The HP18 LightSpot Programmer is a user-friendly remote controller for use with infrared-enabled
Key Graphic
1
2
3
4
5
6
7 5 minutes Automatic Dis abled
8 10 minutes Automatic Disabled
9 20 minutes Automatic Disabled
10 5 minutes Automatic Enabled
11 10 minutes Automatic Enabled
12 20 minutes Automatic Enabled
13 5 minutes Semi-automatic Dis abled
14 10 minutes Semi-automatic Dis abled
15 20 minutes Semi-automatic Dis abled
16 5 minutes Semi-automatic Enabled
17 10 minutes Semi-automatic Enabled
18 20 minutes Semi-automatic Enabled
Hold this button to dim the light to required level
Walk Test: Sets the time delay to 10 seconds s o
that detector operation can be checked
Keys 7-18 set these
function combinations:
Tim e Delay Mode Phot ocell
Function
Turns lights ON
Hold this button to raise the light to required level
Sets the light level thresholds for the photocell
Turns lights OFF
Ex-Or detectors (see ‘Product Compatibility’ on back page). The HP18 can be used to trigger a total of
18 functions: 6 basic and 12 programming functions.
Operating Instructions
The programmer must be pointed directly at the detector for the IR signal to
be effective. When buttons 6-18 are pressed the lights will switch OFF and
ON momentarily to confirm the command has been successfully received.
The following functions can be set using this programmer:
Time Delay This value sets how long the lights will stay ON
Automatic Mode Lights turn on when movement is detected and off
Semi-Automatic Mode Lights turn off when movement ceases but must be
Photocell Enabled Detectors can adjust the light levels according to
Photocell Disabled Light levels are not influenced by ambient light
once movement has ceased.
min
when movement ceases. Also known as Presence
AUTO
Mode.
manually turned on first. Also known as Absence
Mode.
ambient light conditions.
conditions.
Start-up and Battery Replacement
Initial start-up requires the removal of the
battery pull-tab.
To replace the battery, press on the
retaining lug of the battery holder at the
bottom of the remote and pull out the
holder.
1
4
2
TEST OFFON
5
3
6
+-
7
AUTO
10
AUTO
13
16
min
8
AUTO
11
AUTO
14
17
5
10
9
AUTO
12
AUTO
15
18
SET
20
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Push the battery holder together with the
battery into the remote control until the
holder is latched in place.
The used battery must be disposed of in accordance with the
applicable regulations.
Technical Data
Transmission Method: Infrared
Range: 15m approx
Battery: 3Vdc CR2032 Lithium Button Cell
Expected Battery Life: 3 years
Storage Temperature: -25 C to +70 C
Operating Temperature: 0 C to 40 C
o o
o o
IP Rating: 40
Approval: CE
Dimensions: 87mm (h) x 40mm (w) x 7mm (d)
Weight: 20g approx
Product Compatibility
The push-buttons 1-6 (On, Brighten, Set Light Level, Dim and Walk Test) will work with
almost all current IR-enabled Ex-Or detectors.
The programming buttons 7-18 can be used with the following part numbers:
MS1200D(AL)Ix
MS1200PF
MS1201Px
MS2001Ax
MS2000D(ALI)F
MS2001D(ALI)x
MSB100xD(ALI)T
MSB100xPT
MS2000D(ALI)F
MSM2000D(ALI)
x denotes any other character/s in the part number
by Honeywell
HP18 LightSpot Programmer
1
2
3
TEST OFFON
5
4
6
+-
7
8
AUTO
AUTO
10
11
AUTO
AUTO
13
14
16
17
5
min
SET
9
AUTO
12
AUTO
15
18
10
20
Ex-Or
Novar ED&S Limited
Haydock Lane, Haydock, Merseyside WA11 9UJ
Telephone: + 44 (0)1942 719229
Fax: + 44 (0)1942 508753
Email: technicalsales.ex-or@honeywell.com
W5070D
Loading...