Extreme Networks Summit X150 Series, Summit X150-24p, Summit X150-24t, Summit X150-48t Installation Note
Summit X150 Series Switches Installation Note
This installation note describes how to install and remove the Summit X150 series switches.
This note includes the following sections:
● Safety on page 1
● Installing a Summit X150 Series Switch on page 2
● Connecting Power on page 3
● Connecting Power on page 3
● Removing a Summit X150 Series Switch from a Rack on page 3
NOTE
Optional external redundant power supplies are available for use with the Summit X150 series switches. When a
redundant power supply is used with a Summit X150 series switch, the power supplies (internal and redundant) are
fully fault tolerant and load-sharing. If one power supply fails, the other power supply will provide sufficient power to
operate the switch. The Summit X150-24t and X150-48t switches use the EPS-160 for redundant power; the
Summit X150-24p switch uses the EPS-500 for redundant power. Refer to the Summit Family Switches Hardware
Installation Guide for further details.
Safety
Only trained service personnel should perform service to Extreme Networks switches and their
components. Trained service personnel have read all related installation manuals, have the technical
training and experience necessary to be aware of the hazards to which they are exposed in performing a
task, and are aware of measures to minimize the danger to themselves or other persons.
Before installing a Summit X150 series switch into your network:
● Read the latest installation and safety information provided in the Summit Family Switches Hardware
Installation Guide.
● See Appendix A of the Summit Family Switches Hardware Installation Guide for additional information
regarding regulatory compliance certifications.
The Summit Family Switches Hardware Installation Guide can be downloaded from the following location:
http://www.extremenetworks.com/services/hardware-userguide.aspx.
NOTE
Die deutsche Version der für dieses Produkt von Extreme Networks relevanten Sicherheitshinweise finden sich im
Abschnitt “Sicherheitshinweise” im Summit Family Switches Hardware Installation Guide. Dieses
Installationshandbuch steht auf der folgenden Webseite zum Download zur Verfügung: http://
www.extremenetworks.com/services/hardware-userguide.aspx.
Part Number: 120404-00 Rev 01
1
3
Installing a Summit X150 Series Switch
CAUTION
Make sure that proper ESD controls are in use before maintenance is performed. This includes but is not limited to
wrist straps that are grounded to the switch chassis and earth grounds.
Installing a Summit X150 Series Switch
The Summit X150 series switch is designed to be installed in a standard 19-inch equipment rack or
placed free-standing on a tabletop. The installation process includes the following tasks:
● Install the switch in a rack or on a table.
● Ground the switch.
● Connect a redundant power supply (if applicable).
● Connect the internal power supply.
Rack-Mounting a Summit X150 Series Switch
To mount the switch in a rack, you will need the following tools, equipment, and resources:
● Mounting brackets (provided)
● Eight screws (provided) to secure the mounting brackets to the switch
● Four rack system mounting screws
The screw size will vary based on your organization’s rack; screws are not provided.
● Screwdriver for securing the switch to the rack
The screwdriver size will vary based on the requirements of your organization’s rack.
To rack-mount a Summit X150 series switch:
1 Place the switch upright on a secure work surface.
2 Place a mounting bracket over the mounting holes on one side of the unit.
3 Insert the screws and fully tighten (see Figure 1).
Figure 1: Attaching a Mounting Bracket
3
34
35
36
3
7
38
3
9
4
0
41
42
4443
4645 48
47
45
X
46
X
4
7
X
48X
S
ol
i
d
O
N
B
= Link
linkin
g =
Ac
t
ivity
Shar
ed
P
o
r
t
s
4 Repeat steps 2 and 3 for the other side of the switch.
2
SH_035
Summit X150 Series Switches Installation Note
Loading...