How it Works
Extron
Loading...
DTP DVI 330
Setup Guide
2 pgs660.42 Kb0

Extron DTP DVI 330 Setup Guide

IMPORTANT:
IMPORTANT:
DTP DVI 330 Tx
TP Wires
Pins:
e pin on connected unit
ansmit pin on connected unit
Connected RS-232
e pin on connected unit
ansmit pin on connected unit
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
DTP DVI 330 • Setup Guide
product to the power source.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
INPUTS
AUDIO
Front Rear
DVI-D
1 523
LOCAL OUTPUT
DTP DVI 330 Tx
DTP DVI 330 Rx
OUTPUTS
DVI-D
Front Rear
6 5
AUDIO
L R
DTP DVI 330 Rx
Step 2 — Connections
DVI Input connector (Tx) — Connect an DVI cable between this port and the DVI output port of the digital video source.
a
Local Output connector (Tx) — If desired, connect a DVI monitor for local monitoring of the input digital image.
b
Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
c
RS-232 and IR connectors (both units) — To pass serial or infrared data or control signals,
d
such as serial control of a projector, connect the primary device to the transmitter and the secondary device to the receiver via the RS-232 and IR captive screw connectors on both units.
DTP RJ-45 connectors (both units) — Connect transmitter DTP Out to receiver DTP In.
e
Extron recommends that you terminate both cable ends in accordance with the following specifications, at a minimum:
• TIA/EIA T 568 B • CAT 6A, shielded •24 AWG, solid conductor
ATTENTION:
• Do not connect these devices to a computer data or telecommunications network.
DVI Output connector (Rx) — Connect a display with an DVI input for display of the transmitted direct digital image.
f
Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio
g
• Ne connectez pas ces appareils à un réseau de télécommunications ou de données
informatiques..
Sig(nal) LED (both units) — Lights when the unit is receiving a TMDS clock signal on the DVI input (transmitter) or any valid signal on the DTP In connector (receiver).
Link LED (both units) — Lights when a valid link is established between the units on the DTP cable.
captive screw connector. See the
drawing on page 2.
POWER 12V
0.8 A MAX
POWER 12V
0.8 A MAX
8
8
DDC ROUTE
ON
SHARE
REMOTE
1 2
LOCAL
SIG LINK
SIG LINK
DTP IN
Tx/Rx
Pins
RxTx
Rx GTx
RS-232 IR
DTP OUT
and IR Device Pins
Tr Receiv
Ground Tr Receiv
12345678
OVER DTP
RS-232 IR
Rx GTx
4
OVER DTP
RS-232 IR
Rx GTx
47
TIA/EIA T
568 B
Pin
Wire color
White-orange
1
Orange
2
3
White-green
4
Blue
5
White-blue
Green
6
7
White-brown
8
Brown
RxTx
RxTx
1
68-2342-
50 Rev. B
11
20
Unbalanced Stereo Output Balanced Stereo Output
Do not tin the wires!
Tip
No Ground Here
LR
Rear (Tx)
LOCAL
SPARE
REMOTE
DDC ROUTE
POWER 12V
0.8 A MAX
1 2
ON
2 3
Smooth
.
LR
Tip
Sleeves
Tip
No Ground Here
Ring
Sleeves
Ring
Tip
ATTENTION:
• Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.
• Raccordez les manchons à la masse (GND). Ne PAS connecter les manchons aux contacts négatifs (–).
Power connector — Connect an IEC power cord between the included 12 VDC
h
power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to either unit as shown at right. Use the included tie-wrap to strap the cord to the captive screw connector.
NOTE: Only one power supply is required. A single power supply connected to
either unit in the pair powers both units. A power supply is included with each transmitter.
Operation
After all devices are powered up, the system is fully operational. See the denitions of the power indications (shown at right), below:
Power LED (front panel) —
a
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is powered on and is receiving an active DVI signal, either on the DVI
input if a transmitter, or transmitted on the DTP cable if a receiver.
SECTION A–A
Power Supply
Output Cord
Ridges
Captive
Screw
Connector
3" 16 (5 mm) Max
AA
Power LED (rear panel) —
b
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
c
DDC Route switch — This rear panel switch selects either the remote or local DVI display as the display data channel (DDC)
reference for EDID and HDCP communication.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.
LockIt™ Lacing Brackets
1. Use an included LockIt Lacing Bracket to securely fasten an DVI cable to each device as follows.
2. Plug the DVI cable into the panel connection (a).
3. Loosen the DVI connection mounting screw from the panel enough to allow the LockIt lacing
bracket to be placed over it (b). The screw does not have to be removed.
4. Place the LockIt lacing bracket on the screw and against the DVI connector, then tighten the screw
to secure the bracket (c).
ATTENTION: Do not overtighten the DVI connector mounting screw. The shield it fastens
to is very thin and can easily be stripped.
5. Loosely place the included tie wrap around the DVI connector and the LockIt lacing bracket as
shown (
6. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any
excess length (e).
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
2
).
d
© 2012-2020 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
3
2
1
3
4
5
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use