Extron DVS 510 SA, DVS 510 User Manual
Product Category
DVS 510 Series • Setup Guide
The Extron DVS 510 Series scalers are 10-input, multi-format presentation switching scalers that accept and scale DVI,
RGB, YUVp/HDTV, YUVi, S-video, and composite video signals to a common high-resolution output rate. Two models are
available: the standard DVS 510, which has fixed and variable line level audio outputs, and the DVS 510 SA, which adds an
integrated stereo amplifier. Control options include front panel buttons and knobs, Ethernet, RS-232 or RS-422, web pages,
and infrared (IR). This guide provides instructions for an experienced installer to install and connect the DVS 510 scalers.
NOTE: For full installation, configuration, and operation details, see the DVS 510 Series User Guide, available at
www.extron.com.
Rear Panel Features and Connections
V
I
D
E
O
O
U
T
P
U
T
6
RGB/R-Y, Y, B-Y
RGB/R-Y, Y, B-Y
7
DVI-D
Audio input connectors
h
Amplified audio output connector (DVS 510 SA only)
i
Variable audio output connector
j
Fixed audio output connector
k
Reset LED
l
1
100-240V 50-60 Hz
2A MAX
AC power connector
a
Video inputs 1 and 2: Composite video
b
Video inputs 3 and 4: S-video
c
Video inputs 5 and 6: RGB or YUV component
d
Video inputs 7/8 and 9/10: RGB or YUV (7 and 9) and
e
V
I
D
E
O
I
N
P
U
T
2
3
123
VID
VID
RGB/R-Y, Y, B-Y
YC
YC DVI-I
RGB/R-Y, Y, B-Y
4
4
5
67/8 9/10
5
DVI-I
DVI (8 and 10) m Reset button
Buffered RGB/YUV output connectors
f
DVI-I output connector (digital output only)
g
LAN connector
n
RS-232/RS-422 connector
o
Installation Steps
1. Disconnect power from all equipment.
2. (Optional) Mount the unit. Rack mount the scaler using the
attached brackets (see the illustration at right). For tabletop
placement, remove the brackets from the right and left sides
and attach the provided rubber feet.
3. Connect video inputs. Connect video input devices to the
appropriate connectors in the rear panel Video Input section
(b through e in the diagram above).
z Video inputs 5 and 6: RGB or YUV component —
Connect one or two RGBHV, RGBS, RGsB, RGBcvS, YUVi,
or YUVp/HDTV video sources to these female 15-pin HD
connectors (shown below). These connectors feature EDID
emulation.
3
2
1
13
14
8
A
1
U
D
I
O
I
N
P
U
T
3
LR
LR5LR7LR9LR
2
LR4LR6LR8LR10LR
15
MBD 249
2U Rack Mounting
Bracket (Pre-attached)
RS232
A
U
D
I
O
O
U
T
P
U
T
LAN
9
AMPLIFIED
LR
VARIABLE
LR
FIXED
LR
RESET
1314
10
11
12
NOTE: (Optional) To obtain one or two more RGB/YUV inputs, you can connect an Extron DVIIM-VGAF/DVIIF
DVI and Analog Breakaway (Y) cable to either or both DVI-I input connectors. Each Y cable provides an
additional RGB VGA connector and DVI-I connector (see ”Breakaway cable” on the next page).
1
DVS 510 Series • Setup Guide (Continued)
DVI-I Input Connector
Connector
z Video inputs 7/8 and 9/10 — Connect two DVI video sources, two RGB/YUV sources, or one DVI and one RGB
source to these DVI-I connectors. The analog portions of these connectors are identified as inputs 7 and 9, while the
DVI portions are inputs 8 and 10. These connectors feature EDID emulation.
1
9
17
Digital (Inputs 8 and 10)
8
24
C1
C5
C3
Analog (Inputs 7 and 9)
C2
C4
DVI-I Male Connector
Breakaway cable: You can use an optional Extron
DVIIM-VGAF/DVIIF “Y” DVI adapter cable (shown at
right) to connect one analog RGB or YUV source and
one DVI source to one or both of these connectors.
This cable enables both an analog and a DVI source
To DVS 510 Female DVI-I
Input Connector (Inputs 7 – 10)
device to be connected to these ports and active at
the same time.
4. Connect audio input devices to the Audio Input captive screw connectors (
previous page), as shown below.
Tip
Ring
Sleeve (s)
Tip
Ring
Balanced Stereo Input
and
f
) and Fixed (k) Audio Output captive screw connectors.
j
LR
Do not tin the wires!
g in the diagram
Do not tin the wires!
Tip
Sleeve
Tip
Sleeve
Unbalanced Stereo Input
LR
5. Connect video output devices to the Video Output connectors (
6. Connect audio output devices to the 5-pole Variable (
Tip
Ring
Sleeve
Tip
Ring
Balanced Audio Output
LR
NO Ground Here
NO Ground Here
Tip
Sleeve
Tip
Unbalanced Audio Output
Female DVI-I Connector
FOR DIGITAL ONLY
Female 15-pin HD Connector
FOR ANALOG ONLY
Extron
on the rear panel diagram on the
h
LR
).
Speaker 1
To a DVI
Input Source
To an RGB or
YUV Analog
Input Source
Speaker 2
CAUTION: For unbalanced audio, connect the sleeves to ground.
DO NOT connect the sleeves to negative (–) contacts.
DVS 510 SA: Connect speakers to the internal amplifier through the 4-pole
Amplified connector (i) (see also the illustration at right).
z Connect the red speaker wire to the positive (+) pin on the Amplified connector.
z Connect the black speaker wire to the negative (–) pin on the connector.
7. Connect control devices:
z LAN Ethernet port — Connect the DVS 510 to an Ethernet LAN or WAN via this RJ-45 connector (
DVS 510 SA
Rear Panel
n
the scaler from a remote location using an Internet browser on a computer.
z RS232 port — For serial RS-232 or RS-422 control, connect a host computer or control system to the DVS via this
9-pin D-sub connector (o).
z The front panel has an additional serial port (RS-232 only) (see “Front Panel Features” on the next page).
The default protocol for both ports is 9600 baud, 1 stop bit, no parity, 8 data bits, and no flow control.
8. Connect power to the DVS 510 by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz
power source into the power receptacle (a).
Locking the Front Panel (Executive Mode)
To prevent accidental changes to settings, you can lock the DVS 510 front panel controls by placing the scaler in lock
(executive) mode 1 or 2. While the DVS is in lock mode, RS-232 or RS-422 and IR remote control remain available.
z Lock mode 1 locks all front panel functions. This mode can be enabled or disabled only by SIS commands.
z Lock mode 2 locks all front panel functions except input selection, PIP, volume control, and Auto-Image™. To enable
lock mode 2, press and hold the Position and Size buttons simultaneously until Executive Mode 2 Enabled appears in
the LCD window (approximately 2 seconds).
To exit lock mode 2, press and hold the Position and Size buttons again until Executive Mode Disabled appears in
the LCD window (approximately 2 seconds).
2
Audio Output
to Speakers
4-pole Captive
Screw
AMPLIFIED
Ohms
LR
) to control
4/8
Loading...