Extron DTP T UWP 232, DTP T UWP 332 D, DTP T HWP 232, DTP T HWP 332 D User Manual
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP T HWP/UWP D 232/332 D • Setup Guide
Decora Faceplate
W
flush with edge of box.
This setup guide provides instructions for an experienced installer to set up and operate the
Extron DTP T HWP D and DTP T UWP D family of wallplate extenders.
OUTPUTS
8
SIG LINK
RS-232 IR
TxRx TxRxG
DTP IN
OVER DTP
SIGNAL
1
HDCP
IN1608 SA
OUTPUTS
C
SIG LINK
DTP OUT
2 3 4 5 6 7 8 A B C
A
B
INPUTS
MENU
ENTER
AUDIO INPUTS
LL1R R
L5R
+48V
HDMI
MIC/LINE
L2
L4
L6
R
R
R
2
+48V
XTP DTP 24 Cable
230 '
VOLUME
IN1608
SCALING PRESENTATION SWITCHER
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L3R
OUTPUTS
12
CLASS 2 WIRING
REMOTE
LAN
VARIABLE
RESET
RS-232
LR
TxRx
G
IPCP 505
SWITCHED
12VDC
LIMIT
2
R
TXRXTX
1 2345678
314
OVER
IPCP 505
SIG LINK
POWER
12V
0.7A MAX
DTP IN
DTP HDMI 230 Rx
COM
RTS
FLEX
IR/S
RELAY
I/O
CTS
4
2
4
RX
5162738
5162314
738
OUTPUTS
AUDIO
LR
HDMI
AUTO SW
AUDIO IN
AUDIO IN
HDCP
1
VGA IN
HDMI IN
CONFIG
IR OUT
G
S
Extron
DTP T UWP 232 D Tx
Transmitte r
AUTO SW
AUDIO IN
AUDIO IN
HDCP
HDCP
1
1
2
HDMI IN
HDMI IN
CONFIG
IR OUT
G
S
Extron
DTP T HWP 232 D Tx
Transmitte r
INPUTS
1 2 3 4 5 6 7 8
CONFIG
Extron
INPUTS
OVER DTP
100-240V ~ -- A MAX
50/60 Hz
IN1608
1
3
CONFIGURABLE
2
4
RS-232 IR
5
TxRx Tx RxG
7
SIG LINK
OVER DTP
HDMI
HDMI
RS-232 IR
6
DTP IN
TxRx TxRxG
XTP DTP 24 Cable
230 '
XTP DTP 24 Cable
230 '
A Typical DTP T HWP 232 D and DTP T UWP 232 D Application
eBUS
ACT LIMIT
OVER
100
LINK
IR
ACT
Projector
Ethernet
Network
TLP 1000TV
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Step 2 — Prepare the Mounting Surface
ATTENTION:
• Installation and service must be performed by authorized
personnel only.
• The installation shall be in accordance with applicable
provisions of the National Electrical Code and any local
electrical codes.
NOTE: Use a wall box with a depth of at least 3.0 inches
(7.6 cm). Alternatively, the included mud ring (MR 200)
can be used. For more information, see the full product
user guide at www.extron.com.
a. Place the wall box against the installation surface and mark the
opening guidelines.
TIP: Use a level to mark the opening.
all opening is
Cable
Clamp
Wall Stud
Screws or
Nails
Signal Output
Cable
AUDIO IN
AUTO SW
HDCP
1
VGA IN
AUDIO IN
CONFIG
HDMI IN
IR OUT
G
S
Extron
DTP T UWP 232/332 D
b. Cut out the material from the marked area.
c. Secure the wall box to the wall stud with 10-penny nails or #8 or #10 screws, leaving the front edge ush with the
surface.
d. Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.
TIP: In order to t the unit in the junction box, do not
install boots on TP cables and RJ-45 connectors.
DTP T HWP/UWP 232/332 D • Setup Guide (Continued)
AA
R
DTP OUTREMOTEOVER
DTP
SIG LINK
RS-232
CONTACT
DTP T UWP 232 D
Tx Rx
Tx Rx G
POWER
12V
A MAX
0.9
+–
G12
A/S
Rear Panel
DTP T UWP 232 D
Rear Panel
1
2
5
6
3
E
Connected RS-232 and
l
l
RS-232 Contact
d
S
AUTO SW
A
B
D
IR OUT
AUDIO IN
HDMI IN
S
G
HDCP
CONFIG
AUDIO IN
1
HDMI IN
2
Extron
DTP T HWP 232/332 D
Front Panel
Step 3 — Connect Inputs to the Transmitter
Front Panel
A Audio input connector — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack.
NOTE: The units do NOT embed analog audio onto the HDMI signal. This analog audio signal is
transmitted simultaneously with audio embedded within the HDMI signal.
B HDMI input connector — Connect an HDMI cable between this port and the output port of the digital video source.
C VGA input connector — Connect a VGA cable between this port and the output port of the video source.
D IR output connector — Connect an IR device to this 2-pole, 3.5 mm captive screw pass-through connector for IR
control. Wire the cable as shown in the illustration to the right.
E Mini USB port — Connect a male Mini USB B cable to this port for SIS conguration and
rmware updates.
Rear Panel
A DC power input connector — Wire and plug the included external
12 VDC power supply into either this 2-pole connector or the power
input connector on the receiver.
ATTENTION: See Step 6 on the following page before wiring or
connecting the power supply.
B Over DTP connector — Connect an RS-232 device to this 3-pole,
3.5 mm captive screw connector for pass-through RS-232 control.
C Remote connector — Connect an RS-232 device, contact closure
device, or both to this 5-pole, 3.5 mm captive screw connector to
control switching on the unit. Wire the connector as shown in the
diagram to the right.
• RS-232 — To control the unit through this port, connect an RS-232
device and congure it as follows: 9600 baud rate, 8 data bits,
1 stop bit, no parity.
• Contact — Momentarily short pins 1 or 2 to ground (G) to select
the corresponding input. Connect pins 1 and 2 to ground (G) to
set the unit to auto switch mode. The device selects the highest
active input (auto switch).
A
B
E
B
D
IR OUT
AUDIO IN
HDMI IN
S
G
AUTO SW
HDCP
CONFIG
AUDIO IN
1
VGA IN
C
E
Extron
DTP T UWP 232/332 D
Front Panel
Signal
G
0.9
POWER
12V
+–
A MAX
Tx Rx G
R
DTP
RS-232
Tx Rx
CONTACT
G12
A/S
SIG LINK
DTP OUTREMOTEOVER
Groun
3/16”
(5 mm) Max.
A
B
C
D
Tx/Rx
Pins
DTP T HWP/UWP 232/332 D
Contact Closure Device Pins
21
G
RxTx
Pin 2 for contact closure contro
Pin 1 for contact closure contro
Ground
Transmit pin on connected unit
Receive pin on connected unit
2
Loading...