AVTracTM Track Extension Kit
Floor-mount Raceway System
68-1492-01
Rev. C
09 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important operating and maintenance
(servicing) instructions in the literature provided with the equipment.
This symbol is intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s enclosure that may present a risk of electric shock.
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user
information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment
manufacturer because they may be hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel
contient des instructions importantes concernant l’exploitation et la maintenance
(réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil
de tensions dangereuses non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou
présentés dans la documentation utilisateur.
Eviter les pièces de xation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le
fabricant du matériel car cela risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dies es Symbol soll dem Benut zer in der im Liefer umfang ent haltenen
Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des
Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und
die einen elektrischen Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie
aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Warning
Power sources • This equipment should be operated only from the power source indicated on the product. This
equipment is intended to be used with a main power system with a grounded (neutral) conductor. The
third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of
the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall
plug).
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by
items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To
prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing
covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent
overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce
matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième
contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons
d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou
encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne
risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien
qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger
d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher
les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des
objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement
avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les
batteries usagees conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen)
Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel
aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der
Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand
darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks
versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr
eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empndlichen Teile im Inneren. Diese Öffnungen dürfen niemals von
anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte
Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller
empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes
de operación y mantenimiento (o cambio de partes) que se desean destacar en el
contenido de la documentación suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con
voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja
o alojamiento del producto, y que puedan representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el
equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente recomendados
por el fabricante, ya que podrian implicar riesgos.
安全须知 • 中文
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴露的危险电 压，有触电危险。
注意
阅读说明书 • 用户使用该设备前必须 阅读并理 解所有安 全和使 用说明。
保存说明书 • 用户应保存安全说明书以备将来使用。
遵守警告 • 用户应遵守产品和用户指南上 的所有安全和 操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备，以避免危险。
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución
general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica
al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el
módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde
no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calicado. En el interior no
hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente
la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a
voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el
sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta
batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las
baterías usadas siguiendo las instrucciones del fabricante.
警告
电源 • 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线（
地线）是安全设施，不能不用或跳过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后或桌面电源的电源线，或任何接到市电
系统的电源 线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不 要自己试图打开设备盖子 维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止机内敏感元件过热。 不要用任何东西
挡住通风孔。
锂电池 • 不正确的更换电池会有爆 炸的危险。必须使用与厂家推荐的相同或 相近型号的电池。按
照生产厂的建议处理废 弃电池 。
Kit Contents
Plastic Template (1)
Side Ramp (2)
Aluminum
Base Track (1)
Aluminum
Cover Track (1)
Installation
Guide
Double-Sided
Tape (1 roll)
5/32" Masonry Bit (1) and
3/16" Masonry Screws
The AVTrac™ Extension kit is available as a 4 feet (1.22 meter) extension for the AVTrac system. An optional rubber strip
inlay kit (part # 70-670-01) is available.
Check contents of each box to ensure all items are present.
N
Contents checklist
4 feet (1.22 m) Aluminum Base Track (1)
4 feet (1.22 m) Aluminum Cover Track (1)
4 feet (1.22 m) Side Ramps (2)
Plastic Wall Base Trim Template (1)
Double-sided Adhesive Tape (1 roll of 15 feet)
3/16 inches Masonry Screws (10)
5/32 inches Masonry Drill Bit (1)
Installation Guide (1)
If you are using the AVTrac extensions with the complete AVTrac system, please consult the AVTrac
Manual (#68-1405-01) or an Extron Representative for instructions and advice about compatibility.
AVTrac Extensions • Kit Contents
1
Before Getting Started
Tools and Equipment Required for Installation
Almost everything you need to install your AVTrac kit has been included. You will need some basic tools and materials
depending on the facility and requirements.
N
Extron recommends the following equipment (not provided) to ensure the AVTrac is properly installed:
Tools:
Equipment/Other:
All structural steps and electrical installation should be performed by qualified personnel in accordance with local and
national building codes and electrical codes.
Miter saw with blade for cutting metal
Hand saw for cutting drywall
Utility knives (box cutters)
Power drill
1/4 inches bit for drilling metal
Tin snips (metal shears)
Tools for terminating cables (if required)
Phillips head screw driver
Hex nut driver (1/4 inches and 5/16 inches)
Metal straightedge (for cutting carpet)
Tape measure
Marker pen
Level
Fish tape (used for pulling cables through cavity walls)
Cable ties
Vacuum cleaner
Carpet glue
Safety goggles
2
AVTrac Extensions • Before Getting Started
Installation
At this point you must already have checked the contents of the kit and gathered the tools that you will need for
installation.
Prior to installation, check to ensure that the Extension Kit matches the AVTrac product to make a proper junction.
Step 1: Track Mounting
W
For further information about using the AVTrac extensions with the complete AVTrac system, please consult the AVTrac
Installation Guide (part #68-1405-01) or the Extron Web site (www.extron.com) for instructions about installing the electrical
power and audio/video modules.
1-1 Whenever possible, completely remove the carpet
After removing the carpet, make sure that the
Determine whether the installation will be in new
New construction
When AVTrac is being placed in a new building, the
Prelaid Carpet
For installation of AVTrac under prelaid carpet, cut
Existing AVTrac rubber inlay models may be mismatched with the cover track of the extension kit. This
mismatch may present a tripping hazard. Consult an Extron representative for advice.
from where the track will be laid. If this is not
possible, cut the carpet.
concrete base is level and structurally sound. Prior
to installation, leveling and topping may be needed.
construction, under preexisting carpet tiles, or under
preexisting carpet rolls and follow the appropriate
instructions.
carpet should not be laid until the track has been
installed.
and/or peel back the carpet to expose the concrete
where the track and side ramps will be positioned
(as shown in figure to the right).
N
Remove carpet tiles to expose concrete.
AVTrac is not designed to be installed under vinyl composite tile (VCT).
AVTrac Extensions • Track Mounting
3
Installation
4" (10.2 cm)
1½" (3.8 cm)
1-2 If the AVTrac will abut the wall, remove the
baseboard from the bottom of the wall and mark the
position of the AVTrac.
1-3 Using a drill, box cutters, or a saw, cut a hole at the
base of the wall 4 inches W x 1½ inches H (10.2 cm x
3.8 cm).
If there is a metal base stud, use a hand saw or tin
snips to cut it at both edges of the hole and bend it
back into the hole so that it lies flat on the floor. Use
a file to remove any jagged edges that might damage
cables.
The hole will eventually be covered by the
baseboard, so it does not have to be perfect.
Step 1: Track Mounting, cont’d.
Mark wall.
4
Cut cable access hole in wall.
1-4 If necessary, measure and cut the track pieces to the
desired length. The cut must be clean, as it must
abut the existing AVTrac system or the wall.
Cut aluminum base track.
AVTrac Extensions • Track Mounting
1-5 Pre-drill mounting holes in the shallow grooves of
Shallow Groove
in Side Ramp
Pre-drill holes.
Shallow Groove
in Base Track
Pre-drill holes.
Side Ramp
Base Track
Drill 5/32” x 1-1/4” deep hole
into concrete.
Supplied Masonry Screws
Mate side ramp to base track.
Align extension kit
to installed AVTr ac.
the base track and side ramps using a 1/4 inches bit
for drilling metal (not supplied.)
N
Mounting holes must be a maximum of 3 feet (0.91
m) apart, and one must be within 6 inches (0.15 m) of
each end of the track.
1-6 If the extension kit is to be used with an existing
AVTrac installation, align the base track so that it
abuts the end of the installed AVTrac.
Mate the tabs in the side ramps with the grooves
in the base track.
Pre-drill holes in track and ramps.
W
Before using the Extension kit with an existing
AVTrac rubber inlay model, consult an Extron
representative for advice about compatibility.
1-7 Using the provided masonry bit, drill 1-1/4
inches deep pilot holes into the concrete through
the pre-drilled mounting holes in the track and
ramps.
1-8 With the provided masonry screws, secure the
track and ramps to the floor.
Align base track and mate side ramps.
Drill into concrete and screw down track.
Screw side ramps to floor.
AVTrac Extensions • Track Mounting
5
Installation
Carpet covers ramps
but not track.
At this point, the track must already have been secured to the floor.
To complete the installation of the AVTrac, follow these instructions:
2-1 Lay the cables and power cords flat against the base
track. If necessary, feed excess cable back into the
wall.
Snap the cover track onto the base track.
2-2 Before cutting and gluing the carpet, remove all dust
and debris with a vacuum cleaner.
Cut the carpet or carpet tiles so that they run up
to but do not cover the aluminum track (see the
diagram below).
Step 2: Finishing Up
Lay cables flat and fit cover track.
2-3 Glue or tape the carpet to the floor and side ramps.
Cut carpet.
Refit carpet.
6
AVTrac Extensions • Finishing Up
2-4 If the extension kit abuts the wall, use the provided
template to trim the wall base board so that it fits
snugly around the track.
2-5 Attach the base board to the wall.
Use template to cut base board.
Reattach base board to wall.
2-6 To insert a carpet inlay, cut a strip of the finished
carpeting and glue or tape it to the cover track
raceway.
For an alternative rubber finish, use the optional
rubber strip inlay kit (part # 70-670-01).
Attach carpet tile to track raceway.
AVTrac Extensions • Finishing Up
7
Reference Material
Specifications
Specifications
General
Mounting options .......................... Mountable on base flooring and beneath the finished carpet
Enclosure type ............................... Metal track base and top, plastic ramps
Enclosure dimensions: see diagrams opposite
Track system
Side ramps .......................... 0.67 inches (1.7 cm) H x 7.50 inches (19.0 cm) W on either side of track x 48 inches (121.9 cm) L,
approximately 4.5° slope
Track base and top ............ 0.95 inches (2.4 cm) H x 3.7 inches (9.4 cm) W x 48 inches (121.9 cm) L
Product weight .............................. 8.9 lbs (4.0 kg)
Shipping weight ............................ 11 lbs (5 kg)
Vibration ......................................... ISTA 1A in carton (International Safe Transit Association)
Compliances ................................... Title III, Regulation 28 CFR Part 36: ADA Standards for Accessible Design; Section 4.8: Ramps
Warranty ......................................... 3 years parts and labor
N
8
AVTrac Extensions • Reference Material
Specifications are subject to change without notice.
TOP VIEW
18.7"
(47.6 cm)
3.70"
(9.40 cm)
Aluminum
Tr ack Base
4’ 0” (121.9 cm)
Side Ramp
Aluminum
Track To p
4’ 0” (121.9 cm)
BACK VIEW
0.22"
(0.56 cm)
1.09"
(2.61 cm)
2.91"
(7.39 cm)
3.70"
(9.40 cm)
.67" (1.70 cm)
4.5°
7.50"
(19.05 cm)
7.50"
(19.05 cm)
AVTrac Extensions • Reference Material
9
Reference Material
Optional Accessories
AVTrac Floor System
Accessory Part Number
AVTrac 480C Carpet Inlay, No AC 42-121-00
AVTrac 480R Rubber Strip, No AC 42-122-00
AVTrac 480C AC Carpet Inlay, w/AC US, Prewired
Conduit
AVTrac 480R AC Rubber Strip, w/AC US, Prewired
Conduit
AVTrac 480C AC Carpet Inlay, w/AC EU, Isolated Cable 42-121-24D
AVTrac 480R AC Rubber Strip, w/AC EU, Isolated Cable 42-122-24D
AVTrac 480C AC Carpet Inlay, w/AC FR, Isolated Cable 42-121-24E
AVTrac 480R AC Rubber Strip, w/AC FR, Isolated Cable 42-122-24E
AVTrac 480C AC Carpet Inlay, w/AC AUS, Conduit Only 42-121-24F
AVTrac 480R AC Rubber Strip, w/AC AUS, Conduit Only 42-122-24F
AVTrac 480C UNIV ISO Carpet Inlay, w/AC Univ,
Isolated Cable
AVTrac 480R UNIV ISO Rubber Strip, w/AC Univ,
Isolated Cable
AVTrac 480C UNIV CO Carpet Inlay, w/AC Univ,
Conduit Only
AVTrac 480R UNIV CO Rubber Strip, w/AC Univ,
Conduit Only
AVTrac Rubber Inlay kit 70-670-01
AVTrac Rough-In Adapter 70-781-01
AVTrac Wall Trim Plate 70-782-01
AVTrac Raceway Transition (Wiremold) 70-783-01
AVTrac Raceway Transition (Euro Channel) 70-783-11
Accessories
42-121-24A
42-122-24A
42-121-24J
42-122-24J
42-121-00J
42-122-00J
10
To ensure a precise join when this kit is used with another AVTrac product, the two products must be compatible.
W
AVTrac Extensions • Reference Material
Before using the Extension kit with an older AVTrac rubber inlay model, consult an Extron representative.
All trademarks mentioned in this manual are the properties of their respective owners.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period
of three years from the date of purchase. In the event of malfunction during the warranty period
attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option,
repair or replace said products or components, to whatever extent it shall deem necessary to restore
said product to proper operating condition, provided that it is returned within the warranty period,
with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan: Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care,
electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification
to the product.
If it has been determined that the product is defective, please call Extron and ask for an Applications
Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.383.4400 (Asia), or 81.3.3511.7655 (Japan)
to receive an RA# (Return Authorization number). This will begin the repair process as quickly as
possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of
loss or damage during shipment. Returned units must include the serial number and a description of
the problem, as well as the name of the person to contact in case there are any questions.
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
Extron Electronics makes no further warranties either expressed or implied with respect to the
product and its quality, performance, merchantability, or fitness for any particular use. In no event
will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any
defect in this product even if Extron Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this
warranty may not apply to you.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714 .491.1500
+1.714 .491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FA X
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Quick Installation Checklist
Installation of AVTrac Extensions can be divided into three main sections:
Before Getting Started
Decide where the track will be installed and, if necessary, prepare the site.
Open the box containing the AVTrac kit and identify all the items provided (page 1).
Gather any additional tools needed for installation (page 2).
Step 1 — Installing Track
Remove existing carpeting (page 3).
If necessary, cut a hole in the drywall for the cables (page 4).
Measure and cut the track pieces (page 4).
Secure the base track to the floor (page 5).
Step 2 — Finishing Up
Snap on the cover track (page 6).
Cut the carpet and glue it to side ramps (page 6).
Trim the wall base boards and apply the finish to the cover track raceway (page 7).
AVTrac • Quick Installation Checklist
N
If you are using the AVTrac Extensions with the complete AVTrac system,
please consult the AVTrac Installation Guide (#68-1405-01) or the Extron
Web site (www.extron.com) for instructions about installing the electrical
power and audio-visual modules.
Loading...