Extreme Networks RBT4102 User Manual

RoamAbout

RBT-4102, RBT-4102-BG, and RBT-4102-EU

2.4 GHz / 5 GHz

Wireless Access Point

Installation Guide

P/N 9034148-13

ELECTRICAL HAZARD: Only qualified personnel should
perform installation procedures.

Notice

ENTERASYS NETWORKS reserves the right to make changes in specifications and other
information contained in this document and its web site without prior notice. The reader should
in all cases consult ENTERASYS NETWORKS to determine whether any such changes have
been made.

The hardware, firmware, or software described in this document is subject to change without
notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING
BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS
DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF
ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE
KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.
50 Minuteman Road
Andover, MA 01810

© 2006 Enterasys Networks, Inc. All rights reserved.
Printed in Taiwan

Release Date: April 2006

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS ROAMABOUT, LANVIEW,
NETSIGHT, ROAMABOUT, WEBVIEW, and any logos associated therewith, are trademarks
or registered trademarks of Enterasys Networks, Inc. in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks
of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

i

Notice

Enterasys Networks, Inc.

Firmware License Agreement

BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,

CAREFULLY READ THIS LICENSE AGREEMENT.

This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys
Networks, Inc. on behalf of itself and its Affiliates (as hereinafter defined) (“Enterasys”) that
sets forth Your rights and obligations with respect to the Enterasys software program/firmware
installed on the Enterasys product (including any accompanying documentation, hardware or
media) (“Program”) in the package and prevails over any additional, conflicting or inconsistent
terms and conditions appearing on any purchase order or other document submitted by You.
“Affiliate” means any person, partnership, corporation, limited liability company, or other form
of enterprise that directly or indirectly through one or more intermediaries, controls, or is
controlled by, or is under common control with the party specified. This Agreement constitutes
the entire understanding between the parties, and supersedes all prior discussions,
representations, understandings or agreements, whether oral or in writing, between the parties
with respect to the subject matter of this Agreement. The Program may be contained in
firmware, chips or other media.

BY INSTALLING OR OTHERWISE USING THE PROGRAM, YOU REPRESENT THAT
YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER
(IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO
ACT, “YOU” AND “YOUR” SHALL BE DEEMED TO REFER TO SUCH ENTITY) AND
THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT,
WHICH INCLUDES, AMONG OTHER PROVISIONS, THE LICENSE, THE DISCLAIMER
OF WARRANTY AND THE LIMITATION OF LIABILITY. IF YOU DO NOT AGREE TO
THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO
THIS AGREEMENT, ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO
YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS
OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF
RECEIPT FOR A FULL REFUND.

IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT
ENTERASYS NETWORKS, LEGAL DEPARTMENT AT [phone].

You and Enterasys agree as follows:

1. LICENSE. You have the non-exclusive and non-transferable right to use only the one (1)

copy of the Program provided in this package subject to the terms and conditions of this
Agreement.

2. RESTRICTIONS. Except as otherwise authorized in writing by Enterasys, You may not,
nor may You permit any third party to:

(i) Reverse engineer, decompile, disassemble or modify the Program, in whole or in

part, including for reasons of error correction or interoperability, except to the extent
expressly permitted by applicable law and to the extent the parties shall not be
permitted by that applicable law, such rights are expressly excluded. Information
necessary to achieve interoperability or correct errors is available from Enterasys
upon request and upon payment of Enterasys’ applicable fee.

ii

Notice

(ii) Incorporate the Program, in whole or in part, in any other product or create derivative

works based on the Program, in whole or in part.
(iii) Publish, disclose, copy, reproduce or transmit the Program, in whole or in part.
(iv) Assign, sell, license, sublicense, rent, lease, encumber by way of security interest,

pledge or otherwise transfer the Program, in whole or in part.
(v) Remove any copyright, trademark, proprietary rights, disclaimer or warning notice

included on or embedded in any part of the Program.

3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws
and in the state and federal courts of the Commonwealth of Massachusetts without regard to its
conflicts of laws provisions. You accept the personal jurisdiction and venue of the
Commonwealth of Massachusetts courts. None of the 1980 United Nations Convention on
Contracts for the International Sale of Goods, the United Nations Convention on the Limitation
Period in the International Sale of Goods, and the Uniform Computer Information Transactions
Act shall apply to this Agreement.

4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject
to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce,
which prohibit export or diversion of certain technical products to certain countries, unless a
license to export the Program is obtained from the U.S. Government or an exception from
obtaining such license may be relied upon by the exporting party.

If the Program is exported from the United States pursuant to the License Exception CIV
under the U.S. Export Administration Regulations, You agree that You are a civil end user of the
Program and agree that You will use the Program for civil end uses only and not for military
purposes.

If the Program is exported from the United States pursuant to the License Exception TSR
under the U.S. Export Administration Regulations, in addition to the restriction on transfer set
forth in Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program,
the source code for the Program or technology to a national of a country in Country Groups D:1
or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the
People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine,
Uzbekistan, Vietnam, or such other countries as may be designated by the United States
Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct product of
the Program or the technology, if such foreign produced direct product is subject to national
security controls as identified on the U.S. Commerce Control List, or (iii) if the direct product of
the technology is a complete plant or any major component of a plant, export to Country Groups
D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced
direct product is subject to national security controls as identified on the U.S. Commerce
Control List or is subject to State Department controls under the U.S. Munitions List.

5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Program
(i) was developed solely at private expense; (ii) contains “restricted computer software”
submitted with restricted rights in accordance with section 52.227-19 (a) through (d) of the
Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all
respects is proprietary data belonging to Enterasys and/or its suppliers. For Department of
Defense units, the Program is considered commercial computer software in accordance with
DFARS section 227.7202-3 and its successors, and use, duplication, or disclosure by the
Government is subject to restrictions set forth herein.

iii

Notice

6. DISCLAIMER OF WARRANTY. EXCEPT FOR THOSE WARRANTIES
EXPRESSLY PROVIDED TO YOU IN WRITING BY ENTERASYS, ENTERASYS
DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON­INFRINGEMENT WITH RESPECT TO THE PROGRAM. IF IMPLIED WARRANTIES
MAY NOT BE DISCLAIMED BY APPLICABLE LAW, THEN ANY IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THIRTY (30) DAYS AFTER
DELIVERY OF THE PROGRAM TO YOU.

7. LIMITATION OF LIABILITY. IN NO EVENT SHALL ENTERASYS OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING,
WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF
THE USE OR INABILITY TO USE THE PROGRAM, EVEN IF ENTERASYS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS FOREGOING
LIMITATION SHALL APPLY REGARDLESS OF THE CAUSE OF ACTION UNDER
WHICH DAMAGES ARE SOUGHT.

THE CUMULATIVE LIABILITY OF ENTERASYS TO YOU FOR ALL CLAIMS
RELATING TO THE PROGRAM, IN CONTRACT, TORT OR OTHERWISE, SHALL NOT
EXCEED THE TOTAL AMOUNT OF FEES PAID TO ENTERASYS BY YOU FOR THE
RIGHTS GRANTED HEREIN.

8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights
associated with the Program are of critical value to Enterasys and, accordingly, You hereby agree
to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii)
the use, copying and deployment of the Program. You also grant to Enterasys and its authorized
representatives, upon reasonable notice, the right to audit and examine during Your normal
business hours, Your books, records, accounts and hardware devices upon which the Program
may be deployed to verify compliance with this Agreement, including the verification of the
license fees due and paid Enterasys and the use, copying and deployment of the Program.
Enterasys’ right of examination shall be exercised reasonably, in good faith and in a manner
calculated to not unreasonably interfere with Your business. In the event such audit discovers
non-compliance with this Agreement, including copies of the Program made, used or deployed
in breach of this Agreement, You shall promptly pay to Enterasys the appropriate license fees.
Enterasys reserves the right, to be exercised in its sole discretion and without prior notice, to
terminate this license, effective immediately, for failure to comply with this Agreement. Upon
any such termination, You shall immediately cease all use of the Program and shall return to
Enterasys the Program and all copies of the Program.

9. OWNERSHIP. This is a license agreement and not an agreement for sale. You
acknowledge and agree that the Program constitutes trade secrets and/or copyrighted material of
Enterasys and/or its suppliers. You agree to implement reasonable security measures to protect
such trade secrets and copyrighted material. All right, title and interest in and to the Program
shall remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall
be reserved to Enterasys.

iv

Notice

10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of
this Agreement by You may cause Enterasys irreparable damage for which recovery of money
damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief
to protect Enterasys’ rights under this Agreement in addition to any and all remedies available
at law.

11. ASSIGNMENT. You may not assign, transfer or sublicense this Agreement or any of
Your rights or obligations under this Agreement, except that You may assign this Agreement to
any person or entity which acquires substantially all of Your stock or assets. Enterasys may
assign this Agreement in its sole discretion. This Agreement shall be binding upon and inure to
the benefit of the parties, their legal representatives, permitted transferees, successors and
assigns as permitted by this Agreement. Any attempted assignment, transfer or sublicense in
violation of the terms of this Agreement shall be void and a breach of this Agreement.

12. WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this
Agreement must be in writing and will not be construed as a waiver of any subsequent breach of
such term or condition. Enterasys’ failure to enforce a term upon Your breach of such term shall
not be construed as a waiver of Your breach or prevent enforcement on any other occasion.

13. SEVERABILITY. In the event any provision of this Agreement is found to be invalid,
illegal or unenforceable, the validity, legality and enforceability of any of the remaining
provisions shall not in any way be affected or impaired thereby, and that provision shall be
reformed, construed and enforced to the maximum extent permissible. Any such invalidity,
illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or
unenforceable such provision in any other jurisdiction.

14. TERMINATION. Enterasys may terminate this Agreement immediately upon Your
breach of any of the terms and conditions of this Agreement. Upon any such termination, You
shall immediately cease all use of the Program and shall return to Enterasys the Program and all
copies of the Program.

v

Notice

vi

Compliances

RBT-4102

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to
channels 1 through 11.

IMPORTANT NOTE:
FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 70 centimeters (27.5 inches) between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.

vii

Wireless 5 GHz Band Statements:

A

As the Access Point can operate in the 5150-5250 MHz frequency band it is limited by the
FCC, Industry Canada and some other countries to indoor use only so as to reduce the
potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of the
5250-5350 MHz and 5650-5850 MHz bands. These radars could cause interference and /
or damage to the access point when used in Canada.

The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
“Digital Apparatus,” ICES-003 of Industry Canada.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur:
“Appareils Numériques,” NMB-003 édictée par l’Industrie.

Industry Canada Statement

Operation is subject to the following two conditions:

1) This device may not cause interference and

2) This device must accept any interference, including interference that may cause
undesired operation of the device

This device has been designed to operate with an antenna having a maximum gain of
23 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry
Canada. The required antenna Impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the EIRP is not more than required for successful communication.

Because high power radars are allocated as primary users (meaning they have priority) in
5250-5350 MHz, these radars could cause interference and/or damage to license exempt
LAN devices.

RBT-4102-EU

Australia/New Zealand AS/NZS 4771

N826

viii

Japan Telec Approval

003NY05152
003GZ05053
003WY05076
003UX05009

EC Conformance Declaration

Marking by the above symbol indicates compliance with the Essential Requirements of
the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the
following conformance standards:

• EN 60950 (IEC 60950) - Product Safety

• EN 301 893 - Technical requirements for 5 GHz radio equipment

• EN 300 328 - Technical requirements for 2.4 GHz radio equipment

• EN 301 489-1 / EN 301 489-17 - EMC requirements for radio equipment

Countries of Operation & Conditions of Use in the European
Community

This device is intended to be operated in all countries of the European Community.
Requirements for indoor vs. outdoor operation, license requirements and allowed
channels of operation apply in some countries as described below:

Note: The user must use the configuration utility provided with this product to ensure the

channels of operation are in conformance with the spectrum usage rules for
European Community countries as described below.

• This device requires that the user or installer properly enter the current country of

operation in the command line interface as described in the user guide, before operating
this device.

• This device will automatically limit the allowable channels determined by the current

country of operation. Incorrectly entering the country of operation may result in illegal
operation and may cause harmful interference to other system. The user is obligated to
ensure the device is operating according to the channel limitations, indoor/outdoor
restrictions and license requirements for each European Community country as
described in this document.

• This device employs a radar detection feature required for European Community

operation in the 5 GHz band. This feature is automatically enabled when the country of
operation is correctly configured for any European Community country. The presence of
nearby radar operation may result in temporary interruption of operation of this device.
The radar detection feature will automatically restart operation on a channel free of
radar.

• The 5 GHz Turbo Mode feature is not allowed for operation in any European Community

country. The current setting for this feature is found in the 5 GHz 802.11a Radio Settings
Window as described in the user guide.

• The 5 GHz radio's Auto Channel Select setting described in the user guide must always

remain enabled to ensure that automatic 5 GHz channel selection complies with
European requirements. The current setting for this feature is found in the 5 GHz

802.11a Radio Settings Window as described in the user guide.

ix

• This device is restricted to indoor use when operated in the European Community using
the 5.15 - 5.35 GHz band: Channels 36, 40, 44, 48, 52, 56, 60, 64.

• This device may be operated indoors or outdoors in all countries of the European
Community using the 2.4 GHz band: Channels 1 - 13, except where noted below.

- In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band:
Channels 1 - 7.

Operation Using 5 GHz Channels in the European Community

The user/installer must use the provided configuration utility to check the current channel
of operation and make necessary configuration changes to ensure operation occurs in
conformance with European National spectrum usage laws as described below and
elsewhere in this document.

Allowed 5GHz Channels in Each European Community Country

Allowed Frequency Bands Allowed Channel Numbers Countries

5.15 - 5.35* & 5.470 - 5.725 GHz 36, 40, 44, 48, 52, 56, 60, 64,
100, 104, 108, 112, 116, 120,
124, 128, 132, 136, 140

5 GHz Operation Not Allowed None Greece, Hungary
* Outdoor operation is not allowed using 5.15-5.35 GHz bands (Channels 36 - 64).

Austria, Belgium,
Cyprus, Czech
Republic, Denmark,
Estonia, Finland,
France, Germany,
Iceland, Ireland, Italy,
Latvia, Liechtenstein,
Lithuania,
Luxembourg, Malta,
Netherlands, Norway,
Poland, Portugal,
Slovakia, Slovenia,
Spain, Sweden,
Switzerland, U.K.

x

EC-Konformitätserklärung

Die Kennzeichnung mit dem obigen Symbol zeigt die Übereinstimmung mit den wichtigen
Anforderungen der R&TTE-Direktive der Europäischen Union (1999/5/EC) an. Dieses
Gerät erfüllt die folgenden Konformitätsstandards:

• EN 60950 (IEC 60950) - Produktsicherheit

• EN 301 893 - Technische Anforderungen für 5-GHz-Hochfrequenzgeräte

• EN 300 328 - Technische Anforderungen für 2,4-GHz-Hochfrequenzgeräte

• EN 301 489-1 / EN 301 489-17 - EMV-Anforderungen für Hochfrequenzgeräte

Betriebsländer und Bedingungen für die Verwendung in der
Europäischen Gemeinschaft

Dieses Gerät ist für den Betrieb in allen Ländern der Europäischen Gemeinschaft
vorgesehen. Anforderungen für den Betrieb in Räumen bzw. im Freien,
Lizenzbedingungen und zulässige Betriebskanäle treffen entsprechend der folgenden
Ausführung zu:

Hinweis:Der Benutzer muss das für das Gerät bereitgestellte Konfigurationsprogramm

• Bevor dieses Gerät in Betrieb genommen wird, muss der Benutzer oder Installierende

• Durch die Festlegung des Betriebslands werden automatisch die zulässigen Kanäle

• Dieses Gerät verfügt über eine Radarerkennungsfunktion, die für den Betrieb im

• Der 5-GHz-Turbomodus wird in keinem Land der Europäischen Gemeinschaft

• Die im Benutzerhandbuch beschriebene Auto Channel Select-Einstellung des

verwenden, um sicherzustellen, dass die Betriebskanäle mit den unten
beschriebenen Vorschriften zur Verwendung des Spektrums für die
Europäische Gemeinschaft übereinstimmen.

für dieses Gerät entsprechend der Bedienungsanleitung in die Befehlszeile das richtige
Betriebsland eingeben.

begrenzt. Eine falsche Eingabe des Betriebslands kann zu einem illegalen Betrieb
führen und schädliche Interferenzen bei anderen Systemen verursachen. Der Benutzer
muss sicherstellen, dass das Gerät entsprechend der Kanallimitierung, den
Beschränkungen für den Betrieb in Räumen und im Freien und den Lizenzbedingungen
jedes in dieser Dokumentation beschriebenen Lands der Europäischen Gemeinschaft
betrieben wird.

5-GHz-Band in der Europäischen Gemeinschaft erforderlich ist. Diese Funktion wird
automatisch aktiviert, wenn für das Land der Europäischen Gemeinschaft die
Betriebslandeinstellung richtig konfiguriert wurde. Ein Radarbetrieb in der Nähe kann zu
einer vorübergehenden Betriebsunterbrechung dieses Geräts führen. Die
Radarerkennungsfunktion sorgt dafür, dass das Gerät den Betrieb automatisch auf
einem radarfreien Kanal neu startet.

zugelassen. Die aktuelle Einstellung für diese Funktion ist wie im Benutzerhandbuch
beschrieben im Fenster "5 GHz 802.11a Radio Settings" zu finden.

5-GHz-Radios muss immer aktiviert bleiben, um sicherzustellen, dass die automatische
5-GHz-Kanalwahl den Anforderungen der Europäische Gemeinschaft entspricht. Die
aktuelle Einstellung für diese Funktion ist wie im Benutzerhandbuch beschrieben im
Fenster "5 GHz 802.11a Radio Settings" zu finden.

xi

• Bei der Verwendung des Geräts in der Europäische Gemeinschaft im 5,15 - 5,35
GHz-Band ist es auf die Verwendung in Räumen beschränkt: Kanäle 36, 40, 44, 48, 52,
56, 60, 64.

• Bei der Verwendung des 2,4-GHz-Bands darf das Gerät in allen Ländern der
Europäischen Gemeinschaft sowohl in Räumen als auch im Freien benutzt werden:
Kanäle 1 - 13, außer wenn unten aufgeführt.

- In Frankreich ist der Betrieb im Freien nur bei der Verwendung des 2,4 - 2,454
GHz-Bands zugelassen: Kanäle 1 - 7.

Betrieb bei Verwendung der 5-GHz-Kanäle in der Europäische
Gemeinschaft

Der Benutzer/Installierende muss das für das Gerät bereitgestellte
Konfigurationsprogramm verwenden, um den aktuellen Betriebskanal zu prüfen und um
die erforderlichen Einstellungen zu konfigurieren, damit das Gerät entsprechend der
Gesetze zur Verwendung des Spektrums für die Europäische Gemeinschaft, die
nachfolgend und in der gesamten Dokumentation beschrieben werden, betrieben wird.

Zulässige 5-GHz-Kanäle in der Europäischen Gemeinschaft

Zulässige Frequenz-bänder Zulässige Kanalnummern Länder

5.15 - 5.35* & 5.470 - 5.725 GHz 36, 40, 44, 48, 52, 56, 60, 64,
100, 104, 108, 112, 116, 120,
124, 128, 132, 136, 140

5 GHz Operation Not Allowed None Griechenland, Ungarn
* Der Betrieb in den Bändern 5,15 - 5,35 GHz ist im Freien nicht zulässig (Kanäle 36 -64).

Frankreich, Schweiz,
Liechtenstein ,
Österreich, Belgien,
Zypern, Tschechien,
Dänemark, Estland,
Finnland, Deutschland,
Island, Irland, Italien,
Lettland, Litauen,
Luxemburg, Malta,
Niederlande,
Norwegen, Polen,
Portugal, Slowakei,
Slowenien, Spanien,
Schweden, UK

xii

Declaration of Conformity in Languages of the European Community

English Hereby, Enterasys, declares that this Radio LAN device is in compliance

Finnish (FI) Valmistaja Enterasys vakuuttaa täten että Radio LAN device tyyppinen

Dutch (NL) Hierbij verklaart Enterasys dat het toestel Radio LAN device in overeen-

French (FR) Par la présente Enterasys déclare que l'appareil Radio LAN device est

Swedish (SE) Härmed intygar Enterasys att denna Radio LAN device står I överens-

Danish (DK) Undertegnede Enterasys erklærer herved, at følgende udstyr Radio LAN

German (DE) Hiermit erklärt Enterasys, dass sich dieser/diese/dieses Radio LAN de-

with the essential requirements and other relevant provisions of Directive
1999/5/EC.

A copy of the original Declaration of conformity can be obtained from En­terasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.

Yhdenmukaisuuden alkuperäisen julistuksen kopio voidaan saada En­terasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

stemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG.

Bij deze Enterasys dat deze Radio LAN device voldoet aan de essentiële
eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.

Een exemplaar van de oorspronkelijke Verklaring van overeenstemming
kan worden verkregen uit Enterasys Networks, 50 Minuteman Road, An­dover, Ma 01810, USA.

conforme aux exigences essentielles et aux autres dispositions perti­nentes de la directive 1999/5/CE.

Une copie de la déclaration originale de la conformité peut être obtenue
à partir Enterasys Networks, 50 Minuteman Road, Andover, Ma 01810,
USA.

stämmelse med de väsentliga egenskapskrav och övriga relevanta be­stämmelser som framgår av direktiv 1999/5/EG.

EN kopia om original Tillkännagivande av likheten kanna bli få från En­terasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

device overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.

EN afskrift i den selvstændig Påstand i lighed kan opnåede af Enterasys
Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

vice in Übereinstimmung mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet".

Eine Kopie der ursprünglichen Erklärung der Übereinstimmung kann von
erhalten werden Enterasys Networks, 50 Minuteman Road, Andover, Ma
01810, USA.

xiii

Greek (GR) µε την παρουσα Enterasys δηλωνει οτι radio LAN device συµµορφωνεται

Italian (IT) Con la presente Enterasys dichiara che questo Radio LAN device è con-

Spanish (ES) Por medio de la presente Enterasys declara que el Radio LAN device

Portuguese
(PT)

προσ τισ ουσιωδεισ απαιτησεισ και τισ λοιπεσ σΧετικεσ διαταξεισ τησ
οδηγιασ 1999/5/εκ.

Ένα αντίγραφο της αρχικής ∆ιακήρυξης της συµµόρφωσης µπορεί να
ληφθεί από Enterasys Networks, 50 Minuteman Road, Andover, Ma

01810, USA.

forme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.

Una copia della dichiarazione originale di conformità può essere ottenuta
da Enterasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.

Una copia del declaración original de la conformidad se puede obtener
de Enterasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

Enterasys declara que este Radio LAN device está conforme com os req­uisitos essenciais e outras disposições da Directiva 1999/5/CE.

Uma cópia da declaração original do conformity pode ser obtida de En­terasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.

Safety Compliance

Power Cord Safety

Please read the following safety information carefully before installing the access
point:

WAR NING: Installation and removal of the unit must be carried out by qualified personnel

only.

• The unit must be connected to an earthed (grounded) outlet to comply with international
safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)
connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a
configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove
power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC

60950. The conditions are only maintained if the equipment to which it is connected
also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT
must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the
secondary connection point labelled Neutral, connected directly to earth (ground).

†

Impédance à la terre

†

supplies. If your supplies are of IT type, this unit

xiv

Important! Before making connections, make sure you have the correct cord set. Check
it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least
10 A

The attachment plug must be an earth-grounding type with
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V)
configuration.

Denmark The supply plug must comply with Section 107-2-D1, Stan-

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

dard DK2-1a or DK2-5a.

be fitted with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).

The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le access

point:
AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il
n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de
respecter les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit
respecter une configuration qui permet un branchement sur une entrée d’appareil EN
60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile.
Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique
au niveau de cette prise.

xv

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à
la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il
est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos
alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une
tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec
un point secondaire de connexion portant l’appellation Neutre et avec raccordement
direct à la terre (masse).

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE

Europe La prise secteur doit être conforme aux normes CEE 7/7

de la CSA.

Les spe'cifications minimales pour un cable flexible sont AWG
No. 18, ouAWG No. 16 pour un cable de longueur infe'rieure
a` 2 me'tres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal
d’au moins 10 A.

La prise femelle de branchement doit être du type à mise à la
terre (mise à la masse) et respecter la configuration NEMA
5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).

de la norme DK2 1a ou DK2 5a.

1011.

(“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC>
et doit être de type HO3VVF3GO.75 (minimum).

Bitte unbedingt vor dem Einbauen des Access Point die folgenden
Sicherheitsanweisungen durchlesen (Germany):

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal

erfolgen.

• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen
werden.

• Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die
internationalen Sicherheitsnormen erfüllt.

• Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker)
muß einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

xvi