Extron DTP2 T 204 Setup Guide

DTP2T204 • Setup Guide

A

B

C

D

E

F

G

H

Extron

Pins:

IMPORTANT:

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

The Extron DTP2 T 204 is an HDCP-compliant, four
input HDMI switcher with a DTP2 output that switches
and extends digital embedded audio, bidirectional
RS-232, IR, and remote power.

It supports video resolutions up to 4K @ 60 Hz and
1080p @ 120 Hz, using shielded twisted pair cabling as
a transmission medium, and extends HDMI video signals

DTP2 R 211

Receiver

SIG LINK

OVER DTP2

DTP2 IN

OUTPUTS

AUDIO

L

R

ON/OFF/MUTE Control

ON OFFMUTE

Extron
CCR 30

Contact Closure Remote
with Three LED Switches

RS-232

HDMI

POWER
12V

--A MAX

RS-232 IR

TxRx TxRxG

MODEL 80

up to 330 feet (100 meters).

CATx Cable

The switcher features four HDMI inputs and a
DTP2/HDBT output, data rates up to 18 Gbps, HDR,
12 bit Deep Color, 3D, Lip Sync, HD lossless audio
formats, and SIS to CEC control. EDID Minder®
maintains EDID communication with connected devices
and ensures that the HDMI sources power up properly
and maintain correct video output.

Control is available via front panel buttons, USB, Extron
Product Control Software (PCS), Ethernet, RS-232,

Extron
DTP2 T 204

Transmitter

Extron
HDMI SM

Show Me Cables

up to 330' (100 m)

DTP2 T 204

POWER

1234

12V

2.0AMAX

SHARE

SHARE

OVER TP

HDBT

SEND POWER

RS-232 IR

56

TxRx GTxRx

OFF

DTP

C

C

TG+V

CONT

12 34

C

C

TG+V

Ethernet

REMOTE

RS-232

Tx

Rx

G

TTCCT+VT

LAN

POWER
12V

0.3A MAX

Tx Rx RTSCTS

LAN

COM 1 COM 2 COM 3

G

Tx Rx RTSCTS

G

Tx Rx RTSCTS

IPL PRO S3

G

LAN / PoE

INPUTS

SHARE

LINKSIG

OUT

HDMI

contact closure, and auto-input switching for integration
with any control system. Front panel LED indicators provide immediate visual conrmation of HDCP authentication and signal
presence for each input and output. Remote power for the end unit is available via the DTP output.

This guide provides instructions for an experienced installer to set up and operate this switcher. For full installation,
conguration, and operation details, see the DTPT204 User Guide, available at www.extron.com.

Rear Panel Features and Connections

FLAT PANEL

Flat Panel Display

Extron
IPL Pro S3

IP Link Pro
Control Processor

Ethernet

LAN

DTP2 T 204

POWER

1 2 3 4

12V

2.2A MAX

Figure 1.

Installation Steps

1. Turn off and disconnect all of the equipment from the power source.

2. Mount the switcher on a rack shelf or furniture (optional).

3. Connect HDMI input sources to one or more of the DTP2T 204 inputs (see figure1,

present at each input and HotPlugDetect (HPD) is actively controlled on each input.

NOTES:

• The default (Extron) EDID is 1080p @ 60 Hz (see the DTP2T204 User Guide for the

4. Connect the input of a DTP2 or HDBaseT compatible device to the DTP/HDBT OUT

• LockIt® cable lacing brackets are provided to secure the HDMI cables to the rear panel

RJ-45 connector (C). See the image at right to wire the connector.

F

56

C

C

TG+V

REMOTE

RS-232

Tx

Rx

G

TTCCT +VT

TG+V

A
B
C
D

LAN

E

INPUTS

OUT

I

OVER TP

HDBT

Tx Rx GTxRx

DTP

LINKSIG

RS-232 IR

CONT

12 34

C

SEND POWER

OFF

C

F

DTP2T204Rear Panel

G
H
I

B

EDID table).

connectors to reduce stress on the HDMI connectors and prevent signal loss due to
loose cable connections (see the LockIt Lacing Brackets on page4).

Power input connector

HDMI input connectors

DTP/HDBT Output RJ-45 port

TP mode switch

Over TP RS-232 and IR port

Contact input and tally output
ports with +V connectors

Remote RS-232 port

LAN RJ-45 port

Remote power toggle switch

). The default (Extron) EDID is

12345678

TP Wires

TIA/EIA T

Pin

Wire color

White-orange

1

Orange

2

3

White-green

4

Blue

White-blue

5

6

Green

7

White-brown

8

Brown

568 B

1

Connected RS-232
and IR Device Pins

RS-232

IR

Tx/Rx

m

C+

DTP2 T 204 • Setup Guide (Continued)

5. Set the TP mode switch (

• If the receiving device is an Extron DTP device, set the switch to DTP.

• If the receiving device is HDBaseT enabled, set the switch to HDBT.

) to HDBT (up) or DTP (down) as follows:

D

When the output is congured for DTP mode, remote power is available. When the output is congured for HDBT mode,
remote power is disabled and the switcher and receiver each require its own 12 VDC power supply.

ATTENTION:

• Position this switch before connecting the appropriate device to the TP connector. Failure to comply can damage

the endpoint.

• Positionnez le sélecteur avant de connecter l’appareil approprié au connecteur TP. Ne pas respecter cette

procédure pourrait endommager le point de connexion.

• Do not connect these devices to a computer data or telecommunications network.

• Ne connectez pas cet appareil à un réseau de télécommunications ou de données informatiques.

6. Connect Over TP RS-232 and IR control. Connect a serial RS-232 signal,

a modulated IR signal, or both into this 3.5 mm, 5-pole captive screw connector
(see figure1,E, on the previous page) for bidirectional RS-232 and IR
communication (see the image on the right to wire the RS-232 and IR connector).

7. Connect control devices. Connect your computer to one of the following

DTP2T204 communication ports to configure and control
the switcher via SIS commands or PCS:

• RS-232 port — Connect the unterminated transmit,

receive, and ground wires of the RS-232 cable to the

RS-232

Tx Rx G

DTP2 T 204 Switcher
Rear Panel
Remote Port

three pins on the provided 3-pole captive screw plug,
as shown in the image at right. Connect the plug to the
rear panel Remote RS-232 connector (G), and the

NOTE: If you use cable that has a drain
wire, tie the drain wire to ground at both ends.

other end of the cable to your computer serial port.
Protocol for the RS-232 port is 9600 baud, 8 data
bits, 1 stop bit, and no parity.

• Config port — Connect a USB mini-B cable to the

front panel USB connector (see figure2,B, on the
next page) for USB control.

• LAN port — To control the DTP2 T 204 through Ethernet, connect a LAN to the RJ-45 LAN connector (see figure 1,

). The default IP address of the scaler is 192.168.254.254, the default subnet mask is 255.255.255.0, and the default

H

gateway address is 0.0.0.0. (See the diagram in step 4 on the previous page to wire this connector.)

8. (Optional) Connect contact closure and tally indicator devices. The Contact/Tally

section of the rear panel (B, on the previous page) contains four captive screw
connectors, each containing two pairs of pins labeled C and T (see 1, 3, 5, and 6

in the image at right). Each C-T pin pair is labeled with its contact input number (1
through 6), and each individual pin is labeled with its function:

• C = Contact closure input

• T = Tally output

• G = Ground (for example, 4)

• +V = +V connector for the tally output power wire (for example, 2)

To enable input switching via contact closure, connect a contact closure device to a
contact-tally port as follows:

a. Connect a push-button contact closure device to a C pin of one of the contact-tally connectors.

b. Connect the ground wire of the contact device to one of the G pins.

c. If desired, to identify the currently selected input when the front panel LEDs are not visible, connect an indicator device,

such as an LED, to tally output pin (T) to the right of the connected C pin. When the input you are using is selected, the
corresponding tally out pin shorts to ground, which activates the connected indicator.

d. Insert the LED+ wire of the indicator device into a +V connector.

e. Press the button on the contact closure device to switch the connected input to the output.

2

Pins

Ground (G)
Receive (Rx)
Transmit (Tx)

Tx Rx Tx RxG

Transmit (Tx)
Receive (Rx)

POWER

SEND

111

22

OFF

333

CONT

12 34

C+VTCTCTCT

Transmit pin
Receive pin
Ground
Transmit pin
Receive pin

Computer or
Control Syste
RS-232 Port

555 666

5

G

REMOTE

RS-232

G

RxTx

444

6

VTGC+VT