EXTRA Computer Pokini F2 User Manual

F2

manual

English

2

The contents were created with special care. However, no liability can be as­sumed for errors that are still present and their effects. We will gladly take up
and implement recommendations for the improvement of this manual.

All rights reserved. Any use of extracts in any form (digital or print) must be
approved in writing by EXTRA Computer GmbH.

Pokini is a registered trademark of EXTRA Computer GmbH and is subject to
copyright protection.

This user guide has been prepared and published by:

EXTRA Computer GmbH
Brühlstraße 12
89537 Giengen

phone:
fax:
mail:

07322 / 96 15 - 0
07322 / 96 15 - 290
[e-mail]

3

F2

Instructions

Safety instructions
Warrenties
Disposal of old equipment
CE marking

Unpacking and installation

Introduction

1.1 Package contents

 1.2Hardwarespecications

1.3 Features

Quick start guide

2.1 Connecting Pokini F

2.3 Booting Windows

Service

3.1 Access to storage, SIM, miniPCIe and battery

3.2 To access RAM

BIOS

Drivers

Support

4

4

6

6

7

8

10

10

11

13

15

16

12

12

13

4

Safety instructions

Please note the following safety instructions before using your new system:

The socket, to which your PC is connected, should be protected
with a maximum of 16A in the electro-installation. ATTENTION!
Your computer contains a lithium battery. Incorrect replacement of
the battery may result in a risk of explosion. Replacement only by
the same, or a equivalent type recommended by the manufactur­er. Please do not dispose of used batteries over household waste.
Use the service of specialized stores that carry out the exchange.

Never use the PC in a damp environment or near water.

IP protection class: IP30
Protected against solid foreign bodies
with a diameter of 2.5 mm or more.

Do not place the PC near a high heat source.
The ambient temperatures:

in operation -40°C to +70°C

out of operation, storage -40°C to +70°C

5

F2

If you want to clean the system, do not use liquid cleaners or clean­ing sprays. The cleaning is best done with a damp cloth.

During transport, the system should be packaged in a shock-proof
package. The original packaging offers the most ideal conditions.

Repairs may only be carried out by qualified personnel.

The mains plug serves as a disconnect point to the supply network
(220V). Therefore the socket should be close to the system (max.

1.5 m) and easily accessible. It is recommended to use a socket
strip with overvoltage protection Peripheral devices. Please do not
place any objects on the power cord and lay it over.

6

Warranties

Disposal of old equipment

The warranty agreement of the BGB applies to all systems. The system you

purchased was produced in our ISO 9001 certied company in an environmentally
sound and quality environment.

All systems and the components installed therein are mainly made of recyclable
materials. At the end of the life cycle, the system is taken back and properly

recycled or disposed of. To return a device, please use the recycling and disposal
facilities available in your country.

We have contractually committed all manufacturers and suppliers to deliver to us
only products that comply with the currently valid laws. This applies in particu­lar to the two EU directives WEEE and RoHs. Since not every manufacturer can
register in Germany beyond the national boundaries, EXTRA Computer GmbH has
assumed the responsibility for the disposal in cases and registered with the EAR.
EXTRA Computer GmbH is located at the EAR (Waste electrical register)
The following number: WEEE Reg. DE 57965674

This ensures that our products are registered according to the specifications and

comply with the current laws. For you as a customer of EXTRA
Computer GmbH does not incur any additional costs for distribution in Germany,

unless you yourself are a manufacturer in the sense of the ElektroG.

For further information on the ElektroG you can find here:

www.stiftung-ear.de

Under Q&A you will find sorted by keywords the latest information.

7

F2

CE marking

This device complies with the requirements of the
EG Directives:

2014/30/EU „Electromagnetic Compatibility“,

2014/35/EU „Low Voltage Directive“,
2009/125/EC „Ecodesign Directive“ and
2011/65/EU „RoHs Directive“.

CE marking for devices with radio components

This device complies with the requirements of EC Directive 1999/5/EC of the
European Parliament and of the Council of 9 March 1999 on radio equipment and
telecommunications equipment and the mutual recognition of conformity.

This equipment may be used in the following countries:

Belgium Bulgaria Denmark Germany Estonia
Finland France Greece Great Britain Ireland
Iceland Italy Latvia Liechtenstein Lithuania
Luxembourg Malta Netherlands Norway Cyprus
Poland Portugal Romania Sweden Switzerland
Slovakia Slovenia Spain Czech Republic

Hungary Austria

You can nd up-to-date information about possible restrictions on the operation at
the appropriate authority in the respective country. If your country is not listed in the
list, please check with the relevant supervisory authority to determine whether the

use of this product is permitted in your country.

8

Unpacking and installation

■

Check the contents of the package for any transport damage

■

Match the delivery with your purchase order

In the case of transport damage, faulty deliveries or questions, please contact your

local Pokini dealer immediately. The original packaging of the equipment should be
kept for transport.

Disposal packaging material

The packaging carton and all cardboard parts can be disposed of the waste paper.

The PE foam parts (transport protection of the computer) can be fed to the yellow
sack* (*e.g. in germany) or other plastic recycling.

Position the system

■

Lay the cables so that they do not create a hazard (danger of tripping) and are

not damaged.

■

DANGER: In order to avoid the risk of electric shock, this device may only be

connected to a power supply with protective conductor.

■

ATTENTION: Your computer contains a lithium battery. Incorrect replacement of

the battery may result in a risk of explosion. Replacement only by the same or
a equivalent type recommended by the manufacturer. Please do not dispose of
used batteries over household waste. Use the service of specialized stores that

carry out the exchange.

■

In case of emergency (eg damage to the housing, controls or power supply, if

liquids or foreign bodies are penetrated) switch off the device immediately, dis-

connect the mains plug and inform your dealer or system partner.

9

F2

■

The device is not waterproof! Never immerse the appliance in the water and

protect it from splashing water (rain, sea water).

■

The intended operation of the device is guaranteed only with a fully assembled

housing and built-in covers for installation areas (electrical shock, cooling, re
protection, interference suppression).

■

When using an extension cable or a power strip, make sure that the extension

cable or the power strip is suitable for the product. If you have any questions,

please contact your dealer or system partner.

■

Use accessories supplied with the device or component.

10

1. Pokini F2 computer

2. 12V DC power supply

3. Power cord with EU & UK adapter

4. HDMI – DVI adapter

5. WiFi-antennas (in Pokini WLAN models)

6. 3.5 mm to RCA cable

7. Mini-serial to DB-9 adapter cable

To use Pokini, you need:

■

A display with miniDP- or HDMI-input and a miniDP / HDMI cable

■

USB keyboard and mouse

2

3

4

7

1

5

6

Introduction

1.1 Package contents

11

F2

1.2 Hardware specifi cations

Hardware

CPU Intel Apollo Lake (Atom | Celeron | Pentium)

Dual-core or quad-core

Memory 1x SO-DIMM 204-pin DDR3L SDRAM

Bis zu 16GB Non-ECC DDR3L-1866 (1.35V)

Storage 1x M.2 M-key 2242 | 2260

Optional eMMC
Optional 2.5” HDD | SSD

Display & Graphics HDMI 1.4b up to 3840 x 2160 @ 30Hz

DisplayPort 1.2 up to 4096 x 2160 @ 60 Hz
(via Mini DP connector)

Audio Realtek ALC1150 HD audio codec

Analog stereo output | Digital 7.1 channels S/
PDIF output (3.5mm)
Analog stereo microfon input (3.5mm)

Networking 2x Intel I211 GbE controller (RJ-45)

WLAN 1x M.2 E-key 2230 slot (optional)

USB 2x USB 3.0, 2x USB 2.0
Serial 1x Sserial connector

COM1: RS232 via mini serial connector

SD ­Others FACET rev 2 connector

(PCIe x2, USB2.0, eDP1.3, I2S, I2C, UART)

12

case 100% Aluminium / im Druckgussverfahren

hergestellt

measurement 112 mm x 84 mm x 34 mm
weight 350g

operating temperature -40°C - 70°C

power supply 12V Netzteil
power consumption Im Idle Modus (S0): 5 - 15 Watt

BIOS ? (Phoenix BIOS

Unterstützte Bootmedien: USB thumb drive,
USB hard disk, Netzwerk)

OS Windows 10

Linux

(andere Betriebssysteme können durch den Anwender installiert
werden)

Operating Conditions

Software

13

F2

2x USB 2.0 HDMI

2x USB 3.0

Power 2x GB LAN

miniDP

Audio Micro SD

RS232

USB

Pokini F has 2x USB 3.0 and 3x USB 2.0 Ports.

Serial port

RS232 mini-serial ports located on the back panel. Mini-serial to DB9 cable to
connect to standard serial devices is supplied in the package

1.3 Features

14

Videosignal

The Pokini F2 has 1 HDMI connector and 1 mini-DP connector inclusive
audio-support.

Using an HDMI-to-DVI cable to run an DVI-display with the Pokini F2.

Using an miniDP-to-DP cable to run an DisplayPort-display with the Pokini
F2.

Audio

There are 2 standard 3.5mm jacks on the front panel:

Left: ■ Stereo line-in

■ SPDIF in using provided cable

Right: ■ Stereo line-out

■ SPDIF out using provided cable

LAN

Pokini F2 features a two or four 10/100/1000 Base-T LAN ports with
RJ45-connectors. The LAN ports have integrated LED-lamps, which shows
the connection status. Pokini F2 supports PXE-Boot and Wake-on-LAN.

WLAN

Pokini F2 features a internal 802.11ac WiFi module with two antennas.

Power-Button

Pokini F has a tactile power push-button. It is used for turning on/off the PC
and for standby/resume when supported by the operating system. A push
of at least 5 seconds will always turn off the Pokini.

15

F2

■ Turn off the display and connect it to the Pokini HDMI connector
(use the HDMI to DVI adapter if needed).

■ Connect the USB keyboard and mouse to USB ports.

■ Plug the speakers in the line-out connector.

■ Plug the Ethernet cable into the Ethernet connector.

■ OnlyPokiniF2WLAN:MountWiantennasonSMAconnectorsby

 turningitclockwiserepeatedlyuntiltheantennaholdsrm.

■ Firmly Insert the DC plug into the Pokini F DC-in jack (1). Rotate
plug clockwise 90° to secure (2).

■ Connect the power supply to the AC cord and plug the cord into
AC outlet.

1

2

Quick start guide

2.1 Connecting Pokini F

16

Uponrstpower-up,youwillbeguidedthroughtheWindowsWelcome

procedure which is selfexplanatory.

Pokini F has no moving parts and requires no maintenance.
The following operations could be done by the user.

Open the bottom cover by un­screwing 4 philips-head screws.

Now Side panels and cover can be
removed.

2.2 Booting Windows (for Pokini with Windows pre-installed)

3.1 Access to storage, SIM, miniPCIe and battery

Service

17

F2

The M.2 SSD and the mi­ni-PCIe interface are located
on the M.2 cooling plate.
Loosen the three screws
of the cooling plate and
carefully pull the M.2 SSD
including the cooling plate
out of the interface.

The RAM is located under
the top cover of the Pokini
F2.

Re-assemble in reverse
order.

3.2 To access SSD

3.3 To access RAM

18

Turn off Pokini F. Turn on while holding down the Del key.

Drivers

Alldriverscanbendhere:

www.pokini.de → Produkte → Pokini F2 → Downloads

Support

BIOS

Please feel free to contact us via E-Mail:

[e-mail]

You have technical questions?

Entering BIOS Setup Utility

19

F2

All rights reserved. © 2017 EXTRA Computer GmbH

V 1.0 / 12-2017 Art.-No.: 105078