EXSYS EX-41384 Instructions

Anleitung
Vers. 1.0 / 01.10.15
RS-232 PCI Karte
mit 4 x 9 Pin Anschluss
EX-41384
Manual
EX-41384
Inhaltsverzeichnis
1. Beschreibung ······················································································ 3
2. Lieferumfang ······················································································ 3
3. Aufbau und Anschlüsse ······································································ 4-5
3.1 Aufbau······································································································ 4
3.2 Anschlüsse ······························································································ 4-5
4. Jumper Einstellungen ········································································· 5-6
5. Hardware Installation ············································································ 6
6. Treiber Installation ············································································· 7-8
7. Technische Daten ················································································ 8
Index
1. Description ························································································· 9
2. Extent of Delivery ················································································ 9
3. Layout and Connections ·································································· 10-11
3.1 Layout ····································································································· 10
3.2 Connections ························································································ 10-11
4. Jumper Settings ············································································ 11-12
5. Hardware Installation ··········································································· 12
6. Driver Installation ··········································································· 13-14
7. Technical Information ·········································································· 14
EX-41384 Deutsch
Die EX-41384 ist eine PCI serielle RS-232 Karte mit 4 seriellen FIFO 16C95x Ports, für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B. Terminal, Modem, Plotter usw.). Der serielle PCI Bus unterstützt dabei optimal die Leistung des schnellen SystemBase Chipset mit 256byte FIFO Cache. Die EX-41384 gewährleistet so eine sichere Datenübertragung und exzellente Performance von bis zu 921KBaud/s für jedes angeschlossene Gerät! Sie unterstützt den 32-Bit PCI & PCI-X Bus mit 5 Volt und 3,3 Volt. Es ist nicht möglich die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim installieren des Betriebs-
systems automatisch vorgenommen werden. Über die Jumper können Sie 12V oder 5V
auf Pin9 des seriellen Anschluss umleiten. Achten Sie bitte darauf dass die Ange­schlossenen Geräte dies auch unterstützen. Des weiteren können Sie über einen ande­ren Jumper die Spannung von +5V oder +3,3V auf den UART einstellen. Es wird zu­sätzlich für den Einbau in schmale Computergehäuse ein 8 cm LowProfile Slot-Bügel mitgeliefert.
Merkmale:
Kompatibel zu PCI und PCI-X Bus Bis 921.6 Kbps Baud Rate Unterstützt wird RS-232 Unterstützt Windows NT 4.0/ 9x/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux
Zertifiziert für CE / FCC / RoHS / WEEE DE97424562
Bevor Sie die EX-41384 in Ihren PC installieren, überprüfen Sie bitte zuerst den Inhalt der Lieferung:
EX-41384
Treiber CD
Bedienungsanleitung
Octopus Kabel
Low Profile Bügel
1. Beschreibung
2. Lieferumfang
Deutsch EX-41384
3.1 Aufbau
3.2 Anschlüsse
3. Aufbau und Anschlüsse
S1-S4:
44 Pin Buchse für Octopus-Kabel mit 4 x 9 Pin Serielle Anschlüsse
J3-J6:
Interne Anschlüsse
S1_PWR-S4_PWR:
Power auf 9 Pin Stecker Ein/Aus
JP1: Jumper zum einstellen der Spannung am UART
JP2: Jumper für die
Stromquelle (Netzteil oder
J2: Str oman­schluss
JP4: Nur für Testzwecke (Bitte nicht ändern)
JP3: PME Ein-/ Ausschal- ten
DB9 (EX-41384) DB9 (Endgerät)
1 DCD 1 DCD
2 RXD 2 RXD
3 TXD 3 TXD 4 DTR 4 DTR 5 GND 5 GND 6 DSR 6 DSR 7 RTS 7 RTS 8 CTS 8 CTS
1
2
3
4
SystemBase Chipset
S1-S4:
EX-41384 Deutsch
4. Jumper Einstellungen
3. Aufbau und Anschlüsse
3.2 Anschlüsse
1 +5V 2 GND 3 GND 4 +12V
Für X5V oder X12V Einstellung (JP2) muss J2 mit dem PC Netzteil verbunden werden! Sonst wird die Karte nicht mit Strom versorgt.
JP1:
+3.3V = Der Spannungspegel wird auf 3.3V gesetzt. (Werkseinstellung)
+5V = Der Spannungspegel wird auf 5V gesetzt.
Benötigt Ihr Endgerät einen höheren Spannungspegel, so setzen Sie den Jumper auf +5V.
Wenn Sie die Jumper S1_PWR-S4_PWR für auf PWR gesetzt haben, können Sie mit dem Jumper JP2 die Spannungsquelle einstellen. Es gibt 2 verschiedene Spannungsquellen (Mainboard & PC-Netzteil).
(Bei Jumper Einstellung X5V / X12V muss der Stromanschluss (J2) mit
dem PC-Netzteil verbunden werden!)
I5V = 5Volt vom Mainboard (STANDARD) X5V = 5Volt vom PC-Netzteil X12V = 12Volt vom PC-Netzteil I12V = 12Volt vom Mainboard (STANDARD)
I5V
X5V
X12V I12V
JP2:
+5V +3.3V
ENA | DIS
JP3:
DIS = Die Funktion PME ist ausgeschaltet. (Werkseinstellung)
ENA = Die Funktion PME ist eingeschaltet. Der PC kann nun durch
die Seriellen Ports der EX-41384 aktiviert werden.
Dieser sollte aber bei Standard Anwendungen nicht verstellt werden.
J2:
Deutsch EX-41384
4. Jumper Einstellungen
12V 5V DIS
S1_PWR-S4_PWR:
DIS = Am Pin 9 liegt das Standard Signal RI (Ring Indicator) an.
(Werkseinstellung)
5V = Am Pin 9 liegt jetzt eine Spannung von +5V an. 12V = Am Pin 9 liegt jetzt eine Spannung von +12V an.
Es gibt den Jumper vier mal auf der Platine, sodass Sie für alle seriellen Ports die Einstellung individuell vornehmen können. Die Einstellung der Spannungsquelle nehmen Sie mit JP2 vor. Dieser sollte aber bei Standard
Anwendungen nicht verstellt werden.
5. Hardware Installation
Wenn Sie die Karte installieren, beachten Sie bitte die folgenden Hinweise. Da es große Unterschiede zwischen PC‘s gibt, können wir Ihnen nur eine generelle Anleitung zum Einbau der EX-41384 geben. Bei Unklarheiten halten Sie sich bitte an die Bedienungsan­leitung Ihres Computersystems.
1. Schalten Sie Ihren Rechner und alle angeschlossenen Peripheriegeräte aus und zie-
hen Sie bei allen Geräten den Netzstecker.
2. Lösen Sie die Schrauben des Gehäuses auf der Rückseite Ihres Computers und ent- fernen Sie vorsichtig das Gehäuse.
3. Suchen Sie einen freien PCI Steckplatz und stecken Sie die Karte vorsichtig in den ausgewählten PCI Steckplatz ein. Stellen Sie sicher das es sich um den richtigen Steckplatz handelt!
4. Beachten Sie das die Karte korrekt eingesteckt wird und das kein Kurzschluss ent- steht. Wenden Sie bitte keine Gewalt an um die Karte einzustecken!
5. Danach befestigen Sie die Karte bitte mit einer Schraube am Gehäuse.
6. Jetzt können Sie das Computergehäuse mit den Schrauben wieder schließen.
EX-41384 Deutsch
6. Treiber Installation
Windows 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx
Windows erkennt beim Start einen neuen “PCI Controller“ und öffnet automatisch den Windows Hardwareassistenten. Wählen Sie die manuelle Installation aus und legen Sie die Treiber CD in Ihr CD-ROM Laufwerk (z.B. Laufwerk D:). Geben Sie nun den Pfad "D:\IO\SYSTEMBASE\DRIVER\PCI" und dann das Verzeichnis Ihres Betriebssys­tems “32bit_Win10_8.x_7_Vista_XP_20xx“ oder “64bit_Win10_8.x_7_Vista_XP_20xx” in das jeweilige Feld für die Quelle/Pfad ein und klicken Sie auf >weiter<. Windows sucht jetzt die Treiber in dem angegebenen
Verzeichnis. Folgen Sie den Anweisungen des Hardwareassistenten und beenden Sie
die Installation. Sollte Windows noch weitere neue Hardware erkennen, wiederholen Sie die oben angegebenen Schritte. Wichtig! Starten Sie Ihren PC in jedem Fall nach der Installation neu.
ÜBERPRÜFEN DER INSTALLIERTEN TREIBER Öffnen Sie nun den >GeräteManager<. Dort müssten Sie unter "Anschlüsse (COM und
LPT)" mehrere neue “PCI Ports“ z.B. (Com3) sehen. Wenn Sie diese oder ähnli­che Einträge sehen, ist die Karte korrekt installiert.
ÄNDERN DER PORT NUMMER
Wenn Sie die Portnummer ändern möchten, klicken Sie z.B. auf >COM3<
>Anschlusseinstellung< und >Erweitert<. Sie können dann zwischen COM3 und COM256 wählen!
Windows 9x
Starten Sie Windows 9x und legen Sie die Treiber CD in Ihr CD-ROM Laufwerk (z.B. Laufwerk D:) und klicken Sie auf >Start< >Ausführen< und geben Sie „D:\IO\SYSTEMBASE\DRIVERS\PCI\Win9x\INSTALL.exe" ein. Windows 9x startet das Setup Programm und installiert den Treiber. Wichtig! Starten Sie Ihren PC in jedem Fall nach der Installation neu.
ÜBERPRÜFEN DER INSTALLIERTEN TREIBER Öffnen Sie nun den >GeräteManager<. Dort müssten Sie unter "Anschlüsse (COM und
LPT)" mehrere neue “PCI Ports“ z.B. (Com3) sehen. Wenn Sie diese oder ähnli­che Einträge sehen, ist die Karte korrekt installiert.
Windows NT 4.0
Starten Sie Windows NT 4.0 und legen Sie die Treiber CD in Ihr CD-ROM Laufwerk (z.B. Laufwerk D:) und klicken Sie auf >Start< >Ausführen< und geben Sie „D:\IO\SYSTEMBASE\DRIVERS\PCI\WinNT\INSTALL.exe" ein. Windows NT 4.0 startet das Setup Programm und installiert den Treiber. Wichtig! Starten Sie Ihren PC in jedem Fall nach der Installation neu.
ÜBERPRÜFEN DER INSTALLIERTEN TREIBER Klicken Sie auf >Start<>Programme<>Verwaltung(Allgemein)<>Windows NT-
Diagnose< danach klicken Sie auf >Ressourcen<>IRQ<. Hier werden Sie einen Eintrag z.B. „09 sysbase 0 PCI“ für die Karte finden. Klicken Sie jetzt auf >I/O-
Port<. Hier müssten Sie vier Einträge: z.B. „ D400-D407 sysbase 0 PCI“ oder „D800-D802 sysbase 0 PCI“ und „DC00-DC1F sysbase 0 PCI“ finden. Soll-
Deutsch EX-41384
6. Treiber Installation
SCO UNIX / LINUX
Die Treiber für Linux befinden sich in folgendem Verzeichnis:
"D:\IO\SYSTEMBASE\DRIVERS\PCI\SCO"
Da sich die einzelnen Distributionen und Kernelversionen sehr voneinander unterschei­den, können wir Ihnen leider keine Installationsanweisung geben. Bitte halten Sie sich an die Installationsanweisung für Standard I/O Ports Ihrer Unix/Linux Version. In eini-
gen neueren Versionen wird die Karte automatisch beim Start Installiert.
7. Technische Daten
Betriebstemperatur: 0° bis 55° Celsius
Lagertemperatur: -40° bis 75° Celsius
Rel. Luftfeuchtigkeit: 5% bis 95%
Abmessung: 130 x 34 mm
Gewicht: 500g
EX-41384 English
The EX-41384 is a plug & play high-speed serial RS-232 expansion card for the PCI Bus. The EX-41384 provides four 9 pin high speed RS-232 serial ports. It uses data transfer rates up to 921Kbaud/s. The EX-41384 design utilizes the SystemBase chipset with 256-byte buffer, which incorporates the latest in high speed interface technology. In combination with the fast PCI bus it provides a secure and very high data transfer on each port. It supports 32-bit PCI & PCI-X bus with 5 Volt and 3,3 Volt. It is not possible to change the address or IRQ settings manually, they will be obtained automatically by the system BIOS and operating system. With the jumpers you can enable power to pin
9. Please note if you use power to pin 9 your peripheral device must support it. Further-
more, you can use another jumper to set the voltage of +5V or +3,3V on the UART. There is additionally a 8 cm low profile slot bracket for installation in small computer housing.
Features:
Compatible for PCI and PCI-X bus Up to 921.6 Kbps Baud Rate Support RS-232
Support Windows NT 4.0/ 9x/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux
Certificate for CE / FCC / RoHS / WEEE DE97424562
Before you install the EX-41384 in your PC, please check at first the contents of the delivery:
EX-41384
Driver CD
Manual
Octopus Cable
Low Profile Bracket
1. Description
2. Extent of Delivery
10
English EX-41384
3.1 Layout
3.2 Connections
3. Layout and Connections
S1-S4:
44 Pin connector for octopus cable with 4 x 9 Pin serial connector
J3-J6:
Internal connectors
S1_PWR-S4_PWR:
Power to 9 Pin connector On/Off
JP1: Jumper to set the volta­ge at the UART
JP2: Select the
power over Power Supply or PCI Bus
J2: Connector for Power Supply
JP4: Only for Test purposes (Please do not change)
JP3: PME On/Off
DB9 (EX-41384) DB9 (Device)
1 DCD 1 DCD
2 RXD 2 RXD
3 TXD 3 TXD 4 DTR 4 DTR 5 GND 5 GND 6 DSR 6 DSR 7 RTS 7 RTS 8 CTS 8 CTS
1
2
3
4
SystemBase Chipset
S1-S4:
11
EX-41384 English
3. Layout and Connections
4. Jumper Settings
3.2 Connections
1 +5V 2 GND 3 GND 4 +12V
For aux power X5V and X12V (JP2), J2 must be connected to pc power supply! If not, the card wont work.
JP1:
+3.3V = The voltage level is set to 3.3V. (Factory Setting)
+5V = The voltage level is set to 5V.
If your device need a higher voltage level, then set the jumper to the posi­tion +5V.
Only If set jumper S1_PWR-S4_PWR to PWR, then you can set the volta­ge source with the jumper JP2. There are two different voltage sources (Mainboard & Power Supply).
(If the jumper JP2 set to X5V / X12V then the power connector J2 must be
connected with the PC power supply)
I5V = 5Volt from Mainboard (DEFAULT) X5V = 5Volt from Power Supply X12V = 12Volt from Power Supply I12V = 12Volt from Mainboard (DEFAULT)
I5V
X5V
X12V I12V
JP2:
+5V +3.3V
ENA | DIS
JP3:
DIS = The function PME is disable. (Factory Setting)
ENA = The function PME is enable. Now the card can be activate
the computer through the serial ports.
But this should not be adjusted for standard applications.
J2:
12
English EX-41384
4. Jumper Settings
12V 5V DIS
S1_PWR-S4_PWR:
DIS = The pin 9 is connected with RI (Ring Indicator) signal as
standard RS-232 definition. (Factory Setting)
5V = On pin 9 is now a voltage of +5V. 12V = On pin 9 is now a voltage of +12V.
There are four jumper on the board, so you can make the settings indivi­dually for each serial port. The setting of the voltage source can be adjust with JP2. But this should not be adjusted for standard applications.
5. Hardware Installation
If you are ready with the jumper settings, please proceed with the following installation instructions. Because there are large differences between PC’s, we can give you only a general installation guide for the EX-41384. Please refer to your computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Com-
puter and gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of
your computer. Make sure it is the right expansion slot for the card (see card de-
scription)
4. Align the card with the PCI slot and then gently but firmly, insert the card. Make sure
the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer’s cover and the mounting screws.
13
EX-41384 English
6. Driver Installation
Windows 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx
After starting Windows it recognizes a new “PCI Controller“ and opens the hardware assistant. Please choose manual installation and put the driver CD into your CD-Rom drive. Now enter the Path "D:\IO\SYSTEMBASE\DRIVER\PCI" and then the directory of your operating system which is installed “32bit_Win10_8.x_7_Vista_XP_20xx“ or
“64bit_Win10_8.x_7_Vista_XP_20xx” into the box for the Path/Source and click at >next/continue<. Now Windows will search for the drivers in the specified directo-
ry. Follow the hardware assistant and finish the installation. If Windows recognizes oth-
er new devices repeat the above described steps. Attention! Restart Windows in any
case after installing the drivers.
CHECK THE INSTALLED DRIVER Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the win-
dows that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find more new ”PCI Ports“ as sample (Com3). If you see this or similar entries the card is installed correctly.
CHANGE PORT NUMBER If you like to change the port number for example COM3 to COM5, open the >Device Manager< click at >COM3<, >Settings< and then >Advance<. There you can change between COM3 till COM256.
Windows 9x
Start Windows 9x and insert the driver CD into your CD-ROM drive (for example D:). After them please click at the button >Start< >Run< and then enter the follow ing path „D:\IO\SYSTEMBASE\DRIVERS\PCI\Win9x\INSTALL.exe". Windows 9x will now start the setup program and install the driver. Attention! Restart Windows 9x in any case after installing the drivers.
CHECK THE INSTALLED DRIVER Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the win-
dows that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find more new ”PCI Ports“ as sample (Com3). If you see this or similar entries the card is installed correctly.
Windows NT 4.0
Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:). After them please click at the button >Start< >Run< and then enter the follow ing path „D:\IO\SYSTEMBASE\DRIVERS\PCI\WinNT\INSTALL.exe". Windows NT will now start the setup program and install the driver. Attention! Restart Windows NT in any case after installing the drivers.
14
English EX-41384
6. Driver Installation
CHECK THE INSTALLED DRIVER Click at >Start< >Programs< >Administrative Tools[Common]< >Windows NT-
Diagnostics< then click at >Resource< >IRQ<. Here you should find the entry „09 o 0 PCI“. Then click at >I/O-Port< here you should see the entries „D400-D407 sysbase 0 PCI“ „D800-D802 sysbase 0 PCI“ and „DC00-DC1F sysbase 0 PCI“ for the ports. The I/O addresses can change depends which system and card is
installed. If you see these or similar entry's the card is installed correctly.
SCO UNIX / LINUX
The drivers are located in the following folder on our driver CD:
"D:\IO\SYSTEMBASE\DRIVERS\PCI\SCO"
Because each individual distribution and kernel version of Linux is different, sadly we cant provide a installation instruction. Please refer to the installation manual for stand­ard IO ports from your Unix/Linux version! In some newer versions of Linux the card will even be installed automatically after starting Linux.
7. Technical Information
Operating Temperature: 32° up to 131° Fahrenheit
Storage Temperature: -40° up to 167° Fahrenheit
Rel. Humidity: 5% to 95%
Size: 130 x 34 mm
Weight: 500g
Loading...