Extron DTP2 User Manual
IMPORTANT:
4K HDR DisplayPC with 4K HD R Video O utput
DTP2 T 211 Rear Panel DTP2 R 211 Rear Panel
E D
AA B
B C
C DD A
A E
E H
HDDEE GGFF
Go to www.extron.com for the complete
user guide, installation instructions, and
DTP2T/R 211 • Setup Guide
specifications before connecting the
product to the power source.
The DTP2 T 211 transmitters and DTP2 R 211 receivers can extend HDMI digital video signal with resolutions up to 4K@60Hz
(4:4:4), analog and digital embedded audio, bidirectional RS‑232 and IR control, and remote power up to 330feet (100meters),
using shielded twisted pair cabling as a transmission medium. This guide provides quick start instructions for an experienced
installer to set up and operate the DTP2211 digital video extenders.
NOTE: Maximum transmission distances will vary with resolutions used, cable types, and environment (see the
DTP2T/R 211UserGuide at www.extron.com for full specifications).
Extron
DTP2 T 211
Transmitter
POWER
12V
--A MAX
STATUS
SEND
INPUT
POWER
LINK
CONFIG
OUTPUT
OFF
DTP2 T 211
INPUTS
AUDIO
SIG LINK
OVER DTP2
IR
RS-232
DTP2 OUT
TxRx Tx RxG
POWER
RS-232
HDMIAudio
12V
0.3A MAX
Tx Rx RTSCTS
CATx Cable up to 330' (100 m)
Figure 1. Typical Transmitter and Receiver Application
Installation
COM 1 COM 2 COM 3
G
Tx Rx RTSCTS
G
Tx Rx RTSCTS
G
IPL PRO S3
Extron
IPL Pro S 3
IP Link Pro
LAN / PoE
Control Processor
Extron
DTP2 R 211
Receiver
POWER
12V
--A MAX
RS-232
OVER DTP2
RS-323 IR
TxRx Tx RxG
STATUS
SEND
INPUT
POWER
LINK
CONFIG
OUTPUT
OFF
DTP2 R 211
SIG LINK
DTP2 IN
HDMI
OUTPUTS
AUDIO
L
R
Turn off and disconnect all equipment power sources and mount the transmitter and receiver units as required. The transmitter
and receiver can be securely mounted in a variety of locations, using optional Extron Mounting Brackets and accessories (see the
Extron website, to determine which optional mounting accessories are compatible).
Rear Panel Connections
POWER
12V
0.8A MAX
AUDIO
INPUTS
SIG LINK
DTP2 OUT
Figure 2. Rear Panels of the DTP2 T 211 and DTP2 R 211
Power inlet — Connect an IEC power cord between the included 12VDC, 1.5 A power supply and a 100‑240VAC, 50‑60Hz
A
source. Connect the power supply to either unit to power both units (see figure 3 on the next page to wire the power).
ATTENTION:
• Do not connect any external power supplies until you have read the Attention notications in the Power Supply
section of the DTP2 T/R 211 User Guide.
• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power
Supply » du DTP2 T/R 211 User Guide.
OVER DTP2
RS-232
Tx Rx Tx RxG
POWER
12V
IR
0.8A MAX
OVER DTP2
RS-232
Tx Rx Tx RxG
IR
SIG LINK
DTP2 IN
OUTPUTS
AUDIO
LR
1
DTP2T/R 211 • Setup Guide (Continued)
(5 mm) Max.
POWER
Connected RS-232
Balanced Audio Output
Slee
Unbalanced Audio Output
No Ground Here
TP Wires
Pins:
Tip (+)
3.5 mm Stereo Plug Connector
(unbalanced)
NOTE: One power supply is included with the transmitter and normally can power both units, if they are both from the
Extron DTP2 series.
A
Smooth
SECTION A–A
Ridges
3/16"
A
Figure 3. Power Wiring Diagram
Audio input (Tx) — Connect an unbalanced stereo audio source (see image on the right) to this
B
3.5mm mini stereo port (see
HDMI Input (Tx) — Connect an HDMI cable between this port and the HDMI output port of the digital video source.
C
figure 2 on the previous page) for an analog audio input.
12V
--A MAX
Ring (-)
Sleeve ( )
NOTE: See the LockIt™ Lacing Brackets on the next page to securely fasten the HDMI connectors.
DTP RJ‑45 ports — Connect transmitter DTP2 Out to receiver DTP2 In, using a Twisted
D
Pair Cable. Extron recommends terminating both cable ends in accordance with the wiring
specifications in the diagram on the right, at a minimum:
• TIA/EIA T 568 B • CAT 6A, shielded • 24 AWG, solid conductor
ATTENTION:
• Do not connect these devices to a telecommunications or computer data network.
• Ne connectez pas ces appareils à un réseau de télécommunications ou de données
informatiques.
RS‑232 and IR ports — To pass serial, infrared data, or control signals, connect the host device to the transmitter and the
E
periperal device to the receiver via the RS‑232 and IRcaptive screw connectors on both units (see figure 4 for wiring).
Tx/Rx
Pins
IR
RS‑232
Tx Rx Tx RxG
and IR Device Pins
Transmit pin
Receive pin
Ground
Transmit pin
Receive pin
12345678
Pin
1
2
3
4
5
6
7
8
TIA/EIA T
568 B
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Figure 4. RS‑232 Wiring Diagram
HDMI Output (Rx) — Connect a display with an HDMI input to display the transmitted digital image.
F
Audio Configuration Switch (Rx) — Set the Toggle switch to the UP position to de‑embed digital audio from the HDMI
G
signal and output it to the captive screw connector for analog audio output. Set the Toggle switch to the DOWN position for
the analog input from the TRS audio connector on the Tx unit to be transported simultaneously with the digital embedded
HDMI audio and output on the captive screw connector.
Audio Output (Rx) — Connect a balanced or unbalanced audio device, such as an audio amplifier or powered speakers, to
H
the receiver via the audio captive screw connector (see figure 5 to wire analog audio output).
Tip
Ring
ves
Tip
Ring
Figure 5. Balanced and Unbalanced Audio Output Wiring Diagram
ATTENTION:
• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–)
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux
NOTE: If the ground jumpers have been removed because of ground potential differences, the DTP2 T 211 transmitter
and DTP2 R 211 receiver cannot extend analog audio. No analog audio is output (see the DTP2T/R 211UserGuide at
www.extron.com for more information).
2
contacts.
contacts négatifs (–).
LR
Tip
Sleeves
Tip
No Ground Here
LR
Do not tin
the wires!
Loading...