For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
M216H/ M216HSP
For Serial Nos.
370,000 & Higher
CONGRATULATIONS on the purchase of your new Exmark mower. This product has been carefully designed and manufactured to give
you a maximum amount of dependability and years of trouble--free operation. If additional information is needed, or should you require trained
mechanic service, contact your authorized Exmark equipment dealer or distributor. If you need to order replacement parts from your dealer,
always give the model number and serial number of your mower as well as the part number, description and quantity of the part needed.
The Serial No. plate is located on the top of the mower deck on the right hand corner of the machine. For ease of ordering and reference,
we suggest that you record the information requested in the following identification table.
Place Model No. and Serial No. Label Here
(Included in Literature Pack)
or Fill in Below
Model No.
Serial No.
Engine Model No. and Spec. No. (Code)
Engine Serial No (E/No)
Date Purchased
Part No. 3327-672
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
IMPORTANT
When the mower is used or operated on any California forest-, brush- or
grass-covered land, a working spark arrester must be attached to the muffler. If not,
the operator is violating state law, Section 4442 Public Resource Code. To acquire
a spark arrester for your unit, see your Engine Service Dealer.
WARNING
POTENTIAL HAZARD
• This product is a piece of power equipment.
WHAT CAN HAPPEN
• Failure to follow safe operating practices can result in serious operator injury or
even death.
HOW TO AVOID THE HAZARD
• Keep all shields, guards, and safety devices (especially the grass discharge
system) in place and in proper working condition.
• Before adjusting, servicing, or performing maintenance, stop the engine and wait
for all moving parts to stop, then remove the spark plug wire or remove the key.
• If the mower deck becomes clogged, stop the engine and wait for all moving
parts to stop, then remove the spark plug wire or remove the key before cleaning
the blockage.
• Keep hands, feet, and clothing away from power-driven parts.
• Keep off the mower unless the seat platform is provided.
• Keep others off the mower.
WARNING
POTENTIAL HAZARD
• Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors has
caused cancer in laboratory animals.
WHAT CAN HAPPEN
• Failure to use caution may cause serious injury or illness.
HOW TO AVOID THE HAZARD
• Avoid prolonged breathing of vapors.
• Keep face away from nozzle and gasoline tank/container opening.
• Keep gasoline away from eyes and skin.
• Never siphon gasoline by mouth.
Exmark reserves the right to make changes to add improvements to its products at any time without
incurring any obligation to make such changes to products manufactured previously. Exmark, or its
distributors and dealers, accept no responsibility for variations which may be evident in the actual
specifications of its products and the statements and descriptions contained in this publication.
ii
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
EXMARK PARTS PLUS PROGRAM
EFFECTIVE DATE: September 1,1995
Program
If your Exmark dealer does not have the Exmark part in
stock, Exmark will get the parts to the dealer the next
business day or the part will be FREE* Guaranteed!!
How the Program Works
1. If dealer does not have part in stock for a
”down” unit at the time of request by customer,
the dealer contacts his distributor by 1:00 p.m.
local time, and requests Exmark Parts Plus
shipment of six line items or less.
2. Distributor ships part(s) to dealer or customer,
as requested by dealer, same day, overnight
UPS Distributor bills dealer for part and freight
charges where applicable.
3. If distributor does not have the part(s) in stock to satisfy Exmark Parts Plus order, he contacts Exmark by 3:00 p.m.,
central time, with an Exmark Parts Plus
4. If order is received by 3:00 p.m. central time, Exmark ships part(s) direct to dealer or customer, as requested by distributor,
same day, overnight UPS, Exmark bills the distributor for parts and shipping charges, where applicable.
5. The customer pays for the part
the program.
6. Who pays for the part
A. Under any circumstance the customer does not pay.
B. If the part does not arrive overnight due to:
1. The dealer not submitting the Exmark Parts Plus
the part and freight.
2. The Distributor being unable to ship the part the same day or not submitting the Exmark Parts Plus
Exmark by 3:00 p.m. central time, the Distributor pays for the part and freight.
3. Exmark being unable to ship the part and the Exmark parts order is received by 3:00 p.m. central time, Exmark
pays for the part and freight.
4. If the part does not arrive overnight due to the shipper (UPS), the shipper pays for the freight and Exmark pays for
the part.
The following restrictions apply –– The Exmark Parts Plus
applies only to orders submitted on this program Monday through Thursday. Parts Plus service is available only in the 48 contiguous United States.
UPS has initiated a Saturday delivery program to many areas of the continental United States and can be requested for an overnight shipment on
Friday to be delivered Saturday. The next day air charge, plus the Saturday delivery fee will be the responsibility of the purchaser. Exmark Mfg. will
assume no responsibility for Saturday delivery shipments. To qualify, all Exmark Parts Plus orders must be received by Exmark by 3:00 p.m.
central time. Orders must be six line items or less. Exclusions from the Exmark Parts Plus Program are: Any wholegood or accessory in its entirety,
engines and engine replacement parts, 5–speed Peerless transmissions and 5–speed transaxles, hydraulic or hydrostatic wheel motors, cutter decks
and engine decks or any item exceeding United Parcel Service size and weight restrictions.
and freight if it fails to arrive overnight in accordance to the program?
and freight if it is shipped under the Exmark Parts Plus and if it arrive in accordance to
order of six line items or less.
order to his Exmark distributor by 1:00 p.m., the dealer pays for
Program is available only through participating Exmark Dealers and
order to
Due to UPS restrictions, aerosol spray paint is considered a hazardous material and cannot be shipped via UPS next day or Second Day Air.
Exmark Manufacturing stocks a limited supply of parts for transaxles, pumps and wheel motors. These parts can be ordered for Next Day Air shipment but will not be guaranteed per the Parts Plus Program.
www.mymowerparts.com
iii
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully
designed and manufactured to give you a maximum amount of dependability and years of trouble-free
operation.
OPERATOR’S MANUAL
This manual contains assembly, operating, maintenance, adjustment and safety instructions for
your Exmark mower.
BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY.
By following the operating, maintenance and safety instructions, you will prolong the life of your
mower, maintain its maximum efficiency and promote safe operation.
If additional information is needed, or should you require trained mechanic service, contact your
authorized Exmark equipment dealer or distributor.
All Exmark equipment dealers and distributors are kept informed of the latest methods of servicing
and are equipped to provide prompt and efficient service in the field or at their service stations. They
carry ample stock of service parts or can secure them for you from the factory.
All Exmark parts are thoroughly tested and inspected before leaving the factory; however, attention
is required on your part if you are to obtain the fullest measure of satisfaction and performance.
iv
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
This spark ignition system complies with Canadian
ICES-002.
Ce système d’allumage par étincelle de véhicule est
conforme à la norme NMB-002 du Canada.
The enclosed Engine Owner ’s Manual is supplied for
information regarding The U.S. Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance
and warranty.
Keep this engine Owner ’s Manual with your unit.
Should this engine Owner’s Manual become damaged
or illegible, replace immediately. Replacements may be
ordered through the engine manufacturer.
Contents
Page
Specifications 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 2. . . . . . . . . . . . . . . . . . .
Exmark Lawn Mower Safety 3. . . . . . . . . . . . . . . .
Safety and Instruction Decals 4. . . . . . . . . . . . . . .
Assembly 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loose Parts 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Handle 6. . . . . . . . . . . . . . . . . . . . . .
Installing the Starter Rope 6. . . . . . . . . . . . . . . . . .
Installing the Discharge Tunnel Plug 6. . . . . . . . . .
Before Starting 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling the Crankcase with Oil 7. . . . . . . . . . . . . . .
Filling the Fuel Tank with Gasoline 7. . . . . . . . . .
Reviewing the Maintenance Schedule 8. . . . . . . . .
Operation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the Engine 9. . . . . . . . . . . . . . . . . . . . . . . .
Stopping the Engine 9. . . . . . . . . . . . . . . . . . . . . . .
Using the Self-propel Drive 10. . . . . . . . . . . . . . . . .
Using the Discharge Tunnel Plug 10. . . . . . . . . . . .
Adjusting the Cutting Height 10. . . . . . . . . . . . . . . .
Using the Grass Bag 11. . . . . . . . . . . . . . . . . . . . . . .
Operating Tips 12. . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Maintenance Schedule 14. . . . . . . .
Checking the Engine Oil Level 15. . . . . . . . . . . . . .
Cleaning under the Housing 15. . . . . . . . . . . . . . . .
Cleaning the Discharge Tunnel and Plug 16. . . . . .
Servicing the Air Cleaner 16. . . . . . . . . . . . . . . . . .
Maintaining the Blade 17. . . . . . . . . . . . . . . . . . . . .
Cleaning under the Belt Cover 18. . . . . . . . . . . . . .
Lubricating the Pivot Arms 19. . . . . . . . . . . . . . . . .
Page
Adjusting the Self-propel Drive 19. . . . . . . . . . . . . .
Changing the Engine Oil 19. . . . . . . . . . . . . . . . . . .
Servicing the Spark Plug 20. . . . . . . . . . . . . . . . . . .
Lubricating the Gear Case 20. . . . . . . . . . . . . . . . . .
Adjusting the Blade Brake Cable 20. . . . . . . . . . . .
Servicing the Wheels 21. . . . . . . . . . . . . . . . . . . . . .
Storage 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparing the Fuel System 22. . . . . . . . . . . . . . . . . .
Preparing the Engine 22. . . . . . . . . . . . . . . . . . . . . .
General Information 22. . . . . . . . . . . . . . . . . . . . . . .
Removing the Lawn Mower from Storage 22. . . . .
Accessories 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Warranty
Exmark Commercial Turf Equipment 26. . . . . . . . . .
Specifications
Model Number: M216H, M216HSP
Engine: Honda 5.5 HP OHV
3350 RPM (No load)
Fuel System:
Capacity: 2.1 qt. (2.0 L)
Transmission (M216HSP):
3 speeds forward
Speed range:
First 2.2 mph (3.5 km/h)
Second 3.2 mph (5.2 km/h)
Third 4.5 mph (7.3 km/h)
Cutting Width: 21 in. (53 cm)
Cutting Height:
Adjusts in 0.5 in. (1.3 cm) increments from
.75 in. (1.9 cm) to 3.25 in. (8.3 cm)
Grass Catcher Capacity 2.5 Bu. (88 L)
Weight (with bag):
M216H 96 lb. (44 kg)
M216HSP 108 lb. (49 kg)
Introduction
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Exmark designs and produces safe
products, you are responsible for operating the product
properly and safely.
1
www.mymowerparts.com
All Rights Reserved
Printed in the USA
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
This manual identifies potential hazards and has special
safety messages that help you and others avoid personal
injury and even death. Danger, Warning, and Caution are
signal words used to identify the level of hazard.
However, regardless of the hazard, be extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if you do not follow the recommended
precautions.
Warning signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Caution signals a hazard that may cause minor or
moderate injury if you do not follow the recommended
precautions.
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note: emphasizes general
information worthy of special attention.
Safety
This lawn mower meets or exceeds the CPSC blade
safety requirements for walk-behind rotary lawn
mowers and the B71.4 specifications of the American
National Standards Institute in effect at the time of
production.
Warning
Engine exhaust contains carbon monoxide, an
odorless, deadly poison that can kill you.
Training
• Read the Operator ’s Manual and other training
material. If the operator(s) or mechanic(s) can not read
English it is the owner’s responsibility to explain this
material to them.
• Become familiar with the safe operation of the
equipment, operator controls, and safety signs.
• All operators and mechanics should be trained. The
owner is responsible for training the users.
• Never let children or untrained people operate or
service the equipment. Local regulations may restrict
the age of the operator.
• The owner/user can prevent and is responsible for
accidents or injuries occurring to themselves, other
people, or property.
Preparation
• Only use accessories and attachments approved by the
manufacturer.
• Wear appropriate clothing including hard hat, safety
glasses, and ear protection. Long hair, loose clothing
or jewelry may get tangled in moving parts.
• Inspect the area where the equipment is to be used and
remove all objects such as rocks, toys and wire which
can be thrown by the machine.
• Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
– Use only an approved container.
Do not run the engine indoors or in an enclosed
area.
To ensure maximum safety and best performance, and
to gain knowledge of the product, it is essential that
you and any other operator of the lawn mower read
and understand the contents of this manual before the
engine is ever started.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Improperly using or maintaining this lawn mower
could result in injury or death. To reduce this potential,
comply with the following safety instructions.
Safe Operating Practices
The following instructions are from the ANSI/OPEI
B71.4–1999 standard.
– Never remove gas cap or add fuel with engine
running. Allow engine to cool before refueling. Do
not smoke.
– Never refuel or drain the machine indoors.
• Check that operator ’s presence controls, safety
switches and shields are attached and functioning
properly. Do not operate unless they are functioning
properly.
Operation
• Never run an engine in an enclosed area.
• Only operate in good light, keeping away from holes
and hidden hazards.
• Only start engine from the operator ’s position.
• Be sure of your footing, especially when backing up.
Walk, don’t run. Never operate on wet grass. Reduced
footing could cause slipping.
2
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
• Slow down on hillsides. Be sure to travel side to side
on hillsides. Turf conditions can affect the machine’s
stability. Use caution while operating near drop-offs.
• Do not change the engine governor setting or
overspeed the engine.
• Stop on level ground and shut off engine before
leaving the operator ’s position for any reason
including emptying the catcher or unclogging the
chute.
• Stop equipment and inspect blade after striking objects
or if an abnormal vibration occurs. Make necessary
repairs before resuming operations.
• Keep hands and feet away from the cutting units.
• Look behind and down before backing up to be sure of
a clear path.
• Keep pets and bystanders away.
• Slow down and use caution when crossing roads and
sidewalks.
• Stop blade if you are not mowing.
• Be aware of the mower discharge direction and do not
point it at anyone.
• Keep all parts in good working condition and all
hardware tightened. Replace all worn or damaged
decals.
Exmark Lawn Mower Safety
The following list contains safety information specific to
Exmark products or other safety information that you
must know that is not included in the ANSI/OPEI
standard.
This product is capable of amputating hands and feet, and
of throwing objects. Always follow all safety instructions
to avoid serious injury or death.
Use this product only for cutting and mulching grass, or,
when equipped with a grass bagger, for catching cut grass.
• Stop the lawn mower if anyone enters the area.
• Do not operate the lawn mower without either the
grass catcher or the guard in place.
• Do not touch the lawn mower or attachment parts
which may be hot from operation. Allow the lawn
mower to cool down before attempting to maintain,
adjust, or service it.
• Do not operate the mower under the influence of
alcohol or drugs.
• Use care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
• Do not operate the lawn mower without either the
grass catcher or the guard in place.
Maintenance and Storage
• Stop engine and disconnect spark plug wire. Wait for
all movement to stop before adjusting, cleaning or
repairing.
• Clean grass and debris from cutting unit, drive,
muffler, and engine to help prevent fires. Clean up oil
or fuel spillage.
• Let engine cool before storing and do not store near
flame.
• Shut off fuel while storing or transporting. Do not store
fuel near flames or drain indoors.
• Never allow untrained personnel to service machine.
• Remove spark plug wire before making any repairs.
• Use care when checking blade. Wrap the blade or wear
gloves, and use caution when servicing them. Only
replace blade. Never straighten or weld it.
• Keep hands and feet away from moving parts. If
possible, do not make adjustments with the engine
running.
www.mymowerparts.com
3
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any
area of potential danger. Replace any decal that is damaged or lost.
1-213242 (Self-propel model only)
74-1970 (Self-propel model only)
1. Transmission speeds 2. Neutral
39-5770
52-2610 (Hand-push model only)
52-2620 (Self-propel model only)
77-0500
82-9152
98-8017
68-7410
4
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
104-1329
Assembly
Note: Determine the left and right sides of the machine from the normal operating position.
Loose Parts
104-8585
DESCRIPTION QTY. USE
Handle
Bolts, 5/16–18 x 1-1/4 in.
Bolts, 5/16–18 x 1-1/2 in.
Carriage bolt
Washers
Locknuts
Thin nylon insert locknuts
Bag support rod
Bag aligning plate
Cap locknuts
Cable tie
1
2
2
1
4
2
2
1
1
3
1
Installing the handle
5
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Installing the Handle
1. Mount the handle to the outside of the lawn mower
housing (using the bottom hole) with two 5/16–18 x
1–1/4 in. bolts, washers, and thin nylon insert locknuts
(Fig. 1).
2
3
1
6
7
8
1. Bag support rod
2. Carriage bolt
3. Bag aligning plate
4. Cap locknuts (3)
5. Handle
6. Bolt, 5/16–18x1-1/4 in. (2)
9
Figure 1
10
7. Handle latch (2)
8. Locknut (2)
9. Bottom hole in housing
10. Washer (4)
11. Locknut (2)
12. Bolt, 5/16–18x1-1/2 in. (2)
4
5
11
12
m-3850
Installing the Starter Rope
Pull the starter rope through the rope guide on the handle
(Fig. 2).
2
1
m–210
Figure 2
1. Starter rope 2. Rope guide
Note: To make the rope easier to install, squeeze the
control bar on the handle.
Installing the Discharge Tunnel
Plug
1. Open the discharge door by pulling forward on the
handle and moving it rearward (Fig. 3). Hold the
discharge door handle to prevent the spring-loaded
door from closing while you insert the plug.
2. Secure the handle latches to the handle with two
5/16–18 x 1-1/2 in. bolts, washers, and nylon insert
locknuts (Fig. 1).
Note: You can adjust the handle height for comfortable
operation. Stand behind the handle to determine the
height. To adjust the handle height, position the bolts and
the locknuts that secure the handle latches to the handle
into the other mounting holes in the handle latches.
3. Slide the bag support rod through the bag aligning
plate and into the second from the top mounting holes
in the handle, and secure each end with a cap locknut
(Fig. 1).
4. Insert the carriage bolt through the bag aligning plate
and the top hole on the left side of the handle, and
secure it with a cap locknut (Fig. 1).
5. Use a cable tie to secure the control cables to the left
handle below the bag support rod.
1
2
m–262
Figure 3
1. Discharge door h an dl e 2. Plug rotated clockwise
2. Since the plug is slightly wider than the discharge
tunnel opening, rotate the plug clockwise slightly
while inserting it (Fig. 3).
Note: Ensure that the arrow on the plug decal points
upward.
6
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
3. Push the plug all the way in until the spring clip on the
bottom of the plug clicks into place, locking the plug
securely into the discharge tunnel (Fig. 4).
1
m–275
Figure 4
1. Spring clip
4. Release the discharge door handle to lock the top of
the plug.
To add oil:
1. Move the lawn mower to a level surface.
2. Clean around the dipstick (Fig. 5).
3. Remove the dipstick by rotating the cap
counterclockwise and pulling it out.
4. Wipe the dipstick clean with a clean cloth.
5. Insert the dipstick into the filler neck (but do not
rotate the cap clockwise to secure it), then remove it.
6. Read the oil level on the dipstick (Fig. 5).
7. If the oil level reading is below the lower limit mark
on the dipstick, remove the dipstick and slowly pour
only enough oil into the filler hole to raise the oil level
to the upper limit mark on the dipstick (Fig. 5).
Important Do not overfill the crankcase with oil and
run the engine; engine damage will result. Drain the
excess oil until the oil level reaches the upper limit mark
on the dipstick.
8. Insert the dipstick into the filler neck and rotate the
cap clockwise until it is tight.
Before Starting
Filling the Crankcase with Oil
The engine crankcase can hold 22 ounces (0.65 liters) of
oil. Use only high-quality SAE 10W–30 weight detergent
oil that has the American Petroleum Institute (API)
service classification SH, SJ, or equivalent.
Before each use, ensure that the oil level is between the
lower limit and upper limit marks on the dipstick (Fig. 5).
2
3
1. Dipstick
2. Upper limit mark
1
Figure 5
3. Lower limit mark
Filling the Fuel Tank with
Gasoline
For best results, use clean, fresh, lead-free gasoline with
an octane rating of 87 or higher. To ensure freshness,
purchase only the quantity of gasoline that you expect to
use in 30 days. Using unleaded gasoline results in fewer
combustion deposits and longer engine life.
Important Do not add oil to the gasoline.
Important Do not use methanol, gasoline containing
methanol, gasohol containing more than 10% ethanol,
premium gasoline, or white gas. Using these fuels can
damage the engine’s fuel system.
Important Do not use gasoline that is more than 30
days old.
Note: When the crankcase is empty, pour about
three-fourths of the crankcase capacity of oil in the
crankcase, then follow the procedure in this section.
www.mymowerparts.com
7
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
1. Clean around the fuel tank cap (Fig. 6).
Danger
In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.
2
1
3
• Fill the fuel tank outdoors, in an open area, and
when the engine is cold. Wipe up any gasoline
that spills.
• Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1/4 to
1/2 in. (6 to 13 mm) below the bottom of the
filler neck. This empty space in the tank allows
the gasoline to expand.
• Never smoke when handling gasoline, and stay
away from an open flame or where a spark may
ignite the gasoline fumes.
• Store gasoline in an approved fuel container
and keep it out of the reach of children.
• Never buy more than a 30-day supply of
gasoline.
Danger
When fueling, under certain circumstances, a
static charge can develop, igniting the gasoline. A
fire or explosion from gasoline can burn you and
others and damage property.
• Always place gasoline containers on the ground
and away from your vehicle before filling.
• Do not fill gasoline containers inside a vehicle
or on a truck or trailer bed because interior
carpets or plastic truck bed liners may insulate
the container and slow the loss of any static
charge.
• When practical, remove gasoline-powered
equipment from the truck or trailer and refuel
the equipment with its wheels on the ground.
• If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, not from a gasoline dispenser nozzle.
• If you must use a gasoline dispenser nozzle,
keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete.
5
6
Figure 6
1. Fuel tank cap
2. Recoil starter handle
3. Air cleaner
2. Remove the fuel tank cap.
3. Fill the fuel tank with unleaded gasoline to within 1/4
to 1/2 inch (6 to 13 mm) from the top of the tank. Do
not fill into the filler neck.
Note: The fuel tank capacity is 2.1 qt. (2.0 l).
Important Do not fill the tank more than 1/4 inch
(6 mm) from the top of the tank because the gasoline must
have room to expand.
4. Install the fuel tank cap and wipe up any spilled
gasoline.
4. Spark plug
5. Dipstick/Oil fill and drain
6. Muffler
m–6673
4
Reviewing the Maintenance
Schedule
Review the Recommended Maintenance Schedule on
page 14. You may need to perform one or more additional
procedures before or soon after you begin operating the
lawn mower.
Use a fuel stabilizer/conditioner regularly during
operation and storage. A fuel stabilizer/conditioner cleans
the engine during operation and prevents gum-like varnish
deposits from forming in the engine during periods of
storage.
Important Do not use fuel additives other than a fuel
stabilizer/conditioner. Do not use fuel stabilizers with an
alcohol base such as ethanol, methanol, or isopropanol.
www.mymowerparts.com
8
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Operation
Note: Determine the left and right sides of the machine
from the normal operating position.
Each time before you mow, ensure that the self-propel
drive and the control bar operate properly. When you
release the control bar, the engine and the blade should
stop within 3 seconds. If they do not, contact an
Authorized Service Dealer.
Caution
This machine produces sound levels in excess of
85dBA at the operator’s ear and can cause
hearing loss through extended periods of
exposure.
Wear hearing protection when operating this
machine.
Controls
The control bar, the throttle control, and the starter handle
are on the upper handle as shown in Figure 7.
2
Starting the Engine
1. Connect the wire to the spark plug (Fig. 6).
2. Open the fuel valve by moving the lever to the right
(Fig. 8).
1
Figure 8
1. Fuel valve
3. Move the throttle control to the Choke position
(Fig. 7).
Note: Do not use the choke when the engine is warm.
4. Hold the control bar to the handle (Fig. 7).
5. Pull the starter handle (Fig. 7) lightly until you feel
resistance, then pull it sharply. Allow the rope to return
to the handle slowly.
1. Control ba r
2. Throttle
1
Figure 7
3
3. Starter handle
6. When the engine starts, move the throttle control to
the Fast position, and set the ground speed control as
desired.
Note: If the engine fails to start after three pulls, repeat
steps 4 through 6.
222
Stopping the Engine
Release the control bar. Both the engine and the blade
should stop within 3 seconds. If they do not, contact an
Authorized Service Dealer.
Note: Close the fuel valve by moving the lever to the left
if you will not be starting the engine soon afterward.
9
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Using the Self-propel Drive
Self-propel Model only
The lawn mower has three ground speeds. 1 is slow, 2 is
medium, and 3 is fast. The ground speed control is located
at the rear of the belt cover (Fig. 9).
1
Figure 9
1. Ground speed control
1. Move the ground speed control to the (Neutral)
position.
2. Start the engine.
3. Squeeze the control bar against the handle to the
Run/Drive position (Fig. 10).
1
2
224
ground speed. Move the ground speed control to the
Neutral position when you use the lawn mower for
trimming or whenever you leave the lawn mower.
Using the Discharge Tunnel
Plug
1. Stop the engine and wait for all moving parts to stop.
2. Insert the discharge tunnel plug; refer to Installing the
Discharge Tunnel Plug on page 6.
3. To remove the plug, move the discharge door handle
rearward and lift up the spring clip on the bottom of
the plug. When the plug is unlocked, pull it out of the
discharge tunnel.
Note: When grass is thick and lush, clippings may collect
on and around the discharge tunnel plug. This may make
removing the plug difficult. Clean the plug thoroughly
after each use.
Adjusting the Cutting Height
Each wheel is adjusted individually with a wheel height
adjustment lever. Cutting heights are 3/4 inch (1.9 cm),
1-1/4 inches (3.2 cm), 1-3/4 inches (4.4 cm), 2-1/4 inches
(5.7 cm), 2-3/4 inches (7.0 cm), and 3-1/4 inches (8.3 cm).
Danger
3
m-3769
Figure 10
1. Run/Drive position
2. Run/Shift position
Note: Do not shift speeds while squeezing the control bar
against the handle in the Run/Drive position; this can
damage the transmission. Move the control bar to the
Run/Shift position (Fig. 10) when you change the ground
speed.
Note: You can vary the ground speed by increasing or
decreasing the distance between the control bar and the
handle. Lower the control bar to decrease the ground
speed when you are making a turn or if the lawn mower is
moving too fast for you. If you lower the control bar too
far, the lawn mower stops self-propelling. Squeeze the
control bar closer to the handle to increase the ground
speed. When you hold the control bar tight against the
handle, the lawn mower self-propels at the maximum
3. Stop position
Adjusting the cutting height levers could bring
your hands into contact with a moving blade and
result in serious injury.
• Stop the engine and wait for all moving parts to
stop before adjusting the cutting height.
• Do not put your fingers under the housing when
adjusting the cutting height.
1. Pull the wheel height adjustment lever toward the
wheel (Fig. 11) and move it to the desired setting.
1
m-225
Figure 11
1. Wheel height adjustment
lever
10
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
2. Release the wheel height adjustment lever and seat it
securely in the notch.
3. Adjust all the wheels to the same cutting height
setting.
1
Using the Grass Bag
Occasionally, you may want to use the grass bag for
bagging extra long grass, lush grass, or leaves.
Installing the Grass Bag
1. Stop the engine and wait for all moving parts to stop.
2. Ensure that the discharge door handle is fully forward
and that the pin is engaged in the catch (Fig. 12).
1
2
1. Pin locked in bag notch
Note: The discharge door in the lawn mower housing
is now open.
Mowing with the Grass Bag
m-1913
Figure 13
3
m-1912
Figure 12
1. Bag frame on retaining
post
2. Pin engaged in catch
3. Slide the hole in the bag frame onto the retaining post
on the discharge tunnel (Fig. 12).
4. Set the rear of the bag frame onto the bag support rod.
5. Pull the discharge door handle forward until the pin
clears the catch, and move the handle rearward until
the pin locks in the bag notch (Fig. 13).
3. Handle fully forward and
discharge door closed
Warning
A worn grass bag could allow small stones and
other similar debris to be thrown in the operator’s
or bystander’s direction and result in serious
personal injury or death to the operator or
bystanders.
Check the grass bag frequently. If it is damaged,
install a new Exmark replacement bag.
Cut the grass until the bag is full.
Important Do not overfill the bag.
Removing the Grass Bag
1. Stop the engine and wait for all moving parts to stop.
2. Raise the discharge door handle and move it forward
to engage the pin with the catch (Fig. 12).
3. Grasp the handles at the front and the rear of the bag
and lift the bag off the lawn mower.
4. Gradually tip the bag forward to empty the clippings.
5. To install the bag, refer to Installing the Grass Bag on
page 11.
11
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Danger
If the discharge door does not close completely,
the lawn mower could throw objects, causing
serious personal injury or death.
If you cannot close the door because the grass
clippings clog the discharge area, stop the engine
and gently move the discharge door handle back
and forth until you can close the door completely.
If you still cannot close the door, remove the
obstruction with a stick, not your hand.
Danger
The lawn mower can throw grass clippings and
other objects through an open discharge tunnel.
Objects thrown with enough force could cause
serious personal injury or death to the operator or
bystander.
Never open the door on the discharge tunnel when
the engine is running.
Operating Tips
• Review the safety instructions and read this manual
carefully before operating the lawn mower.
• Clear the area of sticks, stones, wire, branches, and
other debris that the blade could hit and throw.
• Keep everyone, especially children and pets, away
from the area of operation.
• Avoid striking trees, walls, curbs, or other solid
objects. Never deliberately mow over any object.
• If the lawn mower strikes an object or starts to vibrate,
immediately stop the engine, disconnect the wire from
the spark plug, and examine the lawn mower for
damage.
• Maintain a sharp blade throughout the cutting season.
Periodically file down nicks on the blade.
• Replace the blade when necessary with an original
Exmark replacement blade.
• Mow only dry grass or leaves. Wet grass and leaves
tend to clump on the yard and can cause the lawn
mower to plug or the engine to stall.
Warning
Wet grass or leaves can cause serious injury if you
slip and contact the blade.
Mow only in dry conditions.
• Clean the underside of the lawn mower housing after
each mowing. See Cleaning under the Housing on
page 15.
• Keep the engine in good running condition.
• Set the engine speed to the fastest position for the best
cutting results.
Warning
Operating a lawn mower with its engine running
at a speed greater than the factory setting can
cause the lawn mower to throw a part of the blade
or engine into the operator’s or bystander’s area
and result in serious personal injury or death.
• Do not change the engine speed setting.
• If you suspect the engine speed is faster than
normal, contact an Authorized Service Dealer.
• Clean the air filter frequently. Mulching stirs up more
clippings and dust which clogs the air filter and
reduces engine performance.
Cutting Grass
• Grass grows at different rates at different times of the
year. In the summer heat, it is best to cut grass at the
2-1/4-inch (5.7 cm), 2-3/4-inch (7.0 cm), or 3-1/4-inch
(8.3 cm) cutting height settings. Cut only about a third
of the grass blade at a time. Do not cut below the
2-1/4-inch (5.7 cm) setting unless the grass is sparse or
it is late fall when grass growth begins to slow down.
• When cutting grass over six inches (15 cm) tall, first
mow at the highest cutting height setting and walk
slower; then mow again at a lower setting for the best
lawn appearance. If the grass is too long and the leaves
clump on top of the lawn, the lawn mower may plug
and cause the engine to stall.
• Alternate the mowing direction. This helps disperse
the clippings over the lawn for even fertilization.
If the finished lawn appearance is unsatisfactory, try one
or more of the following:
• Sharpen the blade.
• Walk at a slower pace while mowing.
• Raise the cutting height on your lawn mower.
12
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
• Cut the grass more frequently.
• Overlap cutting swaths instead of cutting a full swath
with each pass.
• Set the cutting height on the front wheels one notch
lower than the rear wheels. For example, set the front
wheels at 2-1/4 inches (5.7 cm) and the rear wheels at
2-3/4 inches (7.0 cm).
Cutting Leaves
• After cutting the lawn, ensure that half of the lawn
shows through the cut leaf cover. You may need to
make more than one pass over the leaves.
• For light leaf coverage, set all the wheels at the same
cutting height setting.
• If there are more than five inches (12.7 cm) of leaves
on the lawn, set the front cutting height one or two
notches higher than the rear cutting height. This makes
it easier to feed the leaves under the lawn mower
housing.
• Slow down your mowing speed if the lawn mower
does not cut the leaves finely enough.
• If you mow over oak leaves, you can add lime to the
grass in the spring to reduce the acidity of the oak
leaves.
13
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Maintenance
Note: Determine the left and right sides of the machine from the normal operating position.
Recommended Maintenance Schedule
Maintenance Service
Interval
Each Use
5 Hours • Check the blade and the engine mounting fasteners. Tighten loose fasteners.
25 Hours
50 Hours
Maintenance Procedure
• Check the engine oil level. Refer to Checking the Engine Oil Level on page 15.
• Check the stopping time of the blade brake. The blade must stop within
3 seconds of releasing the control bar; if it does not, contact an Authorized
Service Dealer for repair.
• Remove grass clippings and dirt from under the housing. Refer to Cleaning
under the Housing on page 15.
• Clean the discharge tunnel and the discharge tunnel plug. Refer to Cleaning the
Discharge Tunnel and Plug on page 16.
• Inspect the air cleaner elements. Refer to Servicing the Air Cleaner on page 16.
• Clean the air cleaner elements; clean them more frequently in dusty operating
conditions. Refer to Servicing the Air Cleaner on page 16.
• Lubricate the pivot arms (self-propel model only). Refer to Lubricating the Pivot
Arms on page 19.
• Change the engine oil.1 Refer to Changing the Engine Oil on page 19.
• Sharpen or replace the blade; maintain it more frequently if the edge dulls
quickly in rough or in sandy conditions. Refer to Maintaining the Blade on
page 17.
• Remove grass clippings and debris from under the belt cover. Refer to Cleaning
under the Belt Cover on page 18.
• Have an authorized engine servicing dealer check and adjust the flywheel brake
pad.
75 Hours
100 Hours
250 Hours
1
Change the engine oil after the first 5 operating hours.
Important Refer to your engine owner’s manual for additional maintenance procedures.
• Adjust the self-propel drive system (self-propel model only). Refer to Adjusting
the Self-propel Drive on page 19.
• Inspect, clean, and adjust the spark plug; replace it if necessary. Refer to
Servicing the Spark Plug on page 20.
• Lubricate the gear case (self-propel model only). Refer to Lubricating the Gear
Case on page 20.
• Adjust the blade brake cable. Refer to Adjusting the Blade Brake Cable on
page 20.
• Service the wheels. Refer to Servicing the Wheels on page 21.
• Have an authorized engine servicing dealer check and adjust the idle speed,
check and adjust the valve clearance, and clean the fuel tank and filter.
• Replace the air cleaner elements; replace them more frequently in dusty
operating conditions. Refer to Servicing the Air Cleaner on page 16.
• Replace the spark plug. Refer to Servicing the Spark Plug on page 20.
• Have an authorized engine servicing dealer check for leaks in the fuel system
and/or a deteriorating fuel hose. Replace parts if necessary.
14
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Caution
If you leave the wire on the spark plug, someone could accidently start the engine and seriously
injure you or other bystanders.
Disconnect the wire from the spark plug before you do any maintenance. Set the wire aside so
that it does not accidently contact the spark plug.
Checking the Engine Oil Level
Before you use the lawn mower, ensure that the oil level is
between the lower limit and the upper limit marks as
shown on the dipstick (Fig. 5). If the oil level is below the
lower limit mark, add oil. Refer to Filling the Crankcase
with Oil on page 7.
Cleaning under the Housing
To ensure the best performance, keep the underside of the
housing clean (Fig. 14).
757
Figure 14
Washing Method
1. Position the lawn mower on a flat concrete or asphalt
surface near a garden hose.
2. Start the engine.
Note: The water will splash into the blade and clean
out the clippings. Let the water run until you no longer
see clippings being washed out from under the
housing.
4. Stop the engine and wait for all moving parts to stop.
5. Turn off the water.
6. Start the lawn mower again and let it run for a few
minutes to dry out the lawn mower and its
components.
Scraping Method
If the washing method does not remove all the debris from
under the lawn mower, scrape it clean.
1. Disconnect the wire from the spark plug (Fig. 6).
2. Drain the fuel from the fuel tank.
Warning
Tipping the lawn mower may cause the fuel to
leak from the carburetor or the fuel tank.
Gasoline is extremely flammable, highly explosive,
and, under certain conditions, can cause personal
injury or property damage.
Avoid fuel spills by running the engine dry or by
removing the gasoline with a hand pump; never
siphon.
3. Hold the running water at handle level and direct the
water to flow on the ground just in front of the right
rear tire (Fig. 15).
1
1093
Figure 15
1. Rear right tire
www.mymowerparts.com
3. Tip the lawn mower onto its left side (air cleaner up)
(Fig. 14).
4. Remove the dirt and grass clippings with a hardwood
scraper. Avoid burrs and sharp edges.
5. Return the lawn mower to the operating position.
6. Fill the fuel tank with fresh gasoline.
7. Connect the wire to the spark plug.
15
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Cleaning the Discharge Tunnel
and Plug
Remove the plug from the discharge tunnel and clean it
after each use.
Always ensure that the discharge tunnel door closes
securely when you release the handle. If the debris
prevents the discharge door from closing securely, clean
the inside of the discharge tunnel and the door thoroughly.
Warning
Grass clippings and other objects can be thrown
from an open discharge tunnel and cause serious
injury or kill the operator or bystanders.
Never start or operate the lawn mower unless one
of the following is true:
• The discharge tunnel plug is locked securely in
the discharge tunnel.
• The grass bag is locked in place.
• The optional side discharge chute is locked in
place.
• The discharge tunnel door is locked in place.
1
2
3
4
5
1. Wing bolts
2. Cover
3. Paper element
4. Remove the cover.
m-6674
Figure 16
4. Foam element
5. Base
Servicing the Air Cleaner
Inspect the air cleaner elements after every time you use
the lawn mower.
Clean the cover, base, and foam and paper elements after
every 25 operating hours. Replace the elements after
every 250 operating hours or sooner if they are damaged
or excessively dirty.
Important Do not operate the engine without the air
cleaner assembly; extreme engine damage will occur.
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Remove the 2 wing bolts that secure the cover
(Fig. 16).
Note: Be careful to prevent dirt and debris from falling
into the base.
5. Remove the foam and paper elements from the base
(Fig. 16).
6. Remove the foam element from the paper element
(Fig. 16).
7. Inspect the foam and paper elements, and replace them
if they are damaged or excessively dirty.
8. Tap the paper element on a hard surface several times
or use compressed air not exceeding 30 psi (207 kPa)
through the filter from the wire screen side to remove
any excess dirt. If the paper element is excessively
dirty, replace it.
Note: Never try to brush dirt off the paper element;
brushing forces the dirt into the fibers.
9. Clean the foam element in warm, soapy water or in a
nonflammable solvent.
Note: Do not use gasoline to clean the foam element
because it could create a risk of fire or explosion.
10.Rinse and dry the foam element thoroughly.
11. Dip the foam element in clean engine oil, then squeeze
out the excess oil.
Note: Excess oil in the foam element restricts the air
flow through the element and may reach the paper
filter and clog it.
16
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
12.Wipe dirt from the base and the cover with a moist
rag.
Note: Be careful to prevent dirt and debris from
entering the air duct leading to the carburetor.
13.Install the air cleaner elements and ensure that they are
properly positioned.
14. Securely install the cover with the 2 wing bolts.
Maintaining the Blade
Always mow with a sharp blade. A sharp blade cuts
cleanly and without tearing or shredding the grass blades.
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Drain the gasoline from the fuel tank.
4. Tip the lawn mower onto its right side (air cleaner up)
(Fig. 17).
2
1
1
A
2
B
3
C
4
Figure 18
1. Sail
2. Flat part of blade
Note: For the best performance, install a new blade before
the cutting season begins. During the year, file down any
small nicks to maintain the cutting edge.
3. Wear
4. Slot formed
1
1
270
Danger
A worn or damaged blade can break, and a piece
of the blade could be thrown into the operator’s
or bystander’s area, resulting in serious personal
injury or death.
757
1. Blade
2. Bolt and lock washer
3
Figure 17
3. Accelerator
Inspecting the Blade
Carefully examine the blade for sharpness and wear,
especially where the flat and the curved parts meet
(Fig. 18A). Because sand and abrasive material can wear
away the metal that connects the flat and curved parts of
the blade, check the blade before using the lawn mower. If
you notice a slot or wear (Figs. 18B and 18C), replace the
blade; refer to Removing the Blade on page 17.
• Inspect the blade periodically for wear or
damage.
• Replace a worn or damaged blade.
Removing the Blade
1. Grasp the end of the blade using a rag or a thickly
padded glove.
2. Remove the blade bolt, the lockwasher, the
accelerator, and the blade (Fig. 17).
17
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Sharpening the Blade
File the top side of the blade to maintain its original
cutting angle (Fig. 19A) and inner cutting edge radius
(Fig. 19B). The blade will remain balanced if you remove
the same amount of material from both cutting edges.
AB
1. Sharpen a t this angle only 2. Maintain the original
1
153
Figure 19
2
m4783
radius here
Balancing the Blade
1. Check the balance of the blade by placing the center
hole of the blade over a nail or screwdriver shank
clamped horizontally in a vise (Fig. 20).
Installing the Blade
1. Install a sharp, balanced Exmark blade, the
accelerator, the lock washer, and the blade bolt. The
sail of the blade must point toward the top of the lawn
mower housing for proper installation. Torque the
blade bolt to 50 ft-lb (68 Nm).
Warning
Operating the lawn mower without the
accelerator in place can cause the blade to flex,
bend, or break, resulting in serious injury or
death to the operator or bystanders.
Do not operate the lawn mower without the
accelerator.
2. Return the lawn mower to its upright position.
3. Connect the wire to the spark plug.
Cleaning under the Belt Cover
Self-propel Model only
1007
Figure 20
Note: You can also check the balance using a
commercially manufactured blade balancer.
2. If either end of the blade rotates downward, file that
end (not the cutting edge or the end near the cutting
edge). The blade is properly balanced when neither
end drops.
Keep the area under the belt cover free of debris.
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Remove the bolts that secure the belt cover to the lawn
mower housing (Fig. 21).
1
m-224
Figure 21
1. Belt cover
4. Lift off the cover and brush out all the debris around
the belt area.
5. Install the belt cover.
6. Connect the wire to the spark plug.
18
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Lubricating the Pivot Arms
Self-propel Model only
After every 25 operating hours or when the season ends,
lubricate the pivot arms.
1. Move the rear wheel cutting height levers to the center
setting.
2. Wipe the grease fittings with a clean rag (Fig. 22).
1
Figure 22
1. Grease fitting
3. Install a grease gun onto the fitting and gently apply
two or three pumps of #2 multi-purpose lithium base
grease (Fig. 22).
m-232
3. Slowly pull the lawn mower rearward while you
gradually move the control bar toward the handle.
Note: The adjustment is correct when the rear wheels stop
turning and the control bar is about one inch (2.5 cm)
from the handle (Fig. 24).
1
m-513a
Figure 24
1. One inch (2.5 cm)
Changing the Engine Oil
Change the oil after the first 5 operating hours (or the first
month); and then after every 50 operating hours (or every
6 months).
1. Run the engine to warm the engine oil.
Note: Warm oil flows better and carries more
contaminants.
Note: Applying grease with excessive pressure may
damage the seals.
Adjusting the Self-propel Drive
Self-propel Model only
If the lawn mower does not self-propel or has a tendency
to creep forward when the control bar is more than 1-1/2
inches (3.8 cm) from the handle, adjust the wheel drive
control knob on the rear of the gear box (Fig. 23).
1
m-228
Figure 23
1. Control knob
Warning
Oil may be hot after engine has been run, and
contact with hot oil can cause severe personal
injury.
Avoid contacting the hot engine oil when you
drain it.
2. Stop the engine and wait for all moving parts to stop.
3. Disconnect the wire from the spark plug (Fig. 6).
4. Place a suitable drain pan under the dipstick/oil drain
(Fig. 6).
5. Clean around the dipstick.
6. Remove the dipstick by rotating the cap
counterclockwise and pulling it out.
7. Raise the left side of the lawn mower to drain the oil
from the dipstick fill tube into the drain pan.
8. After draining the oil, return the lawn mower to the
operating position.
1. Close the door in the lawn mower housing and remove
the grass bag.
2. Rotate the control knob clockwise / turn if the lawn
mower does not self-propel. If the lawn mower creeps
forward, rotate the knob / turn counterclockwise
(Fig. 23).
www.mymowerparts.com
9. Fill the crankcase with fresh oil to the upper limit
mark on the dipstick. Refer to the Filling the
Crankcase with Oil on page 7.
10.Insert the dipstick into the filler neck and rotate the
cap clockwise until it is tight.
19
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
11. Wipe up any spilled oil.
12.Connect the wire to the spark plug.
13.Recycle the used oil according to local codes.
Servicing the Spark Plug
Check the spark plug after every 100 operating hours or
yearly; replace it after every 250 operating hours or every
2 years. Use an NGK BPR5ES or Nippondenso
W16EPR-U spark plug or equivalent.
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Clean around the spark plug.
4. Remove the spark plug from the cylinder head.
Important Replace a cracked, fouled, or dirty spark
plug. Do not clean the electrodes because grit entering the
cylinder can damage the engine.
5. Set the gap on the plug to 0.030 in. (0.76 mm)
(Fig. 25).
Lubricating the Gear Case
Self-propel Model only
After every 100 operating hours, grease the gear case.
1. Remove the grass bag.
2. Install a grease gun onto the fitting through the belt
cover opening (Fig. 26).
2
1
m-224
Figure 26
1. Belt cover 2. Grease fitting
3. Gently apply one to two pumps of #2 multi-purpose
lithium-base grease.
1
m-110
Figure 25
1. 0.030 in. (0.76 mm)
6. Carefully install the spark plug by hand (to avoid cross
threading) until it is hand tight.
7. Tighten the spark plug an additional 1/2 turn if it is
new; otherwise, tighten it an additional 1/8 to 1/4 turn.
Important A loose spark plug can become very hot
and can damage the engine; overtightening a spark plug
may damage the threads in the cylinder head.
8. Connect the wire to the spark plug.
4. Install the grass bag.
Adjusting the Blade Brake
Cable
Whenever you install a new blade brake cable assembly,
adjust it.
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Check the adjustment of the cable by moving the
control bar toward the handle until you remove the
slack in the cable. The gap between the brake lever
and the handle must be between 3/16 and 1/4 in.
(5 and 6 mm). To adjust the cable, go to step 4.
20
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
4. To adjust the cable, do the following:
Hand-push Model
A. Loosen the jam nut on the blade brake cable
(Fig. 27).
1
2
3
4
5
6
483
Figure 27
1. Handle
2. Brake lever
3. 3/16 to 1/4 in. (5 to 6 mm)
4. Cable adjuster
5. Jam nut
6. cable conduit
B. Insert a 3/16 to 1/4 in. (5 to 6 mm) object between
the brake lever and the handle.
C. Turn the cable adjuster on the brake cable until you
remove the slack.
D. Tighten the jam nut.
Servicing the Wheels
Removing the Wheels
1. Stop the engine and wait for all moving parts to stop.
2. Disconnect the wire from the spark plug (Fig. 6).
3. Remove the bolt, the wheel spacer, and the locknut
mounting the wheel to the pivot arm (Fig. 29).
12 3 45
67 5 7 8 9
Figure 29
1. Locknut
2. Wheel spacer
3. Bearing/hub assembly
4. Bearing spacer
5. Wheel half
6. Plastic cover (rear wheels
only)
7. Lug
8. Bearing (2)
9. Bolt
1
296
Self-propel Model
A. Loosen the nut on the cable bracket (Fig. 28).
1
2
3
4
Figure 28
1. Handle
2. Brake lever
3. 3/16 to 1/4 in. (5 to 6 mm)
4. cable bracket
B. Insert a 3/16 to 1/4 in. (5 to 6 mm) object between
the brake lever and the handle.
C. Pull down on the cable conduit until you remove
the slack from the wire.
D. Tighten the nut.
4. Separate the wheel halves from the tire by removing
four bolts and four locknuts (Fig. 29).
Note: If you remove the bearings from the bearing/hub
assembly, remove them by pressing on the bearing spacer
(Fig. 29).
Assembling the Wheels
1. Position the tire onto one wheel half, aligning the lugs
on each (Fig. 29).
2. Place the bearing/hub assembly into the center hole of
the wheel half. Ensure that the legs of the hub are
positioned over the flange of the hole (Fig. 29).
3. Place the other wheel half onto the bearing/hub
assembly, aligning the wheel and the tire lugs and the
mounting holes (Fig. 29).
4. Using two 1/4–20 x 1.50 in. (6 x 38 mm) fully
threaded bolts and non-locking nuts, loosely secure the
wheel halves together. Mount the bolts in the opposing
holes (Fig. 29).
5. Check the alignment of all parts and tighten the bolts,
alternating from side to side for a uniform fit, until the
wheel halves are drawn together (Fig. 29).
21
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
6. Install the two bolts and two locknuts previously
removed in the remaining holes in the wheel halves
and tighten. Remove the two long bolts and replace
them with two bolts and two locknuts (Fig. 29).
7. Install the wheel to the pivot arm with the bolts, a
spacer, and a locknut. Ensure that the spacer is
positioned between the wheel hub and the pivot arm
(Fig. 29).
Storage
To prepare the lawn mower for off-season storage,
perform the recommended maintenance procedures. Refer
to Maintenance on page 14.
Store the lawn mower in a cool, clean, and dry place.
Cover the lawn mower to keep it clean and protected.
Preparing the Fuel System
Warning
Gasoline can vaporize if you store it over long
periods of time and explode if it comes into
contact with an open flame.
• Do not store gasoline over long periods of time.
• Do not store the lawn mower with gasoline in
the fuel tank or the carburetor in an enclosure
with an open flame. (For example, a furnace or
a water heater pilot light.)
• Allow the engine to cool before storing it in any
enclosure.
Empty the fuel tank when mowing the last time before
storing the lawn mower.
1. Run the lawn mower until the engine stops from
running out of fuel.
2. Prime the engine and start it again.
3. Allow the engine to run until it stops. When you can
no longer start the engine, it is sufficiently dry.
5. Install the spark plug but do not connect the wire to
the spark plug.
General Information
1. Clean the lawn mower housing. Refer to Cleaning
under the Housing on page 15.
2. Clean any dirt and chaff from the cylinder, cylinder
head fins, and blower housing.
3. Remove grass clippings, dirt, and grime from the
external parts of the engine, the shrouding, and the top
of the lawn mower housing.
4. Check the condition of the blade. Refer to Maintaining
the Blade on page 17.
5. Service the air cleaner; refer to Servicing the Air
Cleaner on page 16.
6. Lubricate the pivot arms (self-propel model only);
refer to Lubricating the Pivot Arms on page 19.
7. Tighten all nuts, bolts, and screws.
8. Touch up all rusted or chipped paint surfaces with
paint available from an Authorized Service Dealer.
Removing the Lawn Mower
from Storage
1. Check and tighten all fasteners.
2. Remove the spark plug and spin the engine rapidly
using the starter to blow the excess oil from the
cylinder.
3. Clean the spark plug or replace it if it is cracked,
broken, or if the electrodes are worn.
4. Install the spark plug. Refer to Servicing the Spark
Plug on page 20.
5. Perform any needed maintenance procedures; refer to
Maintenance on page 14.
6. Fill the fuel in the fuel tank with fresh gasoline.
7. Check the engine oil level.
Preparing the Engine
1. While the engine is still warm, change the oil from the
crankcase. Refer to Changing the Engine Oil on
page 19.
2. Remove the spark plug (Fig. 6).
3. Using an oil can, add about one tablespoon of oil to
the crankcase through the spark plug hole.
4. Slowly rotate the engine several times, using the
starter rope, to distribute the oil.
www.mymowerparts.com
8. Connect the wire to the spark plug.
Accessories
You may purchase the following accessory from an
Authorized Service Dealer:
Side Discharge Kit
22
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Troubleshooting
Exmark designed and built your lawn mower for trouble-free operation. Check the following components and items
carefully, and refer to Maintenance on page 14 for more information. If a problem continues, contact an Authorized
Service Dealer.
Problem Possible Causes Corrective Action
Engine does not start 1. The fuel tank is empty or the
fuel system contains stale fuel.
2. The throttle lever is not in the
Choke position.
3. The wire is not connected to
the spark plug.
4. The spark plug is pitted, fouled,
or the gap is incorrect.
Engine starts hard or loses power 1. The fuel tank contains stale
fuel.
2. The fuel cap vent hole is
plugged.
3. The air cleaner elements are
dirty and are restricting the air
flow.
4. The underside of the lawn
mower housing contains
clippings and debris.
5. The spark plug is pitted, fouled,
or the gap is incorrect.
6. The engine oil level is low or
the oil is dirty.
1. Drain and/or fill the fuel tank
with fresh gasoline. If the
problem persists, contact an
Authorized Service Dealer.
2. Move the throttle lever to the
Choke position.
3. Connect the wire to the spark
plug.
4. Check the spark plug and
adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.
1. Drain and fill the fuel tank with
fresh gasoline.
2. Clean the fuel cap vent hole or
replace the fuel cap.
3. Service the air cleaner
elements.
4. Clean under the lawn mower
housing.
5. Check the spark plug and
adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.
6. Check the engine oil. Change
the oil if it is dirty or add oil if it
is low.
Engine runs rough 1. The wire is not connected to
the spark plug.
2. The spark plug is pitted, fouled,
or the gap is incorrect.
3. The throttle lever is not in the
Fast position.
4. The air cleaner elements are
dirty and are restricting the air
flow.
23
www.mymowerparts.com
1. Connect the wire to the spark
plug.
2. Check the spark plug and
adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.
3. Move the throttle lever to the
Fast position.
4. Service the air cleaner
elements.
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Problem Corrective ActionPossible Causes
Lawn mower or engine vibrates
excessively
Uneven cutting pattern 1. All four wheels are not at the
Discharge chute plugs 1. The throttle lever is not in the
1. The blade is bent or is out of
balance.
2. The blade mounting nuts are
loose.
3. The underside of the lawn
mower housing contains
clippings and debris.
4. The engine mounting bolts are
loose.
same height.
2. The blade is dull.
3. You are mowing in the same
pattern repeatedly.
4. The underside of the lawn
mower housing contains
clippings and debris.
Fast position.
2. The cutting height is too low.
3. You are mowing too fast.
4. The grass is wet.
5. The underside of the lawn
mower housing contains
clippings and debris.
1. Balance the blade. If the blade
is bent, replace it.
2. Tighten the blade mounting
nuts.
3. Clean under the lawn mower
housing.
4. Tighten the engine mounting
bolts.
1. Place all four wheels at the
same height.
2. Sharpen and balance the
blade.
3. Change the mowing pattern.
4. Clean under the lawn mower
housing.
1. Move the throttle lever to the
Fast position.
2. Raise the cutting height.
3. Slow down.
4. Allow the grass to dry before
mowing.
5. Clean under the lawn mower
housing.
Lawn mower does not self-propel
(Self-propel model only)
1. The self-propel drive cable is
out of adjustment or is
damaged.
2. There is debris under the belt
cover.
1. Adjust the self-propel drive
cable. Replace the cable if
necessary.
2. Clean the debris from under
the belt cover.
24
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
25
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
Limited Warranty
Exmark Commercial Turf Equipment
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty Company,
pursuant to an agreement between them, jointly warrant on the
terms and conditions herein, that we will repair, replace or adjust
any part manufactured by Exmark and found by us (in the exercise
of our reasonable discretion) to be defective in factory material or
workmanship.
This warranty is limited to one year from the date of original retail
purchase (90 days for rental use) for any Exmark mower that is
used for commercial or any other income producing purpose. The
blade spindle assemblies will be warranted for three years, one
year parts and labor with an additional two years parts only , from
date of original retail purchase against defects in materials or
workmanship. The hydrostatic traction drive system, excluding
hoses, will be warranted for two full years from date of original retail
purchase against defects in materials or workmanship. We will
extend the Peerless 5-speed transmission manufacturer’s warranty from 90 days to one year. Belts and tires are warranted for 90
days against defects in materials or workmanship.
The engine warranty is covered by its respective engine manufacturer. Please refer to the engine manufacturer’s warranty statement that is included in the literature packet. We are not authorized
to handle warranty adjustments on engines. Engine warranties
should be referred to the nearest authorized service outlet of the
engine manufacturer.
This warranty extends only to the original retail purchaser of the
equipment. This warranty may not be assigned or transferred
without the prior express written consent of Exmark and Exmark
Warranty Company. The warranty period commences upon the
date of original retail purchase.
The Exmark turf equipment, including any defective part, must be
returned to an authorized Exmark service dealer within the
warranty period. The warranty shall extend to the expense of repair
or replacement (as determined by us) of the defective part,
including labor. The warranty shall not extend to the expense of
delivering the mower to the dealer for warranty work nor the
expense of returning it back to the owner after repair or
replacement. Our responsibility in respect to claims is limited to
making the required repairs or replacements, and no claim of
breach of warranty shall be cause for cancellation or rescission of
the contract of sale of any Exmark mower. Proof of purchase may
be required by the dealer to substantiate any warranty claim. All
warranty work must be performed by an authorized Exmark
service dealer.
This warranty extends only to turf equipment operated under
normal conditions and properly serviced and maintained. The
warranty expressly does not cover (1) any damage or deterioration
due to normal use, wear and tear, or exposure; (2) normal
maintenance services, such as oil change, cleaning, lubrication, or
adjustment; (3) replacement of service items, such as oil,
lubricants, spark plugs, or other items subject to normal service
replacement; (4) damage or defects arising out of or relating to
misuse, neglect, alteration, negligence, or accident; (5) repair or
replacement arising from operation of or use of the turf equipment
which is not in accordance with operating instructions as specified
in the operator’s manual or other operational instructions provided
by Exmark; (6) repair or replacement arising as a result of any
operation from turf equipment that has been altered or modified so
as to, in the determination of Exmark or Exmark Warranty
Company, adversely affect the operation, performance or durability of the equipment or that has altered, modified or affected the turf
equipment so as to change the intended use of the product; (7)
repair or replacement necessitated by use of parts, accessories or
supplies, including gasoline, oil, or lubricants, incompatible with
the turf equipment or other than as recommended in the operator’s
manual or other operational instructions provided by Exmark; (8)
repairs or replacements resulting from parts or accessories which
have adversely affected the operation, performance, or durability
of the turf equipment; or (9) damage or defects due to or arising out
of repair of turf equipment by person or persons other than an
authorized Exmark service dealer or the installation of parts other
than genuine Exmark or Exmark recommended parts.
As a condition to this warranty, the customer shall have read the
operator’s manual and shall have completed and returned to
Exmark Warranty Company, within the prescribed time, the
Exmark warranty registration.
The sole liability of Exmark and Exmark Warranty Company, with
respect to this warranty, shall be repair and replacement as set
forth herein. Neither Exmark nor Exmark Warranty Company shall
have liability for any other cost, loss, or damage, including but not
limited to, any incidental or consequential loss or damage. In
particular, we shall have no liability or responsibility for (1)
expenses relating to gasoline, oil, or lubricants; (2) loss, cost, or
expense relating to transportation or delivery of turf equipment
from the location of owner or location where used by owner to or
from any authorized Exmark service dealer; (3) travel time,
overtime, after hours time, or other extraordinary repair charges or
charge relating to repairs or replacements outside of normal
business hours at the place of business of the authorized Exmark
service dealer; (4) rental of like or similar replacement equipment
during the period of any warranty , repair, or replacement work; (5)
any telephone or telegram charges or travel charges; (6) loss or
damage to person or property other than that covered by the terms
of this warranty; (7) any claims for lost revenue, lost profit, or
additional cost as a result of a claim of breach of warranty; or (8)
attorney’s fees.
There are no representations or warranties which have been
authorized and provided to the buyer of the turf equipment other
than as set forth in this warranty. Any and all statements or
representations made by any seller of this equipment, including
those set forth in any sales literature or made orally by any sales
representative, are superseded by the terms of this warranty. Any
affirmation of fact or promise made by Exmark, Exmark Warranty
Company, or any of their representatives, to the buyer, which
relates to the goods that are the subject of this warranty, shall be
regarded as part of the basis of the bargain and shall not be
deemed to create any express warranty that such goods shall
conform to the affirmation or promise.
THERE ARE NO OTHER UNDERSTANDINGS, AGREEMENTS,
REPRESENTATIONS, OR WARRANTIES, EXPRESS OR IMPLIED (INCLUDING BUT NOT LIMITED TO ANY REGARDING
THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE), NOT SPECIFIED HEREIN, RESPECTING THE
EQUIPMENT WHICH IS THE SUBJECT OF THIS WARRANTY.
This warranty applies to all Exmark turf equipment sold in the
United States and Canada and intended to be used for commercial
purposes.
Rev. 11/12/1999
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
SERVICE RECORD
Date Description Work Done Service Done By
www.mymowerparts.com
For Exmark Mower Parts Call 606-678-9623 or 606-561-4983
SEE EXMARK’S COMPLETE
LINE OF PRODUCTS FOR TURF CARE
LAZER Z
LAZER Z
HP
LAZER Z XP LAZER Z CT
TURF RANGER
TURF TRACER
METRO
HP VIKING HYDRO
TURF TRACER
METRO HP
ULTRA VAC ULTRA VAC QDS
GRASS CATCHER SELF STEERING SULKY
MICRO-MULCH ACCESSORY
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects, or other reproductive
harm.
2003
EXMARK MFG. CO. INC.
INDUSTRIAL PARK BOX 808
BEATRICE, NE 68310
ALL RIGHTS RESERVED
Warning
CALIFORNIA
Proposition 65 Warning
FORM NO. 3327-672
(402) 223-6300
FAX (402) 223-5489
PRINTED IN U. S. A.
www.mymowerparts.com
Loading...