Extra Miles UTRACK MVT600 User Manual

- 1 -

UTRACK MVT600 User Guide Version 3.0

UTRACK® GPS Vehicle Tracker

MVT600 User Guide

- 2 -

UTRACK MVT600 User Guide Version 3.0

Contents

1. Copyright and Disclaimer ...........................................................................................................................- 3 -

2.

A

pplications................................................................................................................................................. - 3 -

3. Product Function and S

pec

ifications ......................................................................................................... - 3 -

3.1 Product Function .......................................................................................................................................... - 3

-

3.2

Specifications ...................................................................................................................................................

- 4 -

4. MVT600 and Accessories ...........................................................................................................................- 5 -

5. V iew.............................................................................................................................................................- 5 -

6. First

Use

....................................................................................................................................................... - 6 -

6.1 Install SIM Card ................................................................................................................................................ - 6 -

6.2 Charging ...........................................................................................................................................................- 6 -

6.3 LED Indications................................................................................................................................................. - 6 -

6.4 Track by Calling ................................................................................................................................................ - 7 -

6.4.1 Multiple Phone numbers– A71 ........................................................................................................... - 8 -

6.4.2 Listening-in (Voice

Monitoring)–A72 ..................................................................................................

- 8 -

6.4.3 Sleep Mode – A73 ................................................................................................................................- 9 -

6.4.4 Geo-fence Alarm –

B05

........................................................................................................................ - 9 -

6.4.5 Set Anti-theft – B21...............................................................................................................- 10 -

6.4.6 T ime Zone– B35.....................................................................................................................- 10 -

6.5 Configure by

Computer

.................................................................................................................................- 10 -

6.5.1 SMS Tracking.......................................................................................................................................- 12 -

6.5.2 GPRS

Tracking

.....................................................................................................................................- 15 -

7 Installation............................................................................................................................................................- 17 -

7.1 Install I/O Cable..............................................................................................................................................- 17 -

Power/GND (PIN1/PIN2)..............................................................................................................................- 18 -

7.1.2 Digital Input (PIN4/5, negative triggering) ........................................................................................- 18 -

7.1.3 Digital Input (PIN3, positive

triggering)

............................................................................................- 18 -

7.1.4 Output .................................................................................................................................................- 19 -

7.1.5 Analog Input .......................................................................................................................................- 19 -

7.1.6 Install Handset Phone (RS232 In

terface

) ..........................................................................................- 20 -

7.1.7 Install Camera (RS232 In

terface

) .......................................................................................................- 20 -

7.1.8 Install Micro SD...................................................................................................................................- 21 -

7.1.9 Install RFID Reader (Wiegand Interface)...........................................................................................- 21 -

7.2 Install GPS/GSM

Antennas

............................................................................................................................- 21 -

7.3 Mount the MVT600 unit ...............................................................................................................................- 22 -

- 3 -

UTRACK MVT600 User Guide Version 3.0

1. Copyright and

Disclaimer

The user manual may be changed without prior notification.

This user manual, or any part thereof, may not be reproduced for any purpose whatsoever without the written

authorization of Extra Miles Solutions, or transmitted in any form, either electronically or mechanically, including

photocopying and recording.

In no event shall Extra Miles Solutions be liable for direct, indirect, special, incidental, or consequential damages

(including but not limited to economic loss, personal injury, and loss of asset and property) arising out of the use

or inability or illegality to use the product or documentation.

2.

Applications

 Vehicle Real Time Tracking  Car Security/Anti-Hijack  Fleet Management

3. Product Function and

Specifications

3.1 Product Function

 SiRF III GPS and Quad Band GSM 850/900/1800/1900Mhz  AGPS (with GSM Base Station ID)  Track by SMS/GPRS (UTRACK SMS Protocol)  Track on Demand  Track by T ime Interval  Track by Distance Interval  Track on Mobile Phone  Listen-in or Two-way Audio (Optional)  Internal Flash Memory (8M)  Inbuilt Accelerating Sensor  Inbuilt Motion Sensor  Internal Backup Battery  SOS Alarm  Geo-fence Alarm  GPS Blind Area Alarm  Low Battery Alarm

- 4 -

UTRACK MVT600 User Guide Version 3.0

 Speeding Alarm  Tow Alarm  GPS Antenna Cut Alarm  External Power Cut Alarm  Mileage Report  Engine Cut (Engine immobilization)  Inbuilt Super Magnet (optional)  Handset Phone (optional)  Camera (optional)  Micro SD Card Memory for Storing Pictures (Optional)  RFID Reader (optional)  LED Display (optional)  LCD Display (optional)  3 Digital Inputs  3 Outputs  3 Analog Input Detection

3.2 Specifications

Items

Specifications

Dimension

103*98*32mm

Weight

220g

Input Voltage

DC 9V~36V/1.5A

Back-up Battery

850mAh/3.7V

Power

consumption

85mA standby current

Operating

Temperature

-20℃~55℃

Humidity

5%~95%

Work T ime

36 hours in power-saving mode and 8 hours in normal mode

LED

2 LED lights to show GPS, GSM and other status

Button

1 SOS and 1 power on/off

Microphone

Optional

Memory

8M Byte

Sensor

Motion and Accelerating sensor

GSM Frequency

GSM 850/900/1800/1900MHz

GPS Chip

Latest GPS SIRF-Star III chipset

GPS Sensitivity

-159dB

Positioning

Accuracy

10 meters, 2D RMS

I/O

3 Digital Input ( 1 positive triggering and 2 negative triggering)

- 5 -

UTRACK MVT600 User Guide Version 3.0

3 Analog Input Detection

3 Output

4 RS232 Interface

4. MVT600 and

Accessories

MVT600 with

GPS

GSM

I/O Cable +

USB Data Cable

CD

Battery

Antenna

SOS Button

Optional Accessories

Camera (connect

max 2 cameras)

Handset

Phone

RFID Reader A21 LCD Player (dialing,

show SMS)

5.

View

GPS LED

Mic./Speaker

SIM

GSM LED

GPS Antenna

USB Port

Micro SD

On/Off

GSM Antenna

Power, I/O Handset

Camera Camera RS232 RFID Reader

- 6 -

UTRACK MVT600 User Guide Version 3.0

6. First

Use

6.1 Install SIM Card

Check that the SIM has not run out of credit (test the SIM in a phone to make sure it

can send and receive SMS);

Check that the SIM Lock code is turned off;

If you require the function of sending an SMS location report to the authorized phone

number when it makes a call to the MVT600, please make sure the SIM installed

supports displaying caller ID.

Before installing the SIM card, turn off the power for MVT600.

Unscrew and remove cover.

Insert the SIM card by sliding it into the card holder with the chip module facing to

the connectors on PCB.

Replace the cover and screw it in.

6.2 Charging

Please connect GND (-Black) and Power (+Red) wires to 12V or 24 external power and make sure to charge the

battery for at least 3 hours. 8 hours is highly appreciated.

Configuration and testing suggested be prior to installation.

6.3 LED Indications

GPS LED (blue)

GSM LED (green)

On/Off

Press and hold the Power On/Off button for 3~5 seconds to turn on/off MVT600.

GPS LED (Blue)

On

One button is pressed or input is active.

Flashing ( every 0.1 second)

Initializing or back-up battery power is low

Flashing (0.1 second on and 2.9 seconds off)

MVT600 has a GPS fix

Flashing (1 second on and 2 seconds off)

MVT600 has no GPS fix

GSM LED (Green)

On

A call is coming in / a call is being made

Flashing ( every 0.1 second)

Initializing

- 7 -

UTRACK MVT600 User Guide Version 3.0

Flashing (0.1 second on and 2.9 seconds off)

MVT600 is connected to the GSM network

Flashing (1 second on and 2 seconds off)

MVT600 is not connected to the GSM network

6.4 Track by Calling

Make a call to MVT600 and it will report with one SMS.

For example,

Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329

&ie=UTF8&z=16&iwloc=addr&om=1

Click on the link then the location can be shown directly on Google Maps on your mobile phone.

Report description:

Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329

&ie=UTF8&z=16&iwloc=addr&om=1

Content

Description

Note

Now

Current Location

Alarm Type

110721 16:40

Date & T ime: 21 July, 2011, 16:40pm

Date & T ime in YYMMDD HH:MM

V

No GPS fixed

GPS Status Indicator:

A = valid, V = invalid

10

GSM signal=10

GSM Signal. Decimal Digit (0~31)

0Km/h

Speed=0

KM/h. Decimal digit

97%

Battery Power: 97%

Battery Power Balance (Percentage)

http://maps.google.c

om/maps?f=q&hl=en

&q=22.540103,114.0

82329&ie=UTF8&z=1

6&iwloc=addr&om=1

Latitude: 22.513015

Longitude: 114.057235

Google Maps Web Link with Latitude and

Longitude. Click on the link to get the

location.

If your mobile cannot visit HTTP websites, input the latitude and longitude into Google Maps as the following

picture shows to get the position:

- 8 -

UTRACK MVT600 User Guide Version 3.0

More SMS commands

You can configure MVT600 by mobile phone or by computer using the Parameter Editor. For more

details, please refer to part 6.5 Configure by Computer.

Note:

1. Password is 4 digits only and defaulted as 0000. You can change the password by Parameter Editor and SMS

command.

2. MVT600 will only accept commands from a user with the correct password and report SMS report to the user.

If preauthorized phone number was set, only this phone number can receive SMS reports.

6.4.1 Multiple Phone numbers– A71

Command: 0000, A71, phone number 1, phone number 2, phone number 3

SMS Get: IMEI, A71, OK Note：

Authorize a phone number for SOS alarm, calling for location report, geo-fence alarm, and low battery alarm.

Phone Number: Max 16 characters.

If no preset phone number, it is empty (default is empty).

Send command “0000, A71” to delete all phone numbers.

When the SOS button is pressed, MVT600 will make a call to phone number 1, 2 and 3. It will stop calling when

one number answers.

Example: 0000,A71,13811111111,13822222222,13833333333

SMS Get: 353358017784062,A71,OK

6.4.2 Listening-in (Voice Monitoring)–A72

Command: 0000, A72, phone number 1, phone number 2

SMS Get: IMEI, A72, OK

Note:

- 9 -

UTRACK MVT600 User Guide Version 3.0

Authorize a phone number to make a silent call to the t racker. The tracker will answer the call automatically and

allows the caller to listen to what is happening around the tracker. There is no sound when the tracker is working.

Phone Number: 2 monitoring numbers at the most can be set, 16 characters per number.

If no preset phone number, it is empty (default).

If no phone number, but has “,”, the number related to this “,” is deleted.

Send command “0000, A72” to delete all phone numbers.

Example: 0000,A72,13844444444,13855555555

SMS Get: 353358017784062,A72,OK

6.4.3 Sleep Mode – A73

Command: 0000,A73,X

SMS Get: IMEI,A73,OK

Note:

This setting is for power saving.

X=0, turn off sleep mode (default)

X=1, normal sleep. GSM module work, GPS module work by sleep mode intermittently. The device can work 25%

longer than no sleep mode. Note: this is not recommended for users who set “track by interval” or short time

interval, because it will affect the completeness of tracking.

X=2, deep sleep, the tracker will enter this mode after it is inactive or stationary (No SOS/any triggered by the

button/input/incoming calls/message/movement) for 5 minutes. GPS module stops working and GSM module

enters sleep mode. The tracker remains in this mode until it is activated by SOS/any triggered by the

button/input/incoming calls/message/movement. After that, it will repeat above processes.

Note: In any condition, the device will directly quit the sleep mode and back to normal working mode by SMS or

GPRS command to turn off the sleep mode.

Example: 0000,A73,2

SMS Get: 353358017784062,A73,OK

6.4.4 Geo-fence Alarm – B05

Command: B05,P,latitude,longitude,radius,in,out

SMS Get: IMEI,B05,OK

Note:

P: 1 to 8. Max 8 Geo-fence waypoints can be set.

Latitude: Latitude in decimal degrees of the waypoint center.

Longitude: Longitude in decimal degrees of the waypoint center.

Radius: [1, 4294967295] in meters.

In = 0, turn off the alarm when the tracker enters the waypoint;

In = 1, turn on the alarm when the tracker enters the waypoint.

Out = 0, turn off the alarm when the tracker exits the waypoint;

Out = 1, turn on the alarm when the tracker exits the waypoint.

- 10 -

UTRACK MVT600 User Guide Version 3.0

Example: 0000,B05,1,22.91319,114.07988,1000,0,1

SMS Get: 353358017784062,B05,OK

Once the tracker goes outside of the circle (center: 22.91319,114.07988 and radius 1000 meters), the following

message will be received.

353358017784062,ExitGEO,22.918186,114.089823,080229123816,A,10,22,16,32,1,21,6667,850,,0000

6.4.5 Set Anti-theft – B21

Command: 0000,B21,Status

SMS Get: IMEI,B21,OK

Note:

Status=1, turn on Anti-theft (default); the device alarms when input 2 (negative input) and input 3 (positive input)

are active;

Status=0, turn off Anti-theft; the device doesn’t alarm when input 2 (negative input) and input 3 (positive input)

are active.

6.4.6 T ime Zone– B35

Command: 0000,B35,T

SMS Get: IMEI,B35,OK

Note:

Default time of the tracker is GMT. You can use this command to change the time on your tracker to your local

time. This command is for SMS tracking only.

T ime zone of SMS report is separated with that of GPRS data. If you need to set time zone in GPRS data, please

use SMS command: 0000, B36, T

T=0, to turn off this function.

T=[-32768,32767] to set time difference in minutes to GMT.

For those ahead of GMT, just input the time difference in minutes directly. For example, GMT+8, W000000,032,480

‘-‘is required for those behind GMT. For example, W000000,032,-120.

Example: 0000,B35,480

SMS Get: 353358017784062,B35,OK

For more details regarding SMS commands, please refer to UTRACK SMS Protocol.

6.5 Configure by Computer

This part shows you the basics in how to use the Parameter Editor. Note: Don’t

connect MVT600 to external battery when configuring.

Please refer to the Parameter Editor User Guide for more detailed information regarding configuration and

functions.

- 11 -

UTRACK MVT600 User Guide Version 3.0

Run ‘PL2303_Prolific_DriverInstaller’ to install the driver for the USB data cable.

Note: PL2303_Prolific_DriverInstaller is in the folder ‘USB-232 Dri

ver

’ in the CD.

Connect the USB Data Cable between MVT600 and PC.

Open Device Manager (Device Manager is under Control Panel\System and Security\System). You can then find

‘Prolific USB-to-Serial Comm Port’ as the following picture shows.

Note: Remember this Com number. It needs to be input into the Parameter Editor. It is COM3 in this example and

it would be COM4 or COM5… in your computer.

Run ‘Parameter Editor.exe’ and the following configuration window will pop up:

- 12 -

UTRACK MVT600 User Guide Version 3.0

Choose the correct Com number and terminal type in previous Device Manager then click the ‘Open Port’ button.

Click ‘Read Settings’ button to show the default or previous settings of the tracker.

Note: Parameter Editor is in the CD. The language will be automatically adjusted to be the same as your PC

operation system’s language. Please use “Ctrl+L” to change the language.

6.5.1 SMS Tracking

6.5.1.1 Track by Preset Interval

Click Tap I: SMS Tracking

Item

Description

User Password

SMS password for sending SMS commands and defaulted as 0000.

Phone Number

A phone number to receive SMS location reports.

SMS Report Interval

Track by time interval via SMS.

Set time interval for SMS location report.

= 0, stop tracking by time interval (default);

= [1,65535], track by interval in minute.

Auto Report T imes

= 0, unlimited times for report.

- 13 -

UTRACK MVT600 User Guide Version 3.0

= [1,255], it will stop reporting when reaching preset times

Read

Read current tracker’s settings for above items.

Write

Write above settings to the tracker.

6.5.1.2 SMS Report

Click Tap V: Authorization

Item

Description

Authorization Phone

A phone number to receive selected event’s SMS reports.

Event

Selected event’s SMS reports will be sent to the authorized phone

number.

For more details, please refer to GPRS/SMS Protocol.

For description of events from SOS/Input 1 Active to Tow Alarm,

please refer to tap II GPRS Tracking.

Other events description, please refer to below chart.

Read

Read current tracker’s settings for above items.

Write

Write above settings to the tracker.

- 14 -

UTRACK MVT600 User Guide Version 3.0

Event Description:

Event

Description

(If the box is ticked, authorized phone number will get event report

by SMS or calling)

SOS/Input 1 Active

Report when input1 (SOS) is active/pressed.

Input 2 Active

Report when input 2 is active.

Input 3 Active

Report when input 3 is active.

SOS/Input1 Inactive

Report when input 1 inactive (SOS released).

Input 2 Inactive

Report when input 2 inactive.

Input 3 Inactive

Report when input 3 inactive.

Low Battery

Report when backup battery’s voltage is below 3.5V.

Low External Power

External power (car battery) is lower than predefined voltage.

You can define voltage in Main Settings.

Speeding

Report when MVT600 speeds higher than the pre-set value.

Value can be changed on tap III Main Settings

Enter Geo-fence

Report when MVT600 enters Geo-fence.

Exit Geo-fence

Report when MVT600 exits Geo-fence.

Geo-fence can be changed on tap III Main Settings.

External Power On

Alarm when external power supply is on or recover.

External Power Off

Alarm when external power supply if off or cut.

No GPS Signal

Report when MVT600 enters GPS blind area or no GPS signal.

Get GPS Signal

Report when MVT600 exits GPS blind area or get GPS signal.

Enter Sleep

Report when MVT600 enters sleep mode.

Exit Sleep

Report when MVT600 exits sleep mode.

Sleep mode can be changed on tap III Main Settings.

GPS Antenna Cut

Alarm when the GPS antenna is disconnected or cut

Device Reboot

Report when MV600 is rebooting.

Heartbeat Report

Turn on heartbeat report

You can define heartbeat interval on tap III Main Settings.

Heading Change Report

Auto report when MVT600’s direction changes over predefined angle

You can define angle degree on tap III Main Settings.

Distance Interval Report

Track by distance.

Interval can be changed on tap III Main Settings.

Tow Alarm

Alarm when the tracker trembles for a period of time.

You can define tow time on tap III Main Settings.

Press Input 1 (SOS) to call

Make a call to authorized phone number when press input 1 (SOS).

Press Input 2 to call

Make a call to authorized phone number when press input 2.

- 15 -

UTRACK MVT600 User Guide Version 3.0

Press Input 3 to call

Make a call to authorized phone number when press input 3.

Reject Incoming Call

Hand up automatically incoming call from correspondent authorized

phone number.

Call for SMS Location Report

Reject incoming call or report SMS location when no answer.

Auto Answer Incoming Call

Auto answer the incoming call for conversation

Listen-in (voice monitoring)

Auto answer the incoming call for voice monitoring

6.5.2 GPRS Tracking

Click Tap II: GPRS Tracking

Item

Description

GPRS

Select TCP/UDP to enable GPRS communication.

GPRS Interval

Track by time interval via GPRS.

Set time interval for GPRS tracking.

Interval is in unit of 10 seconds.

Interval = 0, stop tracking by time interval.

Max time interval = 65535*10 seconds

GPRS Report T imes

= 0, report without limit.

= [1,65535], set report times, MVT600 will stop reporting when reaching

- 16 -

UTRACK MVT600 User Guide Version 3.0

the times.

IP & Port

Input s

erver

’s IP address and port number.

Secondary IP and Port

(Backup Server)

Input backup s

erver

’s IP address and port number to avoid data losing

when main server is down. The backup server

will receive data

APN

APN user name

APN password

APN, APN username, APN password: max 32 bytes.

If no username and password required, leave them blank.

Tracker ID

MVT600’s IMEI. It is the only ID in GPRS packet.

Read

Read current tracker’s settings for above items.

Write

Write above settings to the tracker.

T ick the box for receiving GPRS report.

Event Description:

Event

Description

(If the box is ticked, authorized phone number will get event report

by SMS or calling)

SOS/Input 1 Active

Report when input1 (SOS) is active/pressed.

Input 2 Active

Report when input 2 is active.

Input 3 Active

Report when input 3 is active.

SOS/Input1 Inactive

Report when input 1 inactive (SOS released).

Input 2 Inactive

Report when input 2 inactive.

Input 3 Inactive

Report when input 3 inactive.

Low Battery

Report when backup battery’s voltage is below 3.5V.

Low External Power

External power (car battery) is lower than predefined voltage.

You can define voltage in Main Settings.

Speeding

Report when MVT600 speeds higher than the pre-set value.

Value can be changed on tap III Main Settings

Enter Geo-fence

Report when MVT600 enters Geo-fence.

Exit Geo-fence

Report when MVT600 exits Geo-fence.

Geo-fence can be changed on tap III Main Settings.

External Power On

Alarm when external power supply is on or recover.

External Power Off

Alarm when external power supply if off or cut.

No GPS Signal

Report when MVT600 enters GPS blind area or no GPS signal.

Get GPS Signal

Report when MVT600 exits GPS blind area or get GPS signal.

Enter Sleep

Report when MVT600 enters sleep mode.

Exit Sleep

Report when MVT600 exits sleep mode.

Sleep mode can be changed on tap III Main Settings.

GPS Antenna Cut

Alarm when the GPS antenna is disconnected or cut

Device Reboot

Report when MV600 is rebooting.

- 17 -

UTRACK MVT600 User Guide Version 3.0

Heartbeat Report

Turn on heartbeat report

You can define heartbeat interval on tap III Main Settings.

Heading Change Report

Auto report when MVT600’s direction changes over predefined angle

You can define angle degree on tap III Main Settings.

Distance Interval Report

Track by distance.

Interval can be changed on tap III Main Settings.

Tow Alarm

Alarm when the tracker trembles for a period of time.

You can define tow time on tap III Main Settings.

RFID

RFID data.

For more information about GPRS settings, please refer to SMS/GPRS Protocol.

7

Installation

7.1 Install I/O Cable

The I/O cable is a 12-pin cable including power, analog input, negative/positive input and output.

I/O

1

Power

(+)

3

Input 3

5

Input 2

7

Output 1

9

Output 2

11

Output 3

2

GN

D(-)

4

Input 1 (-)

6

GN

D(-)

8

AD Input 1

10

AD Input 2

12

AD Input 3

PIN Number

Color

Description

1 (Power)

Red

DC In (power source). Input voltage: 9V~36V. 12V suggested

2 (GND)

Black

Ground

3 (IN3)

White

Digital Input3. Positive triggering, for detecting status of vehicle door or ACC.

4 (IN1)

White

Digital Input1. Negative triggering( Defaulted as SOS Panic Button)

5 (IN2)

White

Digital Input2. Negative triggering, for detecting status of vehicle door.

6 (GND)

Black

Ground. It can be used to connect with temperature/fuel sensor etc.

7 (OUT1)

Yellow

Output1. It can be used to connect with relay for engine immobilization.

Low voltage (0V) when effective and open drain when ineffective.

Output open drain sink voltage (ineffective): 45V max.

- 18 -

UTRACK MVT600 User Guide Version 3.0

Output low voltage sink current (effective): 500mA max

8 (AD1)

Blue

12 Bits Resolution Analog Input1. 0~6V DC Detection. It can be used to connect

with temperature/fuel sensor etc.

9 (OUT2)

Yellow

Output2. It can be used to connect with relay for engine immobilization.

Low voltage (0V) when effective and open drain when ineff

ectiv

e. Output

open drain sink voltage (ineffective): 45V max.

Output low voltage sink current (effective): 500mA max.

10 (AD2)

Blue

12 Bits Resolution Analog Input2. 0~6V DC Detection. It can be used to connect

with temperature/fuel sensor etc.

11 (OUT3)

Yellow

Output3. It can be used to connect with relay for engine immobilization.

Low voltage (0V) when effective and open drain when ineff

ective

. Output

open drain sink voltage (ineffective): 45V max.

Output low voltage sink current (effective): 500mA max.

12 (AD3)

Blue

12 Bits Resolution Analog Input3. 0~6V DC Detection. It can be used to connect

with relay for engine immobilization.

Power/GND (PIN1/PIN2)

Connect GND (-Black) and Power (+Red) wires to the battery of vehicle.

7.1.2 Digital Input (PIN4/5, negative triggering)

7.1.3 Digital Input (PIN3, positive triggering)

- 19 -

UTRACK MVT600 User Guide Version 3.0

7.1.4 Output

7.1.5 Analog Input

7.1.5.1 Analog Input Application 1– Detect External Power Voltage

Input range：0-6V

Voltage Caculating Formula: input voltage=(AD*3.3*2)/4096

0x0C9B=>3227(decimal)=>(3227*3.3*2)/4096=5.1997V(voltage)

0x0D9D=>3845(decimal)=>(3845*3.3*2)/4096=5.6154V(voltage)

7.1.5.2 Analog Input Application 2 – Fuel Detection (percentage of fuel)

Note:

Fuel level sensors supplied by us are resistance-type sensors with output resistance: 0-200Ω (ohm).

For the circuit shown on above figure, if VCC is 12V, R should be 200Ω (ohm) and if VCC is 24V then R should

be 600Ω (ohm) to make the input range to AD1 or AD2 is 0-6V.

Below formula is for calculating the fuel percentage left for this fuel level sensor:

1.1*AD value

Percentage Left =

* 100%

4096 X 2 – 1.1*AD value

The value must be converted into decimal, for example, 0x0313 is 787 in decimal, the results is 11.82%.

- 20 -

UTRACK MVT600 User Guide Version 3.0

7.1.6 Install Handset Phone (RS232 Interface)

PIN Number

Color

Description

1

Red

Power Output. Output Voltage: 5V

2

Black

Ground

3

White

Handset Phone RS232 TX (MVT600 RX)

4

Yellow

Handset Phone RS232 RX (MVT600 TX)

5

Orange

Microphone Positive

6

Grey

Microphone Negative

7

Purple

Speaker Positive

8

Brown

Speaker Negative

Note: This interface also supports LCD display; navigator provided conforms to SMS Protocol.

7.1.7 Install Camera (RS232 Interface)

Camera1 RS232 Interface

PIN Number

Color

Description

1

Red

Power Output. Output Voltage: 5V

2

Black

Ground

3

Yellow

Camera RS232 TX (MVT600 RX)

4

Green

Camera RS232 RX (MVT600 TX)

Camera2 RS232 Interface

PIN Number

Color

Description

1

Red

Power Output. Output Voltage: 5V

2

Black

Ground

3

Yellow

Camera RS232 TX (MVT600 RX)

4

Green

Camera RS232 RX (MVT600 TX)

- 21 -

UTRACK MVT600 User Guide Version 3.0

GPS RS232 Data Interface

PIN Number

Color(Suggested)

Description

1

Red

Power Output. Output Voltage: 5V

2

Black

Ground

3

Yellow

RS232 Interface TX (MVT600 RX)

4

Green

RS232 Interface RX (MVT600 TX)

Note: Micro SD is required for taking photos.

7.1.8 Install Micro SD

There’s a Micro SD card slot under the On/Off button. Micro SD card can be used to store the pictures taken by

the camera.

7.1.9 Install RFID Reader (W iegand Interface)

PIN Number

Color

Description

1

Red

Power Output. Output Voltage: 5V

2

Black

Ground

3

Green

RFID Data0

4

Yellow

RFID Data1

7.2 Install GPS/GSM Antennas

GPS Antenna GSM Antenna

Connect the GSM antenna to the SMA connector which is ‘GSM’ text labeled. The GSM antenna is non-directional,

so you can hide it in any place of vehicle.

UTRACK MS02 User Guide version 1.3

- 22 -

Connect GPS antenna to the GPS connector which is ‘GPS’ labeled. The optimum location for the GPS antenna

is on the roof of the vehicle. The covert and GPS antenna are directional, make sure they are facing up and

lying as flat as possible. Secure them in place with glue or zip ties.

Note: Do not shield or cover the GPS antenna with any objects containing

metal.

7.3 Mount the MVT600 unit

If mounting required, there are 4 screw holes on the MVT600, 2 along either side that act as fixing points to

the vehicle

Please do not hesitate to email us at support@extramiles.asia if you have any questions.

Extra Miles UTRACK MVT600 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual