Extron DTP HDMI 230 Setup Guide
IMPORTANT:
IMPORTANT:
DTP HDMI 230 Tx Rear Panel
DTP HDMI 230 Rx Rear Panel
Front Panel
DTP HDMI 230 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
AUDIO
INPUTS OVER DTP
RS-232
IR
Tx Rx Tx RxG
POWER
12V
0.7A MAX
SIG LINK
DTP OUT
3 6
3
7 71 54 42
TP Wires
Pins:
e pin on connected unit
ansmit pin on connected unit
Connected RS-232
e pin on connected unit
ansmit pin on connected unit
RS-232
IR
LR
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
DTP HDMI 230 • Setup Guide
product to the power source.
This guide provides quick start instructions for an experienced installer to set up and operate the Extron DTP HDMI 230 digital video
extender. The DTP HDMI 230 transmitter and receiver pair can extend an HDCP-compliant HDMI signal up to 230 feet (70 m).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
Step 2 — Connections
HDMI Input connector (Tx) — Connect an HDMI cable
a
between this port and the HDMI output port of the digital
video source.
NOTE: See the “LockIt™ Lacing Brackets“ on the back of this guide for to
securely fasten the input HDMI connector to the transmitter.
Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini
b
stereo jack for an analog audio input.
RS-232 and IR connectors — To pass serial or infrared data or control signals, such as
c
serial control of a projector, connect the primary device to the transmitter and the secondary
device to the receiver via the RS-232 and IR captive screw connectors on both units.
DTP RJ-45 connectors — Connect transmitter DTP Out to receiver DTP In.
d
Extron recommends that you terminate both cable ends in accordance with the following
specifications, at a minimum:
• TIA/EIA T 568 B • CAT 6A, shielded •24 AWG, solid conductor
ATTENTION:
• Do not connect these devices to a computer data or telecommunications network.
• Ne connectez pas ces appareils à un réseau de télécommunications ou de données
informatiques..
Signal LED — Lights when the unit is receiving a TMDS clock signal on the HDMI input (transmitter) or
any valid signal on the DTP In connector (receiver).
Link LED — Lights when a valid link is established between the units on the DTP cable.
HDMI Output connector (Rx) — Connect a display with an HDMI input for display of the
e
transmitted direct digital image.
NOTE: See the “LockIt™ Lacing Brackets“on the back of this guide for to securely fasten
the output HDMI connector to the receiver.
INPUTS
AUDIO
Tx/Rx
Pins
Tx Rx Tx RxG
and IR Device Pins
Tr
Receiv
Ground
Tr
Receiv
12345678
TIA/EIA T568B
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
OUTPUTS
AUDIO
1
68-2244-
50 Rev. B
10 20
Audio Output connector (Rx) — Connect a balanced or
Unbalanced Stereo Output Balanced Stereo Output
Do not tin the wires!
No Ground Here
Rear Panel
ear Pane
l
Front Panel
ront Pane
l
POWER
12V
0.6 A MAX
21
Smooth
.
f
unbalanced stereo or mono audio device to the receiver via the
Audio captive screw connector. See the drawing below.
Tip
LR
Tip
Sleeves
Tip
No Ground Here
Power connector — Connect an IEC power cord between the included 12 VDC
g
power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply
Ring
Sleeves
Ring
Tip
LR
to either unit as shown at right. Use the included tie-wrap to strap the cord to the
captive screw connector.
NOTE: Only one power supply is required. A single power supply
connected to either unit in the pair powers both units. A power supply is
included with each transmitter.
Operation
After all devices are powered up, the system is fully operational. See the denitions
of the power indications (shown at right), below:
Power LED (front panel) —
a
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is powered on and is receiving an active HDMI signal, either on the
HDMI input if a transmitter, or transmitted on the DTP cable if a receiver.
ATTENTION:
• Connect the sleeves to the ground contact. DO NOT
connect the sleeves to the negative (-) contacts.
• Raccordez les manchons à la masse (GND). Ne PAS
connecter les manchons aux contacts négatifs (–).
Ridges
SECTION A–A
Power Supply
Output Cord
AA
Captive
Screw
Connector
3"
16 (5 mm) Max
Power LED (rear panel) —
b
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3
Sales and Technical Support Hotline that is closest to you, at the number shown below.
LockIt™ Lacing Brackets
1. Use an included LockIt Lacing Bracket to securely fasten an HDMI cable to each device as
follows.
2. Plug the HDMI cable into the panel connection (a).
3. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing
bracket to be placed over it (b). The screw does not have to be removed.
4. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the
screw to secure the bracket (c).
ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield it fastens
to is very thin and can easily be stripped.
5. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as
shown (
6. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any
excess length (e).
d
).
3
1
3
4
5
2
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
2
© 2012-2020 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Loading...