User Manual
Two-Way
Articulating Probe
Model HDV7C-A2-45-15. For use with
HDV700 VideoScope.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
CAUTION
• Do not insert the probe into flammable liquid or gas.
• Before inspecting a vehicle, shut off the engine. Allow the metal and liquids
in the vehicle to cool before inspection.
• This product is designed for industrial use only. It is not intended for use in
human or other biological inspection.
• Do not disassemble the product, damage to the product and electrical
shock may occur.
• Do not allow the camera head to come in contact with acidic, corrosive or
heated material, serious damage to the equipment can occur.
Introduction
Thank you for selecting the Extech two-way articulation camera
probe. The probe is intended for use with the HDV700 VideoScope.
Obtain the HDV700 user manual and additional translations of this
user manual on the support site
Safety
Please read and understand all safety cautions before use.
#NAS100126; r. AB/87923/87926; en-US
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
1
Product Description
1. Probe to guide camera head to inspection area.
2. Articulating probe neck.
3. Camera head with worklights.
4. Articulation control dial.
5. Image enhancement button.
6. Rotation button (90°) with red LED
7. Switch to lock/unlock buttons (5) and (6).
8. Connecting cable.
9. HDV700 connector.
#NAS100126; r. AB/87923/87926; en-US
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
2
Connecting the Probe
1. Align the white dot on the probe connector with the white dot on
the monitor connector.
2. Plug the probe into the monitor unit, ensuring proper alignment
and full insertion.
3. Tighten the collar nut to secure the connection. Do not
overtighten.
CAUTION
Do not use excessive force when turning the control dial, damage to the camera probe can result. Do not attempt to force the flexible neck past its maximum angle. Stop turning the control dial when the maximum angle is reached.
For safety and ease of use, straighten the neck before inserting and
removing the probe from the inspection area.
The steps below explain how to safely connect the probe to the
HDV700 monitor. Always turn the HDV700 power off before replacing the probe.
Operation
Controlling Articulation
Turn the control dial (4) clockwise to bend the probe neck to the
right; turn the dial counter-clockwise to bend the neck to the left, as
shown in the image below. The articulation range is 180° maximum,
do not attempt to force the control dial past the bend limit.
#NAS100126; r. AB/87923/87926; en-US
3
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Image Enhancement Button
to add clarity to darker
areas of the camera image.
to rotate the image 90°. The button’s
red LED is on when an image is rotated and off when rotation is not
applied.
Use the image enhancement button (5)
Rotation Button
Use the rotation button (6)
Button Lock
To lock/unlock the control buttons, move the locking switch (7) to
the right to lock the buttons or move the switch to the left to release
the lock.
Measurement Considerations
• The probe contains small circuitry that controls the optics and
electronics of the camera. To ensure reliability, do not bend the
probe more than 90°.
• Do not coil the probe < 6 in. (15 cm) in diameter in use.
• To avoid camera damage, please straighten the neck before removing it from the inspection area. Failure to do so may cause
the camera to become stuck in the inspection area.
• The neck, near tip of the probe, is particularly sensitive to excessive force. Never bend the neck by hand; use only the control
dial.
• Please keep the probe’s alignment as straight as possible while
in use.
• Do not force the control dial when resistance to movement is felt;
Damage to the camera can result.
• Do not allow the probe to forcefully impact an object.
• Do not put excessive weight on any area of the probe.
• Never use the probe as a hammer, hook, or other tool.
• Never use the probe tip to clear pathways or to unclog a pipe.
Storage and Maintenance
• To clean the probe, wipe with a soft cloth dampened with a mild
detergent and clean water. Do not use abrasive detergents. Do
not use corrosives or solvents to clean the probe. Use a high
quality lens cleaning fluid and a lint-free swab to clean the camera and worklight lenses.
#NAS100126; r. AB/87923/87926; en-US
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
4
• To protect the camera, keep the lens cap, and other supplied
protective coverings, attached when not in use. Store in the original case.
• Straighten the neck angle before placing in storage.
• Avoid direct sun exposure. Store in a cool, dry, and well-ventilated area.
• Do not coil the probe < 6 in. (15 cm) in diameter when storing,
damage to the probe may result.
Specifications
Camera resolution 640(H) x 480(V) pixels
Frame rate 30 frames per second (fps)
Probe diameter 0.15 in. (3.9 mm)
Probe head diameter 0.2 in. (4.5 mm)
Probe head length 0.5 in. (14 mm)
Probe length 4.9 ft. (1.5 m)
Articulation angle 180° maximum (the angle may decrease if
Probe head material
Probe body material Braided mesh stainless steel
Worklights Five (5) LED lamps
Field of View (FOV)
Depth of Field (DOF) 0.4 to 4.0 in. (1 to 10 cm)
Operating and Storage
temperature
Liquids approved for probe
submersion
Ingress protection Probe tip and body: IP 67 (IEC 60529)
the probe is looped)
Stainless steel
90°
14℉ to 140℉ (–10℃ to 60℃)
Brake and transmission fluid, diesel fuel, unleaded gasoline, engine oil, and CPC hydraulic oil (46AWS)
Protected from submersion in water up to 3.3
ft (1 m) for 30 minutes maximum. In use: rain,
splashes, and accidental submersion
#NAS100126; r. AB/87923/87926; en-US
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
5
Two-Year Warranty
FLIR Systems, Inc. warrants this Extech brand instrument to
be free of defects in parts and workmanship for two years from
date of shipment (a six-month limited warranty applies to sensors
and cables).
#NAS100126; r. AB/87923/87926; en-US
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
6
Loading...