPUT

2.175

4.500

3.891

3.450

2.280

DETAIL A

RGB 400 Series • Dimensions

AUTO POWER

ø 0.125 THRU

ø 0.230 THRU

AUDIO

1.140

1.395

1.050

1.055

H. SHIFT

0.609

Extron

0.000

2.174

1.929

1.444

1.154

0.744

0.000

4– R .132

.403

.449

.225

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

DETAIL A

1.375

2.750

.06

.190

ø.201

DETAIL B

RGB 400 Series • Dimensions

THRU

ø.240

ø.400

DETAIL C

C-5

Page 25

Dimensions, cont’d

RGB 400 Series

Appendix D

C-6

Accessories and Part Numbers

Interfaces and Included Parts

Accessories and Connectors

Cables

Optional Adapter Plates

RGB 400 Series • Dimensions

Page 26

Part Numbers and Accessories, cont’d

Part Numbers and Accessories

Interfaces and Included Parts

This section lists the interfaces and the main parts that are shipped with each model. All models include:

• this manual, part number 68-364-01,

• one standard cable clamp with two machine screws, and

• four 3/8 inch, flathead screws (for attaching the faceplate).

Interfaces and included parts Part number

RGB 404G (gray faceplate) 60-237-01 RGB 404B (black faceplate) 60-237-02 RGB 404W (white faceplate) 60-237-03

0.31” diameter plastic plug (1) *

0.50” diameter plastic plug (1) *

3.5 mm, 10-pole captive screw connector 10-319-11

RGB 406G (gray faceplate) 60-249-01 RGB 406B (black faceplate) 60-249-02 RGB 406W (white faceplate) 60-249-03

RGB 408G (gray faceplate) 60-307-01 RGB 408B (black faceplate) 60-307-02 RGB 408W (white faceplate) 60-307-03 EMI strips (two, 4-inch) 100-107-01 Blank, single-height adapter plates 70-090-01/-11/-21 Blank, double-height adapter plate 70-090-02/-12/-22

* These plugs can replace unused pass-through connectors.

Cables

Monitor breakout cables Part number

MBC VGA/XGA HR 26-162-01 MBC Mac/Quadra 26-018-02 MBC Sun/Sparc HR 26-424-01 MBC SGI/13W3 HR 26-425-01

Below is a listing of some of the laptop breakout cables and other cables available for use with RGB 400 Series interfaces. A variety of lengths is available for each type of cable. See the Extron product catalog or call Extron’s support hotline for details.

Laptop breakout cables Part number

LBC VGA HR 3’ 26-224-02 LBC VGA HR 6’ 26-224-01 LBC VGA HR 12’ 26-224-03 LBC Mac HR 6’ 26-363-01 LBC Sun HR 6’ (61 kHz) 26-413-01 LBC Sun HR 6’ (71 kHz) 26-413-02 LBC Sun HR 6’ (81 kHz) 26-413-03 LBC Mac/VGA HR 26-394-01

Accessories and Connectors

Accessories/connectors Part number

12VDC, 1A external power supply

(from 100 to 240 VAC, 50/60 Hz) 70-055-01

3.5 mm, 5-pole captive screw connector 10-319-10 BNC mini HR crimp connectors (qty. = 50) 100-074-51 BNC SHR crimp connectors (qty. = 50) 100-075-51 BNC bulkhead connectors (qty. = 50)

(for custom wallplates) 100-076-51

BNC 5½” extension male-female

mini HR RGBHV 5 cable kit 70-113-01

D-2

RGB 400 Series • Part Numbers and Accessories

Laptop breakout cables w/audio Part number

LBC VGA HR 3’A 26-441-01 LBC VGA HR 6’A 26-441-02 LBC VGA HR 12’A 26-441-03

LBC Mac HR 6’A 26-442-02 LBC Sun HR 6’A (61 kHz) 26-443-02 LBC Sun HR 6’A (71 kHz) 26-444-02 LBC Sun HR 6’A (81 kHz) 26-445-02

Bulk cables (without connectors) Part number

Bulk SHR-1, 500’ 22-098-02 Bulk SHR-4, 500’ 22-099-02 Bulk SHR-5, 500’ 22-100-02 Bulk BNC 4-500’ mini HR 22-032-02 Bulk BNC 5-500’ mini HR 22-020-02 Bulk plenum BNC-5 mini HRP, 500’ 22-103-02 Bulk plenum 17-conductor installation, 500’ 22-111-03

RGB 400 Series • Part Numbers and Accessories

D-3

Page 27

Part Numbers and Accessories, cont’d

Pre-cut cables

BNC-5 cables are primarily used for applications that require RGBHV signals. BNC-4 cables are mainly used for RGBS signals. Either can be used to route composite video, S-video or RGB with sync on green. All of these cables come in lengths from 3 feet to 300 feet, and all have male BNC connectors on both ends. The BNC-5 HR cables are also available in a plenum version.

yarG kcalB etihW

Pre-cut high resolution cables Part number

BNC-4-25’MHR (25 feet/7.5 meters) 26-210-04 BNC-4-300’MHR (300 feet/90.0 meters) 26-210-53 BNC-5-25’MHR (25 feet/7.5 meters) 26-260-03 BNC-5-300’MHR (300 feet/90.0 meters) 26-260-14

Optional Adapter Plates

A variety of optional adapter plates for pass-through connections may be ordered for the RGB 408 interface. The RGB 408 can have up to 4 adapter plates installed in one of the following configurations:

• four adapter plates with a “plate size” of one,

• two adapter plates with a plate size of one and one

adapter plate with a plate size of two,

• or two adapter plates with a plate size of two.

The RGB 408 is shipped with two single height blank plates (part #70-090-01/-11/-21) and one double height blank plate (part #70-090-02/-12/-22).

The tables on the following page list some of the available adapter plates. Contact Extron for a complete list.

Blank Plate (no connector)

Single Space

2 - BNC

3 - BNC

Blank Plate (no connector)

Double Space

5 - BNC (Double)

setalPretpadAlarutcetihcrArotcennoCepyTelgniS

spucredlos601-0710-11-12-

epytrotcennoctnorF epytrotcennocraeR #traP

etalP

ezis

)elamefotelamef(lerrabCNBotACR21)kcalb/der(elamefACRelamefCNB490-0710-11-12-

)elamefotelamef(lerrabCNB21elamefCNBelamefCNB190-0710-11-12-

)elamefotelamef(lerrabCNB31elamefCNBelamefCNB190-0720-21-22-

noitpircsedetalpretpadA

)elamefotelamef(lerrabCNB52elamefCNBelamefCNB190-0730-31-32-

).mefot.mef(lerraboediv-Sotoediv-S21elamefNIDinimnip-4elamefNIDinimnip-4590-0710-11-12-

)elamefotelamef(lerrabCNBotACR31)kcalb/der(elamefACRelamefCNB490-0720-21-22-

elamefoeretsinimmm5.321elamefoeretsinimmm5.3slanimretgulredlos3890-0710-11-12-

elamefonohpoerets"¼21elamefonohpoerets"¼ slanimretgulredlos3790-0710-11-12-

)elamefotelamef(51-DH11elamefDHnip-51elamefDHnip-51101-0710-11-12-

)elamefotelamef(54-JR22elamef54-JRelamef54-JR001-0710-11-12-

)elamefotelamef(9-D11elamefDnip-9elamefDnip-9201-0710-11-12-

)esuom/draobyek(NIDinimnip-621elamefNIDinimnip-6elamefNIDinimnip-6401-0710-11-12-

elamefRLXnip-312elamefRLXnip-3slanimretgulredlos3301-0710-11-12-

dnahctiwserusolctcatnoc

kcajoeretsinimmm5.3

lanimretwercsevitpacelop5,mm5.311wercsevitpacelop5,mm5.3spucredlos501-0710-11-12-

em-wohsDEL/hctiwserusolctcatnoc1

kcajinimoeretsmm5.3dna

D-4

2 - RCA to Solder Cups

3 - RCA to Solder Cups

2 - S-video

2 - RJ-11

1 - D-9 Pass Through Connector

Architectural adapter plates

RGB 400 Series • Part Numbers and Accessories

D-5

Page 28

Part Numbers and Accessories, cont’d

kcalB etihW

setalPretpadAlarutcetihcrArotcennoCepyTitluM

#traP yarG

elamefNIDinimnip-4

epytrotcennoc

raeR

801-0720-21-22-

701-0720-21-22-

elamefACRdna

dnaelamefCNB

spucredlos3

dnaelamefNIDinimnip-4

epytrotcennoc

kcajoeretsinimmm5.3

dnaelamefCNB

elamefACR

tnorF

etalP

ezis

noitpircsedetalpretpadA

elamefACR3dnaelamefoediv-S12

kcajoeretsinimmm5.31

dnaelamefCNB1

RGB 400 Series • Part Numbers and Accessories

D-7D-6

Page 29

Part Numbers and Accessories, cont’d

D-8

RGB 400 Series • Part Numbers and Accessories