Expobar diamant User Manual

Page 1
DIAMANT
USER MANUAL
UM_EN
Part No.: 1764214_01
Page 2
DIAMANT
2
CONTENTS ................................................................................................................................................................. 2
NOTIFICATION DESCRIPTIONS ...................................................................................................................4
Notication intensity levels ...............................................................................................................................................4
GENERAL ....................................................................................................................................................................... 5
Introduction ..........................................................................................................................................................................5
General instructions ............................................................................................................................................................ 5
Warnings ................................................................................................................................................................................5
Precautions ............................................................................................................................................................................6
Intended use .......................................................................................................................................................................... 6
TECHNICAL SPECIFICATIONS ....................................................................................................................... 7
DIAMANT 2GR ...................................................................................................................................................................7
Accessories............................................................................................................................................................................7
DIAMANT 3GR ...................................................................................................................................................................8
Accessories............................................................................................................................................................................8
OVERVIEW OF COMPONENTS .................................................................................................................... 9
DIAMANT 2 GR .................................................................................................................................................................. 9
DIAMANT 3 GR ................................................................................................................................................................10
DIMENSION SKETCH ..........................................................................................................................................11
DIAMANT 2 GR ................................................................................................................................................................11
DIAMANT 3 GR ................................................................................................................................................................11
TRANSPORT .............................................................................................................................................................12
Packaging ..............................................................................................................................................................................12
Delivery inspection ............................................................................................................................................................12
INSTALLATION AND START UP .................................................................................................................12
Machine positioning ...........................................................................................................................................................12
Electrical installation ..........................................................................................................................................................13
Connection types ...............................................................................................................................................................13
Water connection ..............................................................................................................................................................14
Pressure and temperature ...............................................................................................................................................14
Starting the machine ..........................................................................................................................................................14
The porta-lter set ............................................................................................................................................................15
Inserting the porta-lter into the group .......................................................................................................................15
OPERATION ..............................................................................................................................................................16
Espresso brewing ...............................................................................................................................................................16
Steaming and frothing milk with the manual steam wand ........................................................................................17
Page 3
DIAMANT
3
Steaming and frothing milk with turbo steamer .........................................................................................................18
Dispensing hot water .......................................................................................................................................................19
CLEANING AND CARE .....................................................................................................................................20
Machine cleaning ................................................................................................................................................................20
Daily cleaning schedule .....................................................................................................................................................20
Weekly cleaning schedule ................................................................................................................................................20
Cleaning the brewing group and porta-lter ...............................................................................................................21
Cleaning the group gasket and shower plate ...............................................................................................................22
Additional handling of the machine ................................................................................................................................23
STORAGE AND DISPOSAL OF MACHINE ...........................................................................................23
Long-term storage .............................................................................................................................................................23
Machine disposal and recycling .......................................................................................................................................23
PROGRAMMING ....................................................................................................................................................24
Button function overview ................................................................................................................................................24
Machine status ....................................................................................................................................................................25
Programming using the drink buttons ...........................................................................................................................25
Display overview ................................................................................................................................................................26
Adjusting the display date and time ...............................................................................................................................26
Programming the espresso brewing dosages ...............................................................................................................27
Programming the turbo steamer temperature ...........................................................................................................27
Auto On/Off........................................................................................................................................................................28
Counters ..............................................................................................................................................................................29
Accessing and resetting the counters ...........................................................................................................................29
MESSAGES AND ALARMS ................................................................................................................................30
Display messages, alarms, and warning overview ........................................................................................................30
TROUBLESHOOTING .........................................................................................................................................31
Quick troubleshooting guide ...........................................................................................................................................31
SERVICE INFORMATION ..................................................................................................................................32
Notes: ...................................................................................................................................................................................32
Page 4
DIAMANT
4
i
NOTIFICATION DESCRIPTIONS
There are four different levels of notication intensity within this manual, as identied by signal words DANGER, WARNING, IMPORTANT, and NOTE. The level of risk and importance of the notication is determined by the following denitions. Always observe the warnings to ensure safety and prevent potential injury and product damage.
Important:
Alerts against unsafe practices. Observe Important notications to ensure food safety, prevent possible minor personal injury, or damage to the machine.
WARNING:
Indicates a potentially hazardous situation which, if the WARNING is ignored, could result in serious injury or even death.
DANGER:
INDICATES A IMMINENTLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL LIKELY RESULT IN SERIOUS INJURY AND EVEN DEATH.
Note:
Gives additional information which may be helpful during the operation, routine maintenance, and cleaning of the machine.
Notification intensity levels
Page 5
DIAMANT
5
GENERAL
Thank you for choosing a DIAMANT espresso machine. We hope you enjoy it !
Read this user manual carefully before starting
to use the machine.
This manual contains important instructions
regarding safe intended use of the machine.
Do not discard this manual, it will be useful for
future reference. If damaged or lost, request a copy from the manufacturer.
Introduction
Machine installation and certain maintenance
operations should only be performed by qualified service personnel.
All safety instructions and warnings contained
in this manual should be observed at all times to ensure safe installation, use, and maintenance.
Do not attempt to remove covers or safety
shields to access the interior of this machine or make repairs. Repairs should be made by an authorised technician or service centre.
Owners are liable for ensuring that users have
been properly trained to operate the machine and understand the potential risks involved.
The owner or installer will be liable for all non-
authorised modification of the machine.
Non-authorised alteration or modification
of the machine will immediately void the manufacturer’s warranty.
This manual references the machine at the
time of sale. The commercial availability of subsequent versions including modifications, upgrades or adaptations does not oblige the manufacturer to apply any changes to this machine, nor is it obliged to update the documentation supplied.
The manufacturer reserves the right to
withdraw currently available manuals whenever deemed appropriate and reasonable.
Periodically, some updates and changes may
be required for this machine. In this event, a technician will be responsible for ensuring the change is made in accord with manufacturer’s specifications.
Install the machine in a horizontal position and
away from heat sources and flammable objects.
This machine should only be installed on a
water-resistant work surface that is capable of adequately supporting the machine’s weight.
Place the machine in a location accessible only
to personnel trained to operate it.
Keep all hazardous packaging materials, such as
plastic bags, styrofoam, and staples, out of reach of children.
Plug the machine into a properly installed, earth
grounded electrical outlet with line voltage that matches the specifications for the machine.
Ensure that the power supply voltage does not
fluctuate by more than 6%.
Position the power cable so that users cannot
trip over it. Keep the power cable away from sharp edges and heat sources.
Children should never be allowed to play with
the machine.
This appliance is not suitable for installation in
an area where a pressure washer may be used.
Do not use the machine outdoors, where
it would be exposed to severe weather or extreme temperatures..
If the power cable is damaged, it may only be
replaced by the manufacturer or its approved service technician.
Do not remove or disable any of the
mechanical, electrical, or thermal protection safety equipment.
General instructions
Warnings
Note:
The manufacturer is not liable for damage to persons or property resulting from failure to
follow the instructions and warnings listed below when installing and using this machine.
Page 6
DIAMANT
6
GENERAL
In case of emergency, (e.g., the machine catches
fire or becomes unusually hot or noisy), disconnect the power immediately and turn off the water supply.
If the machine is not going to be used for an
extended period of time, disconnect the power. When disconnecting the power, pull the plug rather than the cable.
When packed for storage, store the machine
in a dry place with an ambient temperature above 5ºC. Boxes may be stacked up to three
units high of the same model. Do not place other heavy items on top of the box.
If the machine is likely to be exposed to
temperatures below 0 ºC during handling and transport, make sure that service personnel empty the boiler and water system. (The machine’s boiler and water system is empty when delivered from the factory.)
To ensure fault-free machine operation, only
use manufacturer-approved replacement parts and accessories.
The coffee machine has been designed and
manufactured to make espresso coffee and other hot drinks (e.g., steaming and frothing milk). Do not use it for any other purpose.
The machine is intended to be used by trained
personnel for preparing foodstuffs.
This machine is not intended for use in
industrial kitchens, domestic kitchens, or similar locations.
The manufacturer will not be held liable
for damage to persons or property due to incorrect, improper or negligent use by non­professional personnel.
To ensure optimal performance, install the
machine in a location where these parameters will not be exceeded:
- Maximum permissible inlet water pressure: 600 KPa (6 Bar)
- Minimum permissible inlet water pressure: 200 KPa (2 Bar)
- Maximum inlet water temperature: 40ºC
- Ambient temperature is between +10 ºC
(min.) and +40 ºC (max.).
Precautions
Intended use
Before performing maintenance and/or moving
the machine, disconnect the machine from the
power supply and wait for it to cool down. Do not place any liquids on the machine. This appliance must not be cleaned with a
pressure washer. Never immerse the machine, plug or power
cable in water, as there is a risk of electric
shock. Do not touch the machine’s hot surfaces or
dispensing equipment. Do not touch the machine if your hands or feet are
wet. Do not operate the machine if any part except
the dispensing equipment is wet. Place the machine out of reach of children. This appliance can be used by children from
age 8 and above and persons with reduced
physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Do not use the machine if the power cable
or plug is damaged, or the machine has been dropped. Contact a service technician for repairs or to ensure that it is safe for use.
Do not block the vents with rags or other
objects. Do not insert foreign objects into the vents. Check the drain regularly to make sure that
waste water is emptying properly.
Page 7
DIAMANT
7
DIAMANT 2 GROUP
Accessories
ITEM
2-spout
porta-lter
1-spout
porta-lter
55-cm inlet
hose
Blind lter
Drainage tube
(150 cm)
2 GROUP:
2 unit 1 unit 1 unit 1 unit 1 unit
TECHNICAL SPECIFICATIONS
SPECIFICATIONS
MODEL
DIAMANT 2 GROUP
(Base) | (Std.)
DIAMANT 2 GROUP -
WITH 3 BOILERS
Steam wand 2 units 2 units
Turbo steamer
none
| 1 unit
1 unit
Hot water outlet
1 unit
| 2 units
1 unit
Temperature control PID regulation PID regulation
Temperature control by group No Ye s
Programmed via display Ye s Ye s
Dispensing system for tall cups Optional Optional
Energy saving mode Ye s Ye s
Width, depth, height (mm) 880, 620, 595 880, 620, 595
Boiler volume (L) 11.5 11.5 + 1.5 + 1.5
Power supply
230V 1N~ 3740 W 50/60 Hz 230V 1N~ 3740 W 50/60 Hz
400V 3N~ 4780 W 50/60 Hz 400V 3N~ 4790 W 50/60 Hz
230V 3~ 4790 W 50/60 Hz 230V 3~ 4790 W 50/60 Hz
Water connection Female 3/8" thread Female 3/8" thread
Machine weight (kg) 51.50 60.90
Steam boiler operating pressure Between 0.8 and 1.2 bar Between 0.8 and 1.2 bar
Ambient noise < 70 db < 70 db
Page 8
DIAMANT
8
DIAMANT 3 GROUP
Accessories
MODEL
2-spout
porta-lter
1-spout
porta-lter
55-cm hose Blind lter
Drainage tube
(150 cm)
3GR
3 unit 1 unit 1 unit 1 unit 1 unit
TECHNICAL SPECIFICATIONS
SPECIFICATIONS
MODEL
DIAMANT 3 GROUP
(Base) | (Std.)
DIAMANT 3 GROUP -
WITH 4 BOILERS
Steam wand 2 units 2 units
Turbo steamer
none
| 1 unit
1 unit
Hot water outlet
1 unit
| 2 units
2 units
Temperature control PID regulation PID regulation
Temperature control by group No Ye s
Programmed via display Ye s Ye s
Dispensing system for tall cups Optional Optional
Energy saving mode Ye s Ye s
Width, depth, height (mm) 1080, 620, 595 1080, 620, 595
Boiler volume (L) 17.5 17.5 + 1.5 + 1.5 + 1.5
Power supply
400V 2N~ 4290 W 50/60 Hz 400V 2N~ 4290 W 50/60 Hz
400V 3N~ 6290 W 50/60 Hz 400V 3N~ 6290 W 50/60 Hz
230V 3~ 4290 W 50/60 Hz 230V 3~ 4290 W 50/60 Hz
Water connection Female 3/8" thread Female 3/8" thread
Machine weight (kg) 73.45 81.40
Steam boiler operating pressure Between 0.8 and 1.2 bar Between 0.8 and 1.2 bar
Ambient noise < 70 db < 70 db
Page 9
DIAMANT
9
COMPONENT OVERVIEW
Machine Front View
DIAMANT 2 GROUP
Steam Lever
Steam Lever
Display
Hot Water Button
Steam Button
Drink Buttons
Pump Manometer
Turbo Steamer
Hot Water Outlet
Hot Water Outlet
Porta-filter Porta-filter
Brewing Groups
Steam Wand
Steam Wand
Main Power Switch
Page 10
DIAMANT
10
OVERVIEW OF COMPONENTS
Machine Front View
DIAMANT 3 GROUP
Steam Lever
Steam Lever
Hot Water Button
Steam Button
Drink Buttons
Pump Manometer
Turbo Steamer
Hot Water Outlet
Hot Water Outlet
Porta-filters
Brewing Groups
Temperature Sensor
Steam Wand
Steam Wand
Main Switch
Display
Page 11
DIAMANT
11
DIMENSION SKETCH
DIAMANT 2 GROUP
DIAMANT 3 GROUP
Model A
B C
DIAMANT 2GR
880 mm 620 mm 595 mm
Model A
B C
DIAMANT 3GR
1080 mm 620 mm 595 mm
C
A
A
B
B
C
Page 12
DIAMANT
12
TRANSPORT
INSTALLATION AND START-UP
Machine positioning
Packaging
Delivery inspection
Install the machine on a level, sturdy, and water-resistant
surface approximately 110cm above floor level for ease of access and usage.
Adjust the feet to ensure that it dispenses coffee evenly to
all cups.
Ensure enough free space is available above (>30cm) and behind (>10cm) the machine to ensure easy cleaning and maintenance and adequate ventilation.
Do not install the machine if it is wet or damp. Allow it to
dry completely and ask a service technician to ensure that none of the electrical components have been affected.
Note:
Leave an air gap of approximately 30cm above the machine and 10cm behind it to ensure adequate ventilation.
i
MIN. 10 cm
MIN. 30 cm
The machine is shipped in a custom-designed carton which utilizes model-specific polystyrene
cushions to protect it from damage.
The machine’s carton features standardized handling symbols to explain proper shipping and
storage methods.
The machine must remain in a horizontal position during the transport. Do not store or handle the
machine except on its feet.
During transport protect the carton and machine from impact drops, crushing, shocks, moisture
and exposure to extreme temperature.
Upon receipt and delivery ensure that the machine is in the exact condition described in the
enclosed documentation, and that all accessories are included. Missing items should be reported to the manufacturer or dealer immediately.
Damage caused during transport should be reported to the shipping agent and the machine’s
distributor immediately.
Packaging materials are potentially dangerous and should be kept away from children.
The carton and all packing materials are recyclable and should be returned to a recycling center for
disposal.
Page 13
DIAMANT
13
INSTALLATION AND START UP
Connection types
Machine: Supply
230Vac Ph+N
NEUTRAL
PHASE
Supply cable
Blue
Brown
Yellow/Green
230Vac Ph+N
Machine: Supply
2Ph 230Vac
PHASE
PHASE
Blue
Brown
Yellow/Green
230Vac Ph+N
Machine: Supply
3Ph 230Vac
PHASE
Blue Brown
Yellow/Green
230Vac 3Ph
Machine: Supply
230Vac Ph+N
NEUTRAL
PHASE
Supply cable
Blue Brown
Yellow/Green
2Ph+N
Black
Machine: Supply
2Ph 380Vac+N
NEUTRAL PHASE
Blue Brown
Yellow/Green
2Ph+N
PHASE
Black
Machine: Supply
2Ph 230Vac
NEUTRAL
PHASE
Supply cable
Blue Brown
Yellow/Green
2Ph+N
Black
Machine: Supply
3Ph 230Vac
PHASE
Blue Brown
Yellow/Green
2Ph+N
Black
PHASE
PHASE
Machine: Supply
125Vac Ph+N
NEUTRAL
PHASE
Blue
Brown
Yellow/Green
125Vac Ph+N
Machine: Supply
3Ph 380Vac+N
NEUTRAL PHASE
Blue Brown
Yellow/Green
380Vac 3Ph
Grey Black
PHASE PHASE
Black
PHASE
PHASE
Electrical installation
The machine should only be connected to the power supply by qualified personnel. The following safety instructions should be obeyed at all times:
Ensure that the electrical requirements stated on the TECHNICAL
SPECIFICATIONS (pages 7 - 8) match the specifications of the power supply at the outlet.
Ensure that the domestic electrical supply where the machine is being installed is rated for and able to provide the power required by the machine. Insufficient power supply, wiring, grounding, or insulation can result in overheating and possibility of fire.
The coffee machine must be connected to an earth grounded electrical
outlet that complies with the regulations in force in the country of installation.
Ensure that a circuit breaker engineered for the power consumption of the
machine is installed to protect the domestic electrical supply, as specified on the ratings plate located under the drip tray.
Do not connect the machine to the domestic power supply via extension
cords, plug adapters, or shared outlets.
The manufacturer will not be held liable for damage to persons, animals or property resulting from incorrect installation of the coffee machine.
DANGER!
If the power cable or plug is damaged, it must be replaced by the manufacturer, distributor, or its approved service technician in order to avoid RISK OF SERIOUS INJURY OR DEATH!
Connect the machine according to the specification on the ratings plate located under the drip tray.
Supply cable
Supply cable
Supply cable
Supply cable
Supply cable
Supply cable
Page 14
DIAMANT
14
INSTALLATION AND START UP
Main power switch
Water connection
Connecting the machine to the domestic water supply must be performed by a qualied person. Purge at least 20 liters of water from the domestic water supply before connecting the machine to it to ush out
any debris that may be in the plumbing system that would otherwise accumulate inside the boilers.
The domestic plumbing system should be tted with a brass 3/8” NPT male pipe tting and an in-line
shut-off valve. Connect the 180cm water inlet hose included with the machine to the domestic water supply and tighten the line ttings with a wrench to 15 ft. lbs. / 20N-m.
Only use safe drinking water with a hardness rating between 5ºfH and 8ºfH (French hardness
degrees) or 20 to 32 ppm (parts per million as calcium). If the hardness value is below this limit, corrosion of hydraulic components is likely. If the value is higher, lime-scaling inside the boiler will occur. In both cases, the proper function of the machine and quality and taste of the coffee will be negatively affected.
If necessary, connect the machine to a water softener to reduce water hardness using the exible 55cm
hose included in the accessory box.
Connect one end of the corrugated drain tube to the drain cup in the machine, connect the other
end to the plumbing drainage system in the installation area.
Pressure and temperature
Starting the machine
Boiler pressure is directly controlled by water temperature (g. 01). This machine is tted with a pressure gauge that displays the boiler pressure, if the machine is
equipped with a digital display it will also indicate water temperature.
Relationship between boiler pressure and temperature
Standard operating pressure and temperature
0.7
110
115
120
125
0.8 0.9 1 1.1 1.2
o
C
BAR
Important:
Only use the hoses supplied with the machine. Never reuse damaged hoses. Ensure that the drainage tube is not twisted and that it is below the level of the drain cup.
g. 01
Open the machine’s water supply valve. Turn on the main power switch. Press a drink button at the control panel on each
group, wait until water comes out continuously from each of them. This ensures that the heat exchangers in the machine are being correctly lled.
Open the steam lever to release the air trapped in
the boiler.
The red lamp indicates that the boiler is heating. The
lamp switches off automatically when the machine reaches operating temperature.
The machine is now ready to use.
Page 15
DIAMANT
15
INSTALLATION AND START UP
The porta-filter sets
Filter basket locking spring
Filter basket
Porta-filter spring slot
Porta-filter & filter basket for double espresso (14g)
Porta-filter and filter basket for single espresso (7g)
Correct
position.
Porta-lter not
fully inserted.
Group gasket is
worn out, please replace.
Align the porta-filter's two flanges with
the two slots in the group housing.
Insert the porta-filter and rotate it counterclockwise
until the handle is apporximately perpendicular to the face of the coffee machine.
(+/- 5 degrees)
Porta-filter
Inserting the porta-filter into the group
Page 16
DIAMANT
16
OPERATION
Espresso brewing
01 02
03 04
05
06
Important:
Always keep the porta-lter inserted in the group to keep it warm. This is important to maintain an optimal temperature when the espresso is dispensing.
Unlock and remove the porta-filter
from the group head.
Press the coffee with the
coffee tamper.
Place the cup(s) under the
porta-filter outlet(s).
Select the desired option from the
drink buttons.
Insert the filled porta-filter into
the group head and lock it into the correct position.
Fill the lter basket with
espresso-grind coffee (amount will differ depending on lter basket size). For best results use only freshly ground espresso beans.
WARNING!
Never try to open the porta-lter while the machine is in operation! The pressurised hot water could cause scalding or serious injury. After dispensing has nished, wait at least 3 seconds before removing the porta-lter.
Page 17
DIAMANT
17
OPERATION
Steaming and frothing milk with the manual steam wand
Steaming
Frothing
Place the steam wand over the drip tray and
open the steam lever for a few seconds to allow condensed water to be ejected. Close the steam lever when only steam comes out.
Open the steam lever again to begin steaming or frothing
the milk. Do not remove the milk pitcher while steaming.
Once the milk reaches the desired
temperature, close the lever and remove the pitcher.
Immerse the steam wand into the milk,
making sure the wand tip is submerged.
After the process is finished, position the steam wand
over the drip tray and open the steam lever for a few seconds to eject any milk remaining in the wand.
Close the lever and then wipe down the outside of
the steam wand with a damp cloth to prevent nozzle blockage and to keep it clean. Leaving milk in or on the wand will affect the taste of later drinks.
WARNING!
Do not allow the steam wand to extend out of the milk when the lever is open, it may cause serious burns and injuries.
01 02
03 04
05
Page 18
DIAMANT
18
Steaming and frothing milk with the turbo steamer
OPERATION
03
04
05
Place the steam wand over the drip tray and
open the steam lever for a few seconds to allow condensed water to be ejected. Close the steam lever when only steam comes out.
Immerse the steam wand and temperature
sensor into the milk pitcher, making sure the wand tip is submerged.
Press the button again to begin steaming or frothing the milk.
Do not remove the milk pitcher while steaming.
Once the milk reaches the
programmed temperature, the steaming will stop automatically and the pitcher can be removed.
WARNING!
Do not allow the steam wand to extend out of the milk when the milk is being steamed or frothed, it may cause serious burns and injuries.
After the process is finished, position the steam wand over
the drip tray and press the steam button once, allowing steam to flow for a few seconds to eject any milk remaining in the wand. Press the button again to stop the steam and then wipe down the outside of the steam wand with a damp cloth to prevent nozzle blockage and to keep it clean. Leaving milk in or on the wand will affect the taste of later drinks.
05
01
02
Page 19
DIAMANT
19
OPERATION
Dispensing hot water
WARNING!
Never expose hands and ngers directly under the hot water outlet during operation to avoid scalding or serious burns.
Place a pitcher (or other heat resistant vessel) under the hot water outlet.
Press the hot water button (A) for 3 seconds to begin dispensing.
Wait until the machine stops dispensing hot water automatically, or press the
button again to stop hot water dispensing at any time.
A
Page 20
DIAMANT
20
CLEANING AND CARE
Machine cleaning
Daily cleaning schedule
Weekly cleaning schedule
Important:
To keep the machine looking and working like new, you should always follow the cleaning
and care instructions provided in this manual. Always turn off the main power switch when cleaning the exterior of the machine. All external surfaces should be cleaned with a damp, lint-free cloth that will not scratch the
machine. Do not use aggressive cleaning detergents, solvents or degreasers. These can damage the
surfaces, and plastic and rubber parts, and leave unwanted residue.
Important:
Each day, or 8 hours after dispensing the last coffee, the following cleaning tasks should be performed to maintain the quality and performance of the water system:
Porta-filter: Brew one espresso with the filter empty (around one minute) to flush it out
(dispose of this water). Steam Wand: Position the wand over the drip tray and open the steam lever for one minute
to flush the wand. Hot Water Outlet: Place a container under the water outlet and open the lever for 20
seconds (dispose of this water).
Rinse each of the brewing groups, shower plates, and porta-filters with hot water for 15 seconds.
Clean the external surfaces of the machine with a damp cloth, paying special attention to the
stainless steel parts.
Clean the steam wand and the water tap. Be sure that the nozzles are not clogged or partially
blocked with milk or other residue. If it’s necessary to remove them for cleaning, be careful not to deform or damage any of the components during removal.
Clean the dip tray and the stainless steel insert grid under running water with a brush.
Clean the drain cup by slowly pouring one liter of warm water into it to dissolve and remove the
coffee residue that accumulates inside the drain cup and hose.
Clean the brewing group and porta-lter with professional cleaning powder (page 21).
Page 21
DIAMANT
21
CLEANING AND CARE
Cleaning the brewing group and porta-filter
WARNING!
Never try to open the porta-lter while the machine is in operation! The pressurised hot water could cause scalding or serious injury. After cleaning has nished, wait about 3 seconds before removing the porta-lter.
Unlock and remove the porta-filter from the group head. Place the blind gasket in the filter basket. Fill the blind basket with cleaning powder for espresso coffee machines. Lock the porta-filter into the group head. Activate the auto-cleaning program:
When the machine is in idle mode, simultaneously press the Continuous and 1 Short
Espresso buttons. After cleaning starts, release the buttons and the machine will
automatically repeat the cleaning cycle 5 times until cleaning is completed.
Important:
When the cleaning process is nished, remove the porta-lter and run water through the group again to rinse out any residue. Repeat the cleaning process this time without cleaning powder to remove any remaining residue. Store the blind gasket in a convenient location for future use.
Note:
Rinse the group and porta-lter with hot water (using only the blind gasket and hot
water, no cleaning powder) each day.
Clean the group and porta-lter with cleaning powder once a week.
Blind gasket
Espresso machine cleaning powder.
Note:
Only use professional cleaning powder designed specically for espresso machines. It’s available from the distributor.
i
i
Part no: 1104162
Page 22
DIAMANT
22
CLEANING AND CARE
Cleaning the group gasket and shower plate
While making espresso, coffee grounds will naturally accumulate on the group’s sealing surface. Allowing an excessive amount of grounds to build up can prevent the porta-filter from properly sealing to the group head. In extreme cases, such as leaving a used porta-filter in the group head for several days, water can even become blocked from passing through the shower plate.
To prevent these problems, perform the following cleaning procedures daily:
Install the blind basket into the porta-filter without cleaning powder. Place the porta-filter loosely in the group head - do not close it fully. Press the Continuous button . Perform an opening-closing motion with the porta-filter in place without closing it fully. Water
will flow over and around the porta-filter, passing through the closing surface and washing out any coffee residue. Be very careful to avoid splashes, as this water is very hot and can cause burns.
Press the Continuous button again to stop the water flow.
Remove coffee residue with a food-safe brush
Shower plate
WARNING!
Take special care to avoid scalding when performing this cleaning operation, as the hot water used to clean the gasket will spill over the sides of the porta-lter.
WARNING!
Do not fully tighten the porta-lter. If fully tightened, high-pressure water may spray out and cause scalding or serious injury.
Cleaning the gasket
Cleaning the shower plate
Remove the porta-lter from the group head. Clean the shower plate and group gasket with a soft brush to remove any coffee residue.
Page 23
DIAMANT
23
CLEANING AND CARE
Always remove and insert the porta-lters
gently. Never use excessive force to try to close the porta-lter. If the porta-lter does not turn and lock into place without excessive force this usually indicates that there is too much coffee in the lter basket.
Additional handling of the machine
Long-term storage
Machine disposal and recycling
Important:
Do not place wet cups directly on the cup shelf. Allowing water to drip into the machine can cause mechanical and electrical damage.
STORAGE AND DISPOSAL
Before storage be sure to:
Perform all weekly and periodic cleaning procedures described in this manual (see pages 16-20).
Disconnect and roll up the power cord (this should be performed by a qualified person).
Disconnect the machine’s water inlet hose from the domestic water supply and drain the boilers (this
should be performed by a qualified person).
Clean the drip tray and exterior of the machine to remove any coffee or other residue.
Cover / re-pack the machine in its original carton and store it in a dry place where it will not be
exposed to extreme temperatures or humidity.
When returning the machine to service after long-term storage, perform all weekly and periodic
cleaning procedures before use.
Disconnect and roll up the power cord (this should be performed by a qualified
person).
Disconnect the machine’s water inlet hose from the domestic water supply and
drain the boilers (this should be performed by a qualified person).
Pack up and ship/deliver the machine to a certified recycling center.
Page 24
DIAMANT
24
PROGRAMMING
Water Button
Turbo Steam Button
Digital control panel
Button function overview
The following functions can be programmed and controlled from the digital display:
Volume control of four different espresso drinks per brewing group.
Timed hot water dispensing.
Automatic boiler filling and level control.
Automatic heating element shut-down in event of a low water condition.
System supervision through messages, warning, and alarms.
Automatic cleaning of the brewing groups.
The digital controller is programmed with four standard drink functions (these can be reprogrammed as desired by the user) and one continuous function from the manufacturer.
The upper four buttons (1 Short Espresso, 1 Long Espresso, 2 Short Espressos, 2 Long Espressos) will brew the programmed beverage volume and then stop automatically.
The fifth/bottom button (Continuous) brews continuously until the user stops it by pressing the button again.
1 Short Espresso
1 Long Espresso
2 Short Espressos
2 Long Espressos
Continuous
Depending on how long this button is pressed, it has 3 separate functions:
Less than 1 second activates the hot water outlet.
Between 1 and 8 seconds activates continuous espresso dispensing through
the capsule group. To stop the dispensing, press the button again.
Longer than 8 seconds activates the programming menu (see pages 25-31).
Digital Display
Displays boiler
temperature and water level.
Displays date and time (optional, if desired).
1 Short Espresso
2 Short Espressos
1 Long Espresso
2 Long Espressos
Continuous
Page 25
DIAMANT
25
PROGRAMMING
Machine status
Programming using the drink buttons
Turning the Boiler ON or OFF-
With the machine in ON status, press the Continuous
and 1 Long Espresso buttons
simultaneously to turn the boiler ON or OFF (multi-boiler machines only).
Standby Mode-
On the left keypad, press and hold the Continuous button
then press the 2 Short Espressos
button
, this will put the machine in STANDBY mode.
Automatic Cleaning-
With the machine in ON status, press the Continuous
and 1 Short Espresso
buttons simultaneously to activate the automatic cleaning function.
Activating the Programming Menus-
There are two programming menus that can be adjusted while the machine is in ON status. The
first programming menu is reached by pressing the Continuous button
for 8 seconds,
until the “Doses Program” is shown on the display. From this program it is possible to access the
second menu by pressing Continuous button
again for 8 seconds. Learn more about these
programming menus and their functions in the following pages.
C
A
B
D
The machine has 3 different statuses:
ON
The machine is active and ready for use. Generally when switching on the main
switch, the machine will enter this status quickly. (See “ON” fig.A)
STANDBY
The main switch is turned on, but the machine’s display reads OFF (See
“STANDBY” fig.B). This is a power saving mode. To get to this status, begin
with the machine in ON status. Press and hold the Continuous button , then press the 2 Short Espressos button . The display will read “OFF” and go to STANDBY status. To exit STANDBY status press the button 2 Short Espressos button again, the machine will return to ON status.
OFF
The machine is totally powered down or electricity is disconnected.
Publicity
EXPOBAR
Max
hh:mm
day
o
C
Min
OFF
hh:mm
day
“ON” fig.A
“STANDBY” fig.B
Page 26
DIAMANT
26
PROGRAMMING
Accessing the Date and Time Program:
1. Press the Continuous button
for 8 seconds. All buttons on the
keypad will light up and Continuous button will flash. The machine is now in
the “Doses” Program (See fig. A).
2. Press the Continuous button
again for 8 seconds and the “Clock
Adjust” Program will appear (See fig. B).
Setting the Date and Time:
3. From within the “Clock Adjust” Program press the 2 Short Espresso button
once, the “HH” hour indicator will begin to flash. (See fig. C)
4. Adjust the Hour up or down using the 1 Short Espresso
and 1 Long
Espresso buttons
until the desired hour is showing. Then press the
2 Short Espresso button
to move on and adjust the Minute (MM)
and date (Day) in the same manner.
Publicity
EXPOBAR
Machine Name
Boiler Water
Level Indicator
Boiler Temperature
Indicator
Max
hh:mm day
Time and Date
o
C
Min
Display overview
Doses Programming
Select 30s
Clock Adjust
HH:MM Day
fig.A
fig.B
The digital display provides information, warnings, and controls for:
Boiler’s water volume and temperature. Coffee brewing and beverage dosing time adjustment. Low water, temperature sensor, and filter service alarms and warnings .
1 short espresso +
1 long espresso -
2 short espresso OK
Continuous to conrm
Adjusting the display date and time
Clock Adjust
HH:MM Day
1 short espresso +
1 long espresso -
2 short espresso OK
Continuous to conrm
fig.C
Page 27
DIAMANT
27
PROGRAMMING
Press the Continuous button for 8 seconds, all the lights in the keypad will light up and
Continuous button will flash, the display will read “Doses Programming Select 30s”.
Immerse the steam wand in the milk to be steamed or frothed.
Press the Steam button . The programmed temperature will appear on the digital display.
When the liquid reaches the desired temperature, press the Steam button again to stop
steaming. The new temperature is now stored.
Programming the turbo steamer temperature
Note:
The electronic temperature probe is designed to automatically stop the steam when the programmed temperature is reached. Steaming times with the Turbo Steamer will vary depending on the volume and temperature of the liquid being steamed or frothed, but final temperature will be
the same.
i
Use the following steps to program the espresso brew dosages for each Brewing Group and Drink Button
(each button can be programmed for a different dosing time if desired):
1. Place a Porta-filter filled with fresh espresso grounds in the Brewing Group.
2. Press the Continuous button
for 8 seconds, all the lights in the keypad will light up and
Continuous button will flash, the display will read “Doses Programming Select 30s”.
3. Within 30 seconds press the Drink Button to be reprogrammed. All of the button lights will turn off except for the Continuous button and the one being programmed. Water will begin to flow and espresso will begin dispensing.
4. Allow the beverage to dispense until the desired drink volume is reached, then press the Drink Button that is being programmed to stop the water flow. This dosage time will now be stored as the default for that Drink Button.
5. Repeat Steps 1-4 for all Drink Buttons to be reprogrammed.
Programming the espresso brewing dosages
Note:
Programming any of the options on the left-side bank of Drink Buttons (when viewing the machine from the front) automatically programs the dosages on all of the other corresponding Drink Buttons for the other Brewing Group(s). Always program the left-side buttons first, then program the other Drink Buttons to the right afterward to store their specific dosages.
Note:
For safety and water conservation, all brewing settings have a maximum dispensing time of 5 minutes.
i
Important:
Use a porta-lter lled with fresh espresso grounds for every new brewing dosage that is programmed.
i
Page 28
DIAMANT
28
PROGRAMMING
Auto On/Off
Auto On/Off” Program controls when the machine will automatically turn
on and off via preset times when the main power switch remains on. This is a power saving feature.
Closed on Day” Program is a power saving feature that allows users to specify one day per week that the machine will not be used, and therefore should not turn on, heat the boiler, and go into On status. This feature is optional and should only be used if needed.
Setting the “Auto On/Off” Program:
1. From within the “Clock Adjust” Program (see page 24) press the 2 Short
Espresso button
to enter the “Auto ON/OFF” Program (See fig. A).
The “ON” function will begin to flash.
2. Adjust the “ON” status by pressing the 1 Short Espresso or 1 Long
Espresso
buttons to move the hour value up and down that the
machine is expected to automatically start on. When the desired hour is
input (See fig.B), press the 2 Short Espressos button
to accept and
move to the minute input. Then adjust the minute value using the 1 Short
Espresso
or 1 Long Espresso buttons.
3. When the hour and minute that the machine will automatically turn ON has
been correctly input, press the Continuous button to accept the
program and move to the “Auto Off” Program. Programming the “OFF”
time is done in the same manner as the “Auto On” time by repeating steps
1 through 3 from above.
Setting the “Closed on Day” Program:
1. After “Auto ON/OFF” times have been confirmed, a day off can be
programmed using the “Closed on Day” Program (See fig. C). This feature is
only available when Auto On/Off is programmed.
2. To program the “Closed on Day” press the Short Espresso
or
1 Long Espresso
buttons until the desired day of the week is
showing
on the display. Then press the 2 Short Espressos button
to accept it.
Auto On/Off
On: Hh:mm
Auto On/Off
Off: Hh:mm
1 short espresso ↑ +
1 long espresso -
2 short espresso OK
Continuous to conrm
1 short espresso ↑ +
1 long espresso -
2 short espresso OK
Continuous to conrm
Closed on
Day
1 short espresso ↑ +
1 long espresso -
2 short espresso OK
Continuous to conrm
fig. A
fig.B
fig.C
i
Note:
By default, the first value of each program will be - - : - - to indicate that the function is disabled. When a value is added the function will be enabled. To leave any function disabled, simply press the 2 Short Espressos button while the display reads - - : - - to move on to the next function.
i
Note:
To exit from a program at any time press the Continuous button
to scroll back to the home display screen. The number of button presses will vary depending on the program in use.
Page 29
DIAMANT
29
PROGRAMMING
Counters
Accessing and resetting the counters
This machine has 4 self-operating counters that keep track of the following information:
Total litres of water that have cycled through the machine: Helpful in determining when cleaning and
decalcifying is required.
Service: Indicates when the machine needs technical service.
Total coffee and hot water servings brewed.
Coffee brewings for each button: Helpful in calculating approximate cost of various coffee and
beverage capsules used.
Clock Adjust
Counters
1 short espresso ↑ +
1 long espresso -
2 short espresso OK
Continuous to conrm
1 short espresso ↑ +
1 long espresso -
2 short espresso OK
Continuous to conrm
Accessing the Counters:
1. From within the “Clock Adjust” Program (see page 24) press the Continuous
button
to access the “Counters” (See fig.A).
2. Press the Continuous button
again to scroll through the “Counters”.
3. To exit the “Counters” press the Continuous button
until the
display returns to the date, time, and boiler information.
Resetting the Counters:
1. From within the “Counters” function press the 1 Short Espresso
and 2 Short Espressos buttons simultaneously. This will reset all
counters to zero.
fig. A
fig. B
Page 30
DIAMANT
30
Alarm flowmeter
X
Max
o
C
Min
No water
Max
o
C
Min
Tprobe Unconnect
X
Max
o
C
Min
Service
9999999
Max
o
C
Min
Filter
999999999
Max
o
C
Min
Flowmeter X Alarm:
Indicates no water flow is being detected by flowmeter X.
No Water Warning:
Indicates that the machine is not receiving water.
Temperature Sensor Warning:
Indicates that the temperature sensor is not functioning.
Service Alarm:
Indicates that technical service is needed.
Filter Alarm:
Indicates that the water softener filter needs to be replaced.
MESSAGES AND ALARMS
Display messages, alarms, and warnings overview
Page 31
DIAMANT
31
TROUBLESHOOTING
Problem Possible Cause Solution
The machine will not turn on.
The plug is not correctly plugged into the power source.
Ensure that the plug is correctly plugged and that the power source is operational.
The circuit breaker and/or differential are disconnected.
Ensure that they are connected and operational.
The cable and/or plug are damaged.
Call a service technical to replace it.
The steam wand will not dispense steam.
The steam wand is clogged with dried milk residue.
Clean the wand and, if necessary, remove the nozzle and unclog it using a pin or needle.
Water is found underneath the machine.
The drain tube is blocked or disconnected.
Clean the drain cup or reconnect the drain tube.
The following troubleshooting steps should only be done when the machine has been turned off and disconnected from the main power supply. For all other unspecied machine faults, disconnect the machine from the power supply and immediately contact the authorised and qualied service technician.
Faults Produced by Limescale
Coffee not dispensed at the correct temperature.
Heat-exchanger outlet pipes are clogged with limescale.
Brewing groups do not dispense water. Water system is clogged with limescale.
90% of faults are due to limescaling inside the coffee machine (due to not softening the water). To avoid these faults, maintain the water softener regularly.
Quick troubleshooting guide
Page 32
DIAMANT
32
Notes:
SERVICE INFORMATION
Page 33
www.creminternational.com
Your Dealer
FOR SERVICE
Please contact your dealer
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precautions have been taken, and warranty claim has been issued without delay.
The affected equipment shall not be used while awaiting service if there is any risk that the damage or defect could worsen.
The warranty shall not cover consumable supplies such as glassware, or normal maintenance such as cleaning of filters. Additionally, damages of an external nature, such as contaminants in the water, limescaling, incorrect voltage or power surges, and water supply issues such as pressure changes or service disconnection are not covered by this warranty.
The warranty will not cover damages or defects caused by incorrect handling or operation of the appliance.
Loading...