IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP T UWP 4K D Series • Setup Guide
V
Projector
Signal Output
Cable
Cable
Clamp
Decora Faceplate
Extron
DTP HWP 232 D
Screws or
Nails
Wall opening is
flush with edge of box.
Wall Stud
AUTO SW
CONFIG
HDCP
1
IR OUT
HDMI IN
AUDIO IN
S
G
AUDIO IN
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP T UWP 4K D series of
Twisted Pair (TP) wallplate extenders.
1 2 3 4 5 6 7 8
CONFIG
E
1
3
CONFIGURABLE
100-240V ~ -- A MAX
2
4
50/60 Hz
IN1608
INPUTS
INPUTS
5
HDMI
6
SIGNAL
HDCP
IN1608 SA
OVER DTP
RS-232 IR
C
TxRx TxRxG
7
8
SIG LINK
SIG LINK
SIG LINK
OVER DTP
OVER DTP
HDMI
RS-232 IR
RS-232 IR
DTP OUT
TxRx TxRxG
DTP IN
DTP IN
TxRx TxRxG
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Step 2 — Prepare the Mounting Surface
AUTO SW
AUDIO IN
AUDIO IN
HDCP
1
VGA IN
HDMI IN
CONFIG
Extron
DTP T UWP 4K 232 D
Transmitter
XTP DTP 24 Cable
230'
INPUTS
1
2 3 4 5 6 7 8 A B C
OUTPUTS
A
HDMI
B
OUTPUTS
MENU
VOLUME
ENTER
IN1608
SCALING PRESENTATION SWITCHER
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L3R
AUDIO INPUTS
OUTPUTS
LL1R R
L5R
12
CLASS 2 WIRING
REMOTE
LAN
+48V
MIC/LINE
VARIABLE
RESET
L2
L4
R
R
RS-232
L6
LR
R
2
+48V
TxRx
DTP HDMI 4K 230 Rx
IPCP 505
COM
SWITCHED
12VDC
LIMIT
2
R
G
314
TXRXTX
OVER
12345678
IPCP 505
SIG LINK
POWER
12V
0.7A MAX
DTP IN
Wall opening is
flush with edge of box.
RTS
IR/S
CTS
4
RX
5162738
Ethernet
OUTPUTS
Wall Stud
Screws or
Nails
RELAY
5162314
LR
FLEX
100
eBUS
I/O
ACT LIMIT
2
4
OVER
738
Network
LINK
IR
ACT
TLP 1000T
AUDIO
HDMI
ATTENTION:
• Installation and service must be performed by
authorized personnel.
• L’installation et l’entretien doivent être effectués
par le personnel autorisé uniquement.
• The unit must be installed in accordance with the
Cable
Clamp
AUDIO IN
AUTO SW
HDCP
1
VGA IN
AUDIO IN
CONFIG
HDMI IN
National Electrical Code and with local electrical
and safety codes.
Signal Output
Cable
Extron
DTP UWP 4K 232 D
• L’unité doit être installée conformément au
National Electric Code et aux normes électriques
et de sécurité locales.
NOTE: Use a wall box with a depth of at least 3.0 inches (7.6 cm). Alternatively, the included mud ring (MR 200) can be
used. For more information, see the DTP T UWP 4K D Series User Guide at www.extron.com.
a. Place the wall box against the installation surface and mark the opening guidelines.
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Secure the wall box to the wall stud with 10-penny nails or #8 or #10 screws, leaving the front edge ush with the
surface.
d. Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.
Decora Faceplate
TIP: In order to t the unit in the junction box, do not install boots on TP cables and RJ-45 connectors.
DTP T UWP 4K D • Setup Guide (Continued)
Front Panel
A
B
R
DTP OUTREMOTEOVER
DTP
SIG LINK
RS-232
CONTACT
DTP T UWP 232 D
Tx Rx
Tx Rx G
POWER
12V
A MAX
0.9
+–
G12
A/S
Rear Panel
DTP T UWP 232 D
Rear Panel
F
A
B
C
D
E
Connected RS-232 and
l
l
SIG LINK
DTP IN
Step 3 — Connect Inputs to the Transmitter
Front Panel
A Audio input connector — Connect an unbalanced stereo
audio source to this 3.5 mm mini stereo jack.
B HDMI input connector — Connect an HDMI cable between
this port and the output port of the digital video source.
C VGA input connector — Connect a VGA cable between this
port and the output port of the video source.
D Mini USB port — Connect a male Mini USB-B cable to this
port for SIS conguration and rmware updates.
Rear Panel
A DC power input connector — Wire and plug the included external
12 VDC power supply into either this 2-pole connector or the power
input connector on the receiver (see the DTP T UWP 4K D Series User
Guide at www.extron.com for wiring information).
B Over DTP connector — Connect an RS-232 device to this 3-pole,
3.5 mm captive screw connector for pass-through RS-232 control.
C Remote connector — Connect an RS-232 device, contact closure
device, or both to this 5-pole, 3.5 mm captive screw connector to
control switching on the unit. Wire the connector as shown in the
diagram below.
• RS-232 — To control the unit through this port, connect an RS-232
device and congure it as follows: 9600 baud rate, 8 data bits,
1 stop bit, no parity.
• Contact — Momentarily short pins 1 or 2 to ground (G) to select
the corresponding input.
D Grounding Screw — Connect a grounding wire from this screw to the
wall box to ground the unit.
E DTP OUT connector — Connect one end of a twisted pair cable to this
RJ-45 connector and the opposite end to a compatible receiver.
Tx/Rx
Pins
RS-232 Contact
Contact Closure Device Pins
21
G
RxTx
Pin 2 for contact closure contro
Pin 1 for contact closure contro
Ground
Transmit pin on connected unit
Receive pin on connected unit
SIG LINK
DTP OUT
AUTO SW
AUDIO IN
HDMI IN
E
DTP T UWP 4K D
Reset
HDCP
1
CONFIG
AUDIO IN
VGA IN
+–
Tx Rx G
0.9 A MAX
Tx Rx
G12
12V
DTP
RS-232
CONTACT
SIGLINK
DTP T UWP 4K D
A DC power input connector
B Over DTP connector
C Remote connector
D Grounding screw
E DTP OUT connector
F Reset button (page 3)
A
C
D
POWER
A
DTP T UWP 4K 232 D
B
C
DTP OUTREMOTEOVER
D
E
2
ATTENTION:
• Do not connect these outputs to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de
télécommunications.
NOTES:
• The DTP T UWP 4K 232 D model can transmit video, control, and audio (if applicable)
signals up to 230 feet (70 meters).
• The DTP T UWP 4K 332 D model can transmit video, control, and audio (if applicable)
F Reset button — To perform a factory reset, use an Extron Tweeker or small screwdriver to press and hold this recessed
button for 6 seconds while the switcher is running.
signals up to 330 feet (100 meters).
DTP T UWP 4K D • Setup Guide (Continued)
TP Wires
Pins:
Step 4 — Run Cables Between Units
Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
z RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B wiring
standard for all connections.
For more information on TP cable wiring and termination, see the full product user guide.
z Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the device with
DTP transmitters or receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
z Use shielded RJ-45 plugs to terminate the cable.
z Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches
used. If possible, limit the number of patches to two total.
z If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 5 — Connect the Outputs from a Compatible Receiver
12345678
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
TIA/EIA
T568-B
a. Connect a DVI or HDMI cable (depending on your receiver type) between the receiver output port and the input port of
the display.
b. Connect a stereo audio device to the 3.5 mm mini stereo jack to receive the passed-through unbalanced audio.
c. Connect an RS-232 and contact closure device to the rear RS-232/Contact port (see the DTP T UWP 4K D Series
User Guide for wiring details).
Step 6 — Power the Units
The units can be powered one of two ways:
z Locally with the included power supply. A compatible receiver can then be powered remotely through the DTP line.
z Remotely via the DTP line by a locally powered DTP 230 or 330 compatible device.
NOTE: See the DTP T UWP 4K D Series User Guide for wiring information.
Step 7 — Final Installation
a. Make all connections, power the units, and test the system for satisfactory operation.
b. At the power outlet, unplug the power supply.
c. Mount the transmitter into the wall box, and attach the supplied decorator-style faceplate to the unit.
d. At the power outlet, reconnect the power supply. This powers up both units.
3
Operation
Front Panel
NOTES:
• Input switching can be performed only via auto switch, RS-232, or contact closure through the rear panel connectors.
• Auto switching can be activated or deactivated only via SIS commands. The default is ON with highest input as priority.
After all devices are powered up, the system is fully operational.
Transmitter LEDs
A Power LEDs — These two-color front panel LEDs on the transmitters light to
indicate signal and
power status as follows:
Amber — The unit is receiving power but there is no signal on the HDMI
or VGA inputs.
Green — The unit is receiving power and a signal is present on the HDMI
or VGA inputs.
B Auto Switch LED — Lights green when auto switch is active (see Rear Panel
on page 2).
C
A
B
C
AUDIO IN
HDMI IN
E
AUTO SW
HDCP
CONFIG
1
C HDCP LED — Lights green when HDMI input has been authenticated on the
source device.
Audio Configuration
The DTP T UWP 4K D series of products can embed analog audio inputs onto the digital video output. Use Extron PCS software
(available at www.extron.com) or SIS commands (see the DTP T UWP 4K D Series User Guide) to select the desired embedded
audio mode.
DTP T UWP 4K D
AUDIO IN
VGA IN
NOTE: If no VGA or HDMI signal is present, analog audio will be transported over the DTP connection to the analog audio
output of the receiver.
When an input is selected, audio transport over HDMI can be congured to operate in one of three modes. Each input can be
congured individually for any of the three modes.
z Transport embedded digital audio (default) — The embedded digital audio content on the digital video input is transported.
Analog audio is still separate from the digital embedded audio on the HDMI signal and transported simultaneously over the
DTP output, not embedded onto the digital output.
z Embed analog audio input — The analog audio input is always embedded to the digital output, replacing whatever content
is already present on the embedded digital audio. Analog audio is also transported over the DTP output as a simultaneous
output.
z Auto select between analog audio and digital audio — When both analog audio and digital embedded audio on HDMI are
present, embedded digital audio on the HDMI signal takes priority. Analog audio is transported simultaneously with the digital
embedded audio content that is already present on the DTP output.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
68-3157-50 Rev. A
10 17
Loading...