Extreme tools RX723001HC, RX553001HC User Manual
Owner’s Manual
Professional Steel
Hutches
Models:
RX723001HC 72”W x 30”D
RX553001HC 55”W x 30”D
Extreme Tools, Inc.
740 Frontenac Rd.
Naperville, Illinois 60563
630.369.9303
www.ExtremeTools.net
sales@extremetools.net
72 inch Steel Top Hutch
shown on RX723016RC
22 7230HC-19 ADJUSTABLE SHELF 1
22 5530HC-19 ADJUSTABLE SHELF 1
23
55”W x 5”D Spacer Panel 1
18
18
23
17
13
13
27
19
RX723001HC
Parts List
ITEM NO PART NUMBER DESCRIPTION QTY
1 7225HC-01 TOP BACK PANEL 1
2 7230HC-02 SIDE PANEL ASSY-LH 1
3 7230HC-05 SIDE PANEL ASSY-RH 1
4 Z-M5X16SHDS M5-16MM SOCKET HEAD SCREW 2
5 Z-M10PLUG M10 PLASTIC HOLE PLUG 2
6 GAS STRUT (350) 350MM FULLY EXTENDED 2
7 POWER STRIP POWER STRIP W/USB OUTLET 1
8 RUBBER GROMMET-2 RUBBER GROMMET 2
9 7225HC-20 SPLICER POST ASSEMBLY 2
10 Z-SMS SHEET METAL SCREW 2
11 Z-M5X16PHMS M5X16MM PAN HEAD MS 25
13 Z-RB12M RUBBER BUMPER 12MM SQ 1
14 7225HC-22 HOLD-DOWN BRACKET 2
15 Z-M8-1.25-20SHS M8X20 SOCKET HEAD CAP SCREW 2
16 Z-WAFM8 M8 FLAT WASHER 2
17 7225HC-10 TOP LID ASSY 1
18 7225HC-13 FRONT LID SUB-ASSY 1
19 RXPTUSL UNIVERSAL POWER TOOL RACK 1
20 Z-M4-0.5LN M4-0.5 LOCKNUT 4
21 Z-MSM4-0.7X10MMPH M4-0.7X10MM PAN HEAD MS 4
1
21
17
16
14
22
20
22
28
15
16
RX553001HC
Parts List
ITEM NO PART NUMBER DESCRIPTION QTY
1 5525HC-01 TOP BACK PANEL 1
2 7230HC-02 SIDE PANEL ASSY-LH 1
3 7230HC-05 SIDE PANEL ASSY-RH 1
4 Z-M5X16SHDS M5-16MM SOCKET HEAD SCREW 2
5 Z-M10PLUG M10 PLASTIC HOLE PLUG 2
6 GAS STRUT (350) 350MM FULLY EXTENDED 2
7 POWER STRIP POWER STRIP W/USB OUTLET 1
8 RUBBER GROMMET-2 RUBBER GROMMET 2
9 7225HC-20 SPLICER POST ASSEMBLY 2
10 Z-SMS SHEET METAL SCREW 2
11 Z-M5X16PHMS M5X16MM PAN HEAD MS 18
13 Z-RB12M RUBBER BUMPER 12MM SQ 1
14 7225HC-22 HOLD-DOWN BRACKET 2
15 Z-M8-1.25-20SHS M8X20 SOCKET HEAD CAP SCREW 2
16 Z-WAFM8 M8 FLAT WASHER 2
17 5525HC-10 TOP LID ASSY 1
18 5525HC-13 FRONT LID SUB-ASSY 1
19 RXPTUSL UNIVERSAL POWER TOOL RACK 1
20 Z-M4-0.5LN M4-0.5 LOCKNUT 4
21 Z-MSM4-0.7X10MMPH M4-0.7X10MM PAN HEAD MS 4
23 7230 Spacer Panel
72”Wide x 5” Deep Spacer Panel
1
1
5530 Spacer Panel
Step 1: Attach Splicer Posts to Side Panels
Step 2: Install Side Panels on Roller Cabinet
a. Slide Splicer Post Assembly (#9) into bottom opening of the
left-hand Side Panel Assembly(#2).
NOTE: If the hutch is going to be used over the stainless
steel surface, then remove the spacer on the bottom of the
side panel.
b. Line up hole in Splicer Post with hole in Side Panel.
c. Insert Sheet Metal Screw (#10)
and tighten. Do not completely tighten
until hutch is fully assembled.
d. Repeat for the right-hand
side.
a. Remove plastic end caps from the top of the trim located at the
front corners of the roller cabinet.
b. Slide end of splicer channel into opening where plastic end
cap was located until side panel rests on top of MDF/Stainless
Steel Top.
c. Repeat process for right-hand side.
Plastic
End
Cap
Plastic End Cap
SPACER
2
Loading...