User’s Guide
Digital Stopwatch
Model 365535
365535-en-GB_V1.2 1/15
Instructions
Introduction
You are about to enjoy an advanced Cumulative and Lap memory professional digital quartz stopwatch
with advanced timing features.
General Features
-4 buttons operation
-Large LCD display with contrast adjustment
-12/24 hour display
-Normal time and chime
-Daily alarm
-Full 1/100 second chronograph with working range from 0 to 19 hr. 59 min. 59.99 seconds with 500 memory
records of split and lap time.
-Recall function for recorded split and lap times
-Count-Down timer with working range from 0 to 1 9hr. 59min. 59.9 seconds
-Three operating modes (Countdown Repeat, Countdown Stop, Countdown then count up) for countdown timer
-Stroke measurement basing on "3"
-Decimal second, minute and hour chronograph
-Segmented run memory
-Beep sound selectable
-Low battery check
-Accuracy of +/- 5 seconds per 24 hours
Important Note:
This stopwatch can store up to 500 split/ lap times. When there are 5 free memories remain ing,
the “FULL” icon will blink to indicate the nearly full situation. Whenever the storage is full, extra split/lap times will
NOT be stored into memory even if the stopwatch is reset and a new event is started. Extra split/lap times will be
displayed, but not recorded. In order for the stopwatch to record again, the data in memory must be deleted. Please
refer to the “Data Mode” section in this guide to learn how to delete memory
3
365535-en-GB_V1.2 1/15
As you choose each "mode", a message will be displayed for a second before you enter the mode:
Normal Time mode Timer Mode
Alarm Time mode Pace r mode
Chronograph mode Stroke Measurement
Lap Time Recall mode
Data mode
The operation of the stopwatch is divided into eight modes (as noted above):
1. Normal time mode
2. Alarm time mode
3. Ch ronograph and Recall mode
4. Data mode (300M & 500M Models only)
5. Count-down timer mode
6. Pacer mode
7. Stroke measurement mode
Button Operation
- Mode - used to change the mode of the watch
- Start! Stop! Set - used to start and stop the timer counting or the chronograph function
- Recall - used for recalling recorded split and lap times
- Lap! Split! Reset! Select - for taking the record of the split and lap time
TIME
ALARM
CHRONO
RECALL
DATA
TIMER
PACER
STROKE
4
365535-en-GB_V1.2 1/15
This is only a brief description of these buttons. Detailed uses of the buttons are different in particular functions and will be
described later in the instructions.
Pressing [MODE] button will toggle among the m odes above. Note that there is no auto-return function in the sto pwatch. Whenever
you change modes, the stopwatch will remain in that mode until the [MODE] button is presse d again
Each time you enter a mode, a message will be displayed for a second before you enter the mode:
Note:- In the following descriptions, items printed in dark gray stand for flashing digits.
NormalTime Mode
The starting point for operating your stopwatch is NORMALTIME. If NORMALTIME is not displayed, press [Mode] until it is.
Year:- 2001
Date : - January 1
Dayof week:- Monday Time: 12:00 am
The display format is as below :-
During clock display, press [START] to switch between 12Hr and 24Hr display mode. To toggle chime ON or OFF, you can press
[RESET]. The bell icon will be ON and OFF correspondingly.
Normal Time Setting
Press and hold [RECALL] for 2 seconds to enter setting mode. The normal time setting starts with second. T he second digits will
then be flashing.You can change the flashing digit by pressing [START] button. To speed up the setting you can press and hold
[START] for longer than 2 seconds to activate fast setting. To select other digits, press [RESET] button. The setting order is:
Second, Minute, Hour, Year, Month, Date, month-date (m-d)
year
day, month - date
hr: min second
2001
WE 1-3
A 10:35’30
5
365535-en-GB_V1.2 1/15
or date-month (d-m), Sound ON or OFF, Contrast (darkness of the digits - default is 9), then back to Second, and
recycles again. Note: when the second is to be set, press [START] to reset the second digits to zero.
At the end of setting, press [RECALL] or [MODE] to exit from the setting mode and back to Normal Time
Display.
Display for Sound ON or OFF setting :
(Let the current status be "ON".)
Press [START] to toggle Sound ON or OFF
Display for contrast adjustment:-
(Let the current contrast be "5")
Press [START] consecut ively to advance
the contrast up to 16, then cycle back to 1.
The contrast setting will be shown on
the display.
NOTE:
-The hour digits may be displayed in 12hr or 24h r format.
-The year digits can be set from 2000 to 2099. The date adjusts automatically for odd and even months
including February of leap years. The day of week also adjusts automatically after you set the date.
SOUnd
On
SOUnd
On
COnT
5
COnT
16
Loading...