Exland EL-17PA1L, EL-19PA1L User Manual

CCTV LCD Monitor

User Manual

For models:

EL-17PA1L

EL-19PA1L

_____________________

1. Introduction………...........................................................................................................................................1

2. Work Safety Information................................................................................................................................ 2

2.1. Product Safety Precautions information.......................................................................................................2

2.2. Safety Guidelines.........................................................................................................................................3

2.3. Important Notice Concerning Power Cord Selection...................................................................................3

2.3.1 For the United States and Canada..................................................................................................... 3

2.3.2 For European Countries......................................................................................................................3

2.3.3 For the United Kingdom.......................................................................................................................4

3. Standards and Guidelines.............................................................................................................................5

3.1. FCC Requirements......................................................................................................................................5

3.2. FCC Warning ............................................................................................................................................ 5

3.3 CE Conformity……………........................................................................................................................... 5

3.4 RoHS Compliance Statement.................................................................................................................... 5

3.5 Information on Disposal for Your Old Product..............................................................................................6

4. Hardware Installation.....................................................................................................................................7

4.1 Checking the Accessories Supplied..............................................................................................................7

5. Buttons and Connections...............................................................................................................................7

5.1 Buttons……..................................................................................................................................................7

5.2 Connections..................................................................................................................................................8

6. ID Remote Controller ………………………………………………………………………………… ………..…….9

7. OSD Setup ……………………………………………………………………………………… ………………..……10

8. Troubleshooting Guide…………………………………………………………………………………………….…19

9. Applicable Video Timing for PC- analog Video…………………………………………………………….….…20

10.Technical Data ………………………………………………………………………………… ……………… …… ..21

Contents

1 Introduction

Thank you for purchasing the professional CCTV LCD Monitor and welcome to a fantastic new technology that will completely change the way you look at monitors. The following sections describe just a few of the major advantages of this LCD monitor. You’ll discover more of its wonderful features as you use it.

Please note that this manual is used with many similar monitor models. Please check the model number on the carton and on the back of the unit to make sure if the user manual is applicable to your machine.

1. The LCD monitor is used in the same way as the CRT monitor. There is no need to change the hardware of your computer, just plug it in and it is ready for use.

2. The monitor will accept and display analog video (NTSC or PAL) , PC-type video and Digital video sources .

3. Low radiation and reduced flickering compared to traditional CRT monitors that minimizes eyestrain and health hazards.

4. The compact size makes transportation easier and allows to use in many applications.

5. This LCD monitor can support PC-VGA, Composite , S-Video signals.

6. The composite video input ports accept different signal sources, e.g. Camera, DVR .. etc.

7. The design allows VESA wall mounting installation.

8 This monitor includes special functions for 3D comb filter, De-interlace, Anti burn-in mode, auto

impedance switch for looping video connection .

9. The remote controller has 9999 ID code to control individual monitor on the wall. (Remote controller is an optional device)

2 Work Safety Information

Caution and Warning

CAUTION !!

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No internal parts can be serviced by users. Refer servicing to qualified personnel.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS CCTV LCD MONITOR TO RAIN OR MOISTURE.

“HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS CCTV LCD MONITOR. BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE BY CONNECTING THE H.V. METER BETWEEN THE BACK LIGHT POWER LEAD AND CHASSIS ONLY“

2.1 Product Safety Precautions

Follow all warnings and instructions marked on the product.

1. Do not use this product near water.

2. This LCD monitor should be installed on a stable horizontal base.

3. When cleaning, use only a neutral detergent cleaner with a soft damp cloth. Do not spray with liquid or

aerosol cleaners.

4. Do not expose this LCD monitor to direct sunlight or heat. Hot air may cause damage to the cabinet and other parts.

5. Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the LCD monitor from overheating. Do not block ventilation slots and openings with objects or install the LCD monitor in a place where ventilation may be obstructed.

6. Do not install this LCD monitor near a motor or transformer where strong magnetism is generated. Images on the LCD monitor will be distorted and the color irregular.

7. Do not allow metal pieces or objects of any kind fall into the LCD monitor through ventilation holes.

8. Do not attempt to service this unit yourself. Removal of the LCD monitor cover may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

9. Unplug this product from the wall outlet and refer servicing to qualified service personnel in the event that:

- Liquid is spilled onto the product or the product is exposed to rain or water.

- The product does not operate normally when the operating instructions are followed.

- The product has been dropped or the cabinet has been damaged.

- The product exhibits a distinct change in performance, indicating a need for service.

- The power cord or plug is frayed or damaged.

- Has referred to Troubleshooting Tips and problems still can’t be solved. 2

2.2 Safety Guidelines

WARNING This device must be operated with the original power supply.

CAUTION

The socket outlet should be installed near the equipment and should be easily accessible.

CAUTION

Use a power cord that is properly grounded. Always use the appropriate AC power cord that is certified for the individual country. Some examples are listed below:

USA………..UL Switzerland…….SEV Canada……CSA Britain…………..BASE/BS Germany…..DE Japan…………...Electric Appliance Control Act.

2.3 Important Notice Concerning Power Cord Selection

The power cord set for this unit has been enclosed and has been selected acco rding to the country of destination. It must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original cord set, or if the cord set is not enclosed.

The female receptacle of the cord set must meet IEC-60320 requirements and may look like this (Figure A1 below):

Figure A1 Figure A2

2.3.1 For the United States and Canada

In the United States and Canada the male plug is a NEMA5-15 style (Figure A2, above), UL Listed, and CSA Labeled. For units which are mounted on a desk or table, SVT or SJT type cord sets may be used. For units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your unit. Please consult the table below for the selection criteria for power cords used in the United States and Canada.

Code Type Size of Conductors in Cord Maximum Current Rating of Unit

SJT 18 AWG

16 AWG 14 AWG

10 Amps 12 Amps 12 Amps

SVT 18 AWG

17 AWG

10 Amps 12 Amps

2.3.2 For European Countries

In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HAR-Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors.

English Fran

çais

tsch E

spaño

Italiano Polski

Česk

enska

Nederlan

2.3.3 For the United Kingdom

For your safety please read the following text carefully. If the fitted molded plug is unsuitable for the socket outlet, then the plug should be cut off and disposed of

safely.

DANGER

Do not plug the cut-off plug into a socket outlet! There is a danger of severe electrical shock!

If a new plug is to be fitted, please observe the wiring code as shown below. In case of doubt, please consult a qualified electrician.

WARNING This appliance must be earthed (grounded).

IMPORTANT

The wires in this mains lead are colored in accordance with the following codes:

z Green-and- Yellow : Ground (Earth) z Blue : Neutral z Brown : Live

If the colored wires of the mains lead of this appliance do not correspond with the colored markings identifying the terminals in your plug, proceed as follows:

The wire which is colored GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or colored GREEN or GREEN-AND-YELLOW.

The wire which is colored BLUE must be connected to the terminal in the plug which is marked with the letter N or colored BLACK.

The wire which is colored BROWN must be connected to the terminal in the plug which is marked with the letter L or colored RED.

If you have any questions concerning the proper power cord to use, please consult the dealer from whom you purchased the product.

3 Standards and Guidelines

3.1 FCC Requirements

This device complies with Part 15 of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must tolerate any interference encountered, including interference that may cause improper operation.

The equipment has been tested and found to comply with the requirements stipulated in Part 15 of FCC regulations for a Class B digital device. These requirements are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict compliance with the instructions, may disrupt radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause detrimental interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by taking one or more of the following measures:

z Reorienting or relocating the receiving antenna. z Increasing the separation between the equipment and the receiver. z Connecting the equipment into an outlet on a circuit different from the one which the receiver is connected. z Consulting the dealer or an experienced radio/TV technician for help.

Shielded interconnected cables and shielded power cords must be used with this equipment to ensure compliance with the pertinent RFD emission limits governing this device.

Changes or modifications not expressly approved by the manufacturer could void the user’s right to operate the equipment.

Notice of Compliance with Canadian Interference-causing Equipment Regulations

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

3.2 FCC Warning

To ensure continued FCC compliance, the user must use a grounded power supply cord and the shielded video interface cord with bonded ferrite cores provided. If a BNC cable is going to be used, use only a shielded BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

3.3 CE Conformity

The device complies with the requirements of the directive 2004/108/EC with regard to “Electromagnetic compatibility”, and 206/95/EC with regard to “Safety”.

English

Français