Exor eTOP Series 500, eTOP507M, eTOP510, eTOP506, eTOP504 Operating Instructions Manual

...

Download

Page 1

eTOP Series 500

Operating Instructions

User’s Manual for eTOP Series 500 Touchscreen Products

Page 2

Copyright © 2018 Exor International S.p.A. – Verona, Italy Subject to change without notice The information contained in this document is provided for informational purposes only. While efforts were made to verify the accuracy of the information contained in this documentation, it is provided “as is” without warranty of any kind. Third-party brands and names are the property of their respective owners. www.exorint.com

Page 3

Table of Contents

Introduction 4

Safety guide 5

1 Product overview 6

2 Standards and approvals 7

3 Technical specications 8

4 Technical data 10

4.1 Dimensions 14

4.2 Installation environment 16

4.3 Installation procedure 17

5 Connections 18

5.1 Serial port 20

5.2 Ethernet port 21

5.3 Option plugin module 22

6 Power supply, grounding and shielding 24

7 Battery 25

8 Cleaning faceplates 26

9 Getting started 26

10 System settings 27

11 LED indicator on front panel 30

12 Unpacking and packing Instructions 31

Page 4

Introduction

The operational guidelines described below is information which relates to the device, installation, transportation, storage, assembly, use and maintenance.

This Operating Instruction describes the main features of the operator panels. The Guide refers to the following models:

eTOP504 Operator interface with TFT color 4,3” display touchscreen eTOP506 Operator interface with TFT color 5.7” display touchscreen eTOP507 Operator interface with TFT color 7” widescreen display touchscreen eTOP507M Operator interface with TFT color 7” widescreen display touchscreen, 1GHz CPU eTOP510 Operator interface with TFT color 10.4” display touchscreen eTOP512 Operator interface with TFT color 12.1” display touchscreen eTOP513 Operator interface with TFT color 13.3” widescreen display touchscreen eTOP515 Operator interface with TFT color 15” display touchscreen

Page 5

Safety Guide

The manual contains safety standards that must be respected for the personal safety and to avoid damage. Indications of attention are divided into three levels of severity:

DANGER: indicates a failure to observe safety rules and such failure may cause death or serious injuries.

ATTENTION: indicates a failure to observe safety rules and that deciency may cause damage.

CAUTION: indicates a failure to observe safety rules and that deciency may cause defects to the equipment

or inconsistencies.

CAUTION

ATTENTION

DANGER



Page 6

1 Production Overview

The Exor eTOP Series 500 HMI products combine state-of-the-art features and top performance with an oustanding design. They are the ideal choice for all demanding HMI applications including factory and building automation.

The eTOP Series 500 HMI panels have been designed to run the JMobile software.

• Designed for use with JMobile HMI software.

• Full vector graphic support. Native support of SVG graphic objects. Trasparency and alpha

blending.

• Full object dynamics: control visibility and transparency, move, resize, rotate any object on screen.

Change properties of basic and complex objects.

• TrueType fonts.

• Multilanguage applications. Easily create and manage your applications in multiple languages to meet global requirements. Far East languages are supported. Tools available in JMobile Studio

support easy third-party translations and help reducing development and maintenance costs of the application.

• Data display in numerical, text, bargraph, analog gauges and graphic image formats.

• Rich set of state-of-the-art HMI features: data acquisition, alarm handling, scheduler and timed

actions (daily and weekly schedulers, exception dates), recipes, users and passwords, RSS feeds, rotating menus.

• Includes support for a wide range of communication drivers for Factory systems.

• Multiple drivers communication capability.

• Remote monitoring and control. Client-Server functionality.

• On-line and Off-line simulation with JMobile Studio.

• Powerful scripting language for automating HMI applications. Script debugging improves efciency

in application development.

• Rich gallery of vector symbols and objects.

• Optional plug-in modules for eldbus systems, I/O and controllers.

Page 7

2 Standards and Approvals

The products have been designed for use in an industrial environment in compliance with the 2014/30/

EU EMC Directive. The products have been designed in compliance with: EN 61000-6-4 EN 55011 Class A

EN 61000-6-2 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6

The installation of these devices into the residential, commercial and light-industrial environments is allowed only in the case that special in measures are taken in order to ensure conformity to EN 61000-6-3.

The products are in compliance with the Restrictions on Certain Hazardous Substances (RoHS) Directive

2011/65/EU

In compliance with the above regulations the products are CE marked.

Product Identication

The product may be identied through a plate attached to the rear cover. You will have to know the type

of unit you are using for correct usage of the information contained in the guide.

An example of this plate is shown in the gure below:

eTOP504 product model name ETOP504U1P1 product part number

1846 year/week of production

AA00001HP123456789AA serial number 040100A15011000 version id of the product

Page 8

3 Technical Specications

Touch screen technology Resistive

Back-up battery

3V 50mAh Lithium, rechargeable, not user-replaceable,

model VL2330. Fuse Automatic

Serial Port

RS-232, RS-485, RS-422 software congurable

User memory Flash 128MB for eTOP504, 506, 507 Flash 256MB for eTOP507M, eTOP510, 512, 513, 515

Recipe memory Flash Hardware clock Clock/Calendar with back-up battery Accuracy RTC (at 25°C operating) <100ppm

Environmental conditions

Operating temperature (vertical 0 ÷ +50°C EN 60068-2-14 installation) Storage temperature -20 ÷ +70°C EN 60068-2-14 Operating and storage humidity 5 ÷ 85 % RH not-condensing EN 60068-2-30 Vibrations 5 ÷ 9 Hz, 7 mm

p-p

EN 60068-2-6

9 ÷ 150 Hz, 1 g

Shock ± 50 g, 11 ms, 3 pulses per axis EN 60068-2-27 Protection class IP66 front panel * EN 60529

* The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the “Environmental conditions”. Even though the level of resistance unit is equivalent to these standards, oils

that should have no effect on the panel can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oil are allowed to adhere to the unit for long periods of time. If the front face protection sheet on the panel becomes peeled off, these conditions can lead to the ingress of oil into the panel and separate protection measures are suggested. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed.

Electromagnetic Compatibility (EMC)

Radiated disturbance test Class A EN 55011 Electrostatic discharge immunity test 8 kV (air electrostatic discharge) EN 61000-4-2

4 kV (contact electrostatic discharge)

Radiated, radio-frequency, 80 MHz ÷ 1 GHz, 10V/m EN 61000-4-3 electromagnetic eld immunity test 1,4 GHz ÷ 2 GHz, 3 V/m

2 GHz ÷ 2.7 GHz, 1 V/m

Page 9

Burst immunity test ± 2 KV DC power port EN 61000-4-4 ± 1 KV signal line Surge immunity test ± 0,5 KV DC power port (line to earth) EN 61000-4-5 ± 0,5 KV DC power port (line to line) ± 1 KV signal line (line to earth)

Immunity to conducted disturbances inducted by radiofrequency eld 0.15 ÷ 80 MHz, 10V EN 61000-4-6

Voltage dips, short interruptions and voltage variations immunity test Port: AC mains; Level:

100% duration: 1 cycle and 250 cycles (50Hz); 40% duration: 10 cycles (50Hz); 70% duration: 25 cycles (50Hz); Phase: 0°-180° Test executed on the 230Vac side of the Exor International Power Supply EN 61000-4-11

Durability information

Backlight service life 40000 Hrs. or more (LED type) (Time of continuos operation until the brightness of the

backlight reaches 50% of the rated value when the sorrounding air temperature is 25°C) - see Note 1

Front foil 10 years if the surrounding air temperature is 25°C (without directly exposure to sunlight or UV ray)

UV Resistance Indoor applications: After 300 hours cycled humidity in

QUV accelerated weathering, some yellowing and brittleness may be present. - see Note 2.

Touch screen reliability > 1 milion operations

Note 1: Extended use in environments where the surrounding air temperature is 40°C or higher may degrade

backlight quality/reliability/durability.

Note 2: Solvent resistance:

Contact for 1/2 hour at 21°C, No visible effect: Acetone, Butyl Cellosolve, Cyclohexanone, Ethyl Acetate,

Hexane, Isopropyl Alcohol, MEK, Methylene Chloride, Toluene, Xylene Contact for 24 hours at 49°C, No visible effect: Coffee, Ketchup, Lemon Juice, Mustard (slight yellow stain), Tea, Tomato juice.

3 Technical Specications

Page 10

4 Technical Data

Model eTOP504 eTOP506

Display / Backlight

TFT Color / LED TFT Color / LED

Colors

64K 64K

Resolution

480x272 320x240

Diagonal (inches)

4.3” 5.7”

Dimming

yes yes

User memory Flash

128 MB 128 MB

SD card slot

yes yes

Recipe memory

Yes. Flash memory storage limited only by

available memory

Yes. Flash memory storage limited only by

available memory

Serial Port

RS-232, RS-485, RS-422

DB9 female software congurable

RS-232, RS-485, RS-422

DB9 female software congurable

Ethernet port

2 10/100 Mbit with integrated switch 2 10/100 Mbit with integrated switch

USB port

1 Host interface version 2.0 and version

1.1

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

Expansion slot

1 Optional Plugin 2 Optional Plugin

Battery

rechargeable rechargeable

Real Time Clock

yes yes

Voltage

18-32VDC (*) 18-32VDC (*)

Current rating (at 24VDC)

0.4A 0.65A

Weight

1 Kg 1 Kg

(*) For applications requiring compliance with EN 61131-2 and specically in reference to 10 ms voltage dips, the

minimum power supply voltage is 18Vdc,

Page 11

4 Technical Data

Model eTOP507 eTOP507M

Display / Backlight

TFT Color / LED TFT Color / LED

Colors

64K 64K

Resolution

800x480 800x480

Diagonal (inches)

7” widescreen 7” widescreen

Dimming

yes yes

User memory Flash

128 MB 256 MB

SD card slot

yes yes

Recipe memory

Yes. Flash memory storage limited only by

available memory

Yes. Flash memory storage limited only by

available memory

Serial Port

RS-232, RS-485, RS-422

DB9 female software congurable

RS-232, RS-485, RS-422

DB9 female software congurable

Ethernet port

2 10/100 Mbit with integrated switch 2 10/100 Mbit with integrated switch

USB port

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

Expansion slot

2 Optional Plugin 2 Optional Plugin

Battery

rechargeable rechargeable

Real Time Clock

yes yes

Voltage

18-32VDC (*) 18-32VDC (*)

Current rating (at 24VDC)

0.65A 0.7A

Weight

1 Kg 1 Kg

(*) For applications requiring compliance with EN 61131-2 and specically in reference to 10 ms voltage dips, the

minimum power supply voltage is 18Vdc,

Page 12

4 Technical Data

Model eTOP510 eTOP512

Display / Backlight

TFT Color / LED TFT Color / LED

Colors

64K 64K

Resolution

800x600 800x600

Diagonal (inches)

10.4” 12.1”

Dimming

yes yes

User memory Flash

256 MB 256 MB

SD card slot

yes yes

Recipe memory

Yes. Flash memory storage limited only by

available memory

Yes. Flash memory storage limited only by

available memory

Serial Port

RS-232, RS-485, RS-422

DB9 female software congurable

RS-232, RS-485, RS-422

DB9 female software congurable

Ethernet port

2 10/100 Mbit with integrated switch 2 10/100 Mbit with integrated switch

USB port

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

Expansion slot

2 Optional Plugin 2 Optional Plugin

Battery

rechargeable rechargeable

Real Time Clock

yes yes

Voltage

18-32VDC (*) 18-32VDC (*)

Current rating (at 24VDC)

1A 1.2A

Weight

2.1 Kg 2.8 Kg

(*) For applications requiring compliance with EN 61131-2 and specically in reference to 10 ms voltage dips, the

minimum power supply voltage is 18Vdc,

Page 13

4 Technical Data

Model eTOP513 eTOP515

Display / Backlight

TFT Color / LED TFT Color / LED

Colors

64K 64K

Resolution

1280x800 1024x768

Diagonal (inches)

13.3” widescreen 15”

Dimming

yes yes

User memory Flash

256 MB 256 MB

SD card slot

yes yes

Recipe memory

Yes. Flash memory storage limited only by

available memory

Yes. Flash memory storage limited only by

available memory

Serial Port

RS-232, RS-485, RS-422

DB9 female software congurable

RS-232, RS-485, RS-422

DB9 female software congurable

Ethernet port

2 10/100 Mbit with integrated switch 2 10/100 Mbit with integrated switch

USB port

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

2 Host interface, 1 version 2.0,

1 version 2.0 and 1.1

Expansion slot

2 Optional Plugin 2 Optional Plugin

Battery

rechargeable rechargeable

Real Time Clock

yes yes

Voltage

18-32VDC (*) 18-32VDC (*)

Current rating (at 24VDC)

1.2A 1.4A

Weight

2.8 Kg 3.5 Kg

(*) For applications requiring compliance with EN 61131-2 and specically in reference to 10 ms voltage dips, the

minimum power supply voltage is 18Vdc,

Page 14

4.1 Dimensions

4 Technical Data

MODEL A B C

D E F

eTOP504 149mm/5.86” 109mm/4.29” 136mm/5.35” 96mm/3.78” 56mm/2.40” 4mm/0.16”

Page 15

4.1 Dimensions

4 Technical Data

MODEL A B C

D E F

eTOP506 187mm/7.36” 147mm/5.79” 176mm/6.90” 136mm/5.35” 47mm/1.85” 4mm/0.16”

eTOP507 187mm/7.36” 147mm/5.79” 176mm/6.90” 136mm/5.35” 47mm/1.85” 4mm/0.16”

eTOP507M 187mm/7.36” 147mm/5.79” 176mm/6.90” 136mm/5.35” 47mm/1.82” 4mm/0.16”

eTOP510 287mm/11.30” 232mm/9.13” 276mm/10.86” 221mm/8.70” 56mm/2.20” 4mm/0.16”

eTOP512 336mm/13.22” 267mm/10.51” 326mm/12.83” 256mm/10.07” 56mm/2.20” 4mm/0.16”

eTOP513 336mm/13.22” 267mm/10.51” 326mm/12.83” 256mm/10.07” 56mm/2.20” 4mm/0.16”

eTOP515 392mm/15.43” 307mm/12.08” 381mm/15” 296mm/11.65” 60mm/2.36” 4mm/0.16”

Page 16

The equipment is not intended for continuous exposure to direct sunlight. This might accelerate the aging process of the front panel lm.

The equipment is not intended for installation in contact with corrosive chemical compounds. Check the resistance of the front panel lm to a specic compound before installation.

Do not use tools of any kind (screwdrivers, etc.) to operate the keyboard of the panel or the touch screen.

In order to meet the front panel protection classications, proper installation procedure must be followed:

• the borders of the cutout must be flat

• screw up each xing screw until the plastic bezel corner get in contact with the panel.

• the cutout for the panel must be of the dimensions indicated in this manual.

The IP66 is guaranteed only if:

• max deviation from the plane surface to the cut-out: O0.5mm

• thickness of the case where is mounted the equipment: from 1,5mm to 6mm

• max surface roughness where the gasket is applied: O120 um

Applying the rectangular gasket

The gasket should be applied on the rear of the frame.

A. Gasket B.

Installation cut-out

4 Technical Data

4.2 Installation Environment

Fig. 4.1: eTOP504, eTOP506, eTOP507, eTOP507M

Fig. 4.2: eTOP510, eTOP512, eTOP513, eTOP515

Page 17

4.3 Installation Procedure

Place the xing brackets as shown in gure (Fig. 4.3).

Fig. 4.3

4 Technical Data



CAUTION

Screw each xing screw until the bezel corner gets in contact with the panel

Page 18

1. Serial Port

2. 2x Ethernet Port

3. USB Port

4. Power Supply

5. Expansion slot for Plugin module

6. SD Card Slot

Fig. 5.1 - eTOP504

5 Connections

Page 19

1. Serial Port

2. 2x Ethernet Port

3. USB Port (version 2.0 - 1.1)

4. USB Port (version 2.0 High speed only)

5. Power Supply

6. 2x Expansion slot for Plugin module

7. SD Card Slot

Fig. 5.2 - eTOP5xx

5 Connections

Page 20

The serial port is used to communicate with the PLC or with another type of controller. Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422, RS-485.

Pin Description

1 GND 2 3 CHA 4 CHB 5 6 +5V output 7 CHB+ 8 CHA+ 9

The serial port is software programmable. Make sure you select the appropriate interface in the programming software.

The communication cable must be chosen for the type of device being connected.

SERIAL PORT

Pin Description

1 GND 2 3 TX 4 RX 5 6 +5V output 7 CTS 8 RTS 9

RS-232

RS-422, RS-485

5 Connections

5.1 Serial Port

Page 21

1 8

ON: No activity BLINKING: Activity

5 Connections

5.2 Ethernet Port

The Ethernet port have two status indicators. Please see description in gure.

OFF: Valid link has NOT been detected ON: Valid link has been detected

Page 22

5 Connections

5.3 Optional plugin module

eTOP500 serie panels have several optional plugin module, multiple modules congurations are possible.

Slot#2 and Slot#4 are available only if plugin module has the “bus extension connector”.

Each slot carries three communication channels:

• 1 serial interface

• 1 CAN interface

• 1 SPI interface

Note: It is not possible to stack two modules that are using the same type of interface.

Page 23

Below you can nd relation between modules and max number of modules that can be used into eTOP500

serie panels, based on their Interface Type:

Module Application Max Modules Interface Type Bus Extension

connector

PLCM01 CAN 1 for eTOP50x

2 for eTOP51x

CAN Y

PLCM01-NE CAN 1 for eTOP50x

2 for eTOP51x

CAN N

PLCM02 KNX 1 Serial N

PLCM03 Serial RS232 2 Serial Y

PLCM04 Serial RS485 2 Serial Y

PLCM05 CODESYS V2

License

1 Y

PLCM06 Probus DP 1 SPI N

PLIO03 Multifunction I/O 1 SPI N

PLIO06 Compact I/O 2 SPI N

Max modules refers to max number of modules can be plugged into the HMI (all slots),

If you are planning to use PLCM03 and PLCM04 (additional serial ports) you will obtain following “COM Slot#” association:

• a module plugged in Slot#1 or into Slot#2 will be COM2,

• a module plugged in Slot#3 or into Slot#4 will be COM3.

If you are planning to use two PLCM01 (CAN interface) you will obtain following Slot# association:

• a module plugged in Slot#1 or into Slot#2 will be the CanPort 0,

• a module plugged in Slot#3 or into Slot#4 will be the CanPort 1.

5 Connections

Page 24

The power supply terminal block is shown in the gure below.

The unit must always be grounded to earth. Grounding helps limit the effects of noise due to electromagnetic interference on the control system.

Earth connection will have to be done using either the screw or the faston terminal located near the power supply terminal block. A label helps identify the ground connection. Also connect to ground the terminal 3 on the power supply terminal block.

The power supply circuit may be floating or grounded. In the latter case, connect to ground the power

source common as shown in gure (see below) with a dashed line.

When using the floating power scheme, note that the panes internally connects the power common to

ground with a 1MΩ resistor in parallel with a 4,7nF capacitor.

The power supply must have double or reinforced insulation. The suggested wiring for the power supply is shown below.

Fig. 6.2

All the electronic devices in the control system must be properly grounded. Grounding must be performed according to applicable regulations.

Fig. 6.1 - Power supply terminal block

6 Power Supply, Grounding and Shielding

Note: Ensure that the power supply has enough power capacity for the operation of the equipment.

Page 25

These devices are equipped with rechargeable Lithium battery, not user-replaceable.

The following information is maintained by the battery:

• hardware real-time clock (date and time)

Charge:

At rst installation must be charged for 48 hours.

When the battery is fully charged, it ensures a period of 3 months of data back-up at 25°C.

ATTENTION

Dispose of batteries according to local regulations.

7 Battery

Battery

Fig. 7.1: eTOP504

Fig. 7.2: eTOP506, eTOP507,

eTOP507M, eTOP510, eTOP512, eTOP513, eTOP515

Battery

Page 26

The equipment must be cleaned only with a soft cloth and neutral soap product. Do not use solvents.

eTOP Series 500 HMI products must be programmed with the software JMobile Studio. JMobile Studio is a software tool that must be properly installed on a computer running Microsoft Windows.

There are two options to transfer a JMobile application project to a HMI device: Ethernet Connect the HMI device to the computer with an Ethernet network connection. From

JMobile Studio choose the command Run/Download to target. You may have to ensu re that the proper rewall policy has been congured in the computer to allow JMobile

Studio to access the network. USB or SD Create an Update Package using JMobile Studio and copy it to a USB Flash drive or to an SD memory card.

8 Cleaning faceplates

9 Getting Started

Page 27

10 System Settings

eTOP Series 500 HMI products have a system settings tool to allow conguration of system options. The user interface of System Settings tool is based on a rotating menu. Use navigation buttons Next/

Back to scroll through the available options.

The active item is highlighted on the left side. The info pane on the right side shows relevant information, when applicable. Touch the active item to start the associated function.

System Settings has two modes of operation:

User Mode JMobile runtime is running or the HMI device is in “factory default” status. System Mode JMobile runtime is not running or the HMI device has a software failure.

System Mode includes all options available in User Mode and offers in additions commands dedicated to system upgrade and recovery.

Activation of System Settings in User Mode:

Factory default status Press “System Setting” button on the HMI screen JMobile runtime running Recall context menu and select “System Settings”. To recall the context menu click and hold any unused area of the touchscreen for a few seconds. Default hold time is 2 seconds.

Page 28

Activation of Systems Settings System Mode:

Normal operation If JMobile runtime is not running: Press “System Settings” button on the HMI screen. If JMobile runtime is running: recall context menu, select “System Settings”

Select the Restart option then choose the “Conguration OS” option.

Note: To recall the context menu click and hold any unused area of the touchscreen for a few seconds. Default hold time is 2 seconds.

Recovery operation If panel is not responsive, use the so-called “tap-tap” procedure. This procedure consists in tapping the surface of the touchscreen during the

device power-up phase. Tapping frequency must be high. You have to start

tapping the touchscreen as soon as power has been applied to the device.

When the sequence has been recognized, the system shows the message: “Tap Tap detected, Going to Cong Mode” on the screen.

User Mode includes options for basic settings of the device.

Calibrate Touch calibrate the touchscreen interface Plugin list show if optional plug-in modules are installed Network congure IP Address of Ethernet interface BSP settings show the BSP (Board Support Package) version, check the operating hours

for the device and for the display backlight, manage the buzzer

Time change the device date and time, including time zone, Daylight Saving Time and NTP Server

Regional Settings customize Windows Regional Settings, such as date format Display settings congure automatic backlight turnoff and adjust brightness Close close System Settings Restart restart the device. “Main OS” option restarts as per default, “Conguration

OS” option restart panel directly into System Settings in System Mode

System Mode is the complete interface of the System Settings tool where all functions are available, in addition to the options available in “User Mode”.

Format Flash allows to format internal device Flash disk. All projects, the Runtime and System settings will be deleted, returning the device to factory condition. Restore Factory Settings restore factory settings with choice of what to delete. Can be used as alternative to Format Flash. Options available are:

Uninstall HMI removes the Runtime and all projects. Clear system settings reset the system parameters like IP Address,

date/time, etc

Clear Controller Application remove CODESYS application

10 System Settings

Page 29

10 System Settings

Resize Image Area reserved to authorized technical personnel

Download Conguration OS update the Conguration OS module of BSP

Download Main OS update the Main OS module of BSP Download Splash Image replace the splash screen image displayed by the device at power-

up; the image must be supplied in the appropriate binary format. We recommend changing the splash screen image with the use of JMobile Studio

Download OS Partition reserved to authorized technical personnel Download Data Partition reserved to authorized technical personnel Download Disk Image reserved to authorized technical personnel Download Bootloader update the Bootloader module of BSP Upload Bootloader reserved to authorized technical personnel

Upload Conguration OS reserved to authorized technical personnel

Upload Main OS reserved to authorized technical personnel Upload Splash Image copy to an USB Memory or SD Card the current splash screen image

in binary format

Upload OS Partition reserved to authorized technical personnel Upload Data Partition reserved to authorized technical personnel Upload Disk-Image copy to an USB Memory or SD Card the content of whole Flash disk

in binary format

Only for eTOP507M, eTOP510, eTOP512, eTOP513 and eTOP515 System Mode includes also:

Download Main FPGA update the Main FPGA module of BSP Download Safe FPGA update the Safe FPGA module of BSP Download System Supervisor update the System Supervisor module of BSP Upload Main FPGA reserved to authorized technical personnel Upload Safe FPGA reserved to authorized technical personnel Upload System Supervisor reserved to authorized technical personnel

Page 30

11 LED Indicator on Front Panel

The table below shows the symbol of the LED indicator dedicated to special functions.

Page 31

To repack the unit, please follow the instructions backwards.

12 Unpacking and packing instructions

Exor eTOP Series 500, eTOP507M, eTOP510, eTOP506, eTOP504 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual