1
Connect Devices
3
Apply Power
4
Confi gure Network
2
Connect to Network
A
LED DescripƟ ons
PROCEED TO STEP 2
PROCEED TO STEP 3
Insert the SIM card and
mount the antenna
WAN (enabled by default)
2G/3G (EC350 only)
Make sure that the SIM card has
a mobile data plan and allows
text messaging, and that PIN code
security has been disabled.
Apply power
StaƟ c IP or 2G/3G: PROCEED TO STEP 4
DHCP: PROCEED TO SECTION B ON REVERSE
LED Name Color IndicaƟ on Possible acƟ ons
Modem (EC350 only)
OFF Modem disabled
Steady red Modem failure See the User Manual for more informaƟ on.
Flashing red SIM card failure Check that the SIM card is correctly inserted and not damaged.
Steady orange PIN code enabled on SIM card Disable PIN code on the SIM card.
Flashing orange No APN server specifi ed Set the APN (Access Point Name) from the onboard webpage.
Steady green Modem registered on mobile network
Flashing green Modem is searching for mobile network.
RS485/RS232
OFF Port disabled
Steady red Port failure/communicaƟ ons issue See the User Manual for more informaƟ on.
Steady green CommunicaƟ ons OK
Uplink/WAN
Steady green Connected to Internet
Steady red Incorrect IP seƫ ngs
DHCP: Check for DHCP server on network.
StaƟ c IP: Check seƫ ngs for IP address, gateway and DNS.
Flashing red Unable to connect to Internet Check network seƫ ngs and fi rewalls.
Gateway
OFF Unit has no power, or is starƟ ng up
Steady green Normal operaƟ on
Flashing green Firmware update in progress.
Steady red Hardware failure See the User Manual for more informaƟ on.
Flashing red ApplicaƟ on failure See the User Manual for more informaƟ on.
Power
OFF No power
Steady green Unit has power
Ethernet Link
(located on RJ-45 ports)
OFF No network detected
Orange fl icker AcƟ vity on 10 Mbps Ethernet network
Green fl icker AcƟ vity on 100 Mbps Ethernet network
See reverse for informaƟ on about the connecƟ ons
Insert SIM card
Connect network
to WAN port
Connect Serial
Devices
Make sure that there is a
good connecƟ on to the
mobile network.
See LED DescripƟ ons.
Connect 12–48 VDC to pin +
Connect Power Ground to pin -
Ethernet with
StaƟ c IP address
2G/3G
(EC350 only)
PROCEED TO SECTION B ON REVERSE
Confi gure IP seƫ ngs.
See secƟ on C on reverse.
To check the mobile signal strength on EC350:
Press and release the Mode buƩ on. The top 5 LEDs
will now show signal strength for 60 seconds:
• 1 Flashing Red LED: No/unknown signal
• 1 Flashing Orange LED: Poor signal
• 1 Flashing Green LED: OK signal
• 2-5 Flashing Green LEDs: Good to opƟ mum signal
RS-485 RS-232
Connect Ethernet
Devices to LAN port
LAN
Before you install the Netbiter, make sure that you have all the necessary
informaƟ on about your local network environment. Contact your network
administrator if in doubt.
Select
Network
Type
Network
Type
B
D
C
E
AcƟ vate the Netbiter
ConnecƟ ons
Local Confi guraƟ on Technical Data
EC310/EC350
INSTALLATION GUIDE
Local Confi guraƟ on via USB
Connect a USB Micro B cable between a computer and the USB port on the
Netbiter. The USB device driver will create a virtual network interface on the
computer, with an IP address in the range 169.254.200.xxx.
Accessing the local confi guraƟ on
Enter the IP address 169.254.200.200 in a web browser.
The default username for the local confi guraƟ on pages is admin.
The password is the AcƟ vaƟ on Code supplied with the unit.
The Netbiter must be acƟ vated to be able to communicate with Netbiter Argos.
This requires the System ID and AcƟ vaƟ on Code, both of which are provided on a
printed sheet included with the Netbiter.
To open a new account on Netbiter Argos:
1. Go to
www.netbiter.net and click on Create an account.
2. Follow the instrucƟ ons and log in to the new account.
3. Select the primary use for the unit and click on AcƟ vate.
To use an exisƟ ng Netbiter Argos account:
1. Go to www.netbiter.net and log in to your Argos account.
2. Open the menu Management >> All Systems >> Add system.
Refer to the online help in Argos if needed (see below).
Requirements for Mobile CommunicaƟ on
If the SIM card is not a Netbiter SIM card the following informaƟ on is needed:
• The phone number for the SIM card
• The access point name (APN)
• The username and password (if required by the operator)
The informaƟ on can be entered in two ways:
• In the local confi guraƟ on pages under
Modem seƫ ngs (see secƟ on C)
• In Netbiter Argos on the
Mobile network confi guraƟ on page
The PIN code for the SIM card must be disabled.
Online Help
The help system in Netbiter Argos can be accessed by clicking on the icon in the
top right corner of the web page.
HMS Industrial Networks AB
Box 4126
300 04 Halmstad
Sweden
Phone +46 (0)35 - 17 29 00
Fax +46 (0)35 - 17 29 09
E-mail info@hms.se
Web www.hms-networks.com
Support www.netbiter.com/support
©2016 HMS Industrial Networks - All rights reserved
HMS reserves the right to make modifi caƟ ons without prior noƟ ce.
For a Netbiter SIM card the APN seƫ ngs are pre-confi gured on
Netbiter Argos and the PIN code is disabled upon delivery.
Package Contents DescripƟ on
Netbiter EC310 or EC350
Connectors Connectors for I/O, RS-232 and RS-485 teminals
System ID/AcƟ vaƟ on code Printed document with installaƟ on credenƟ als
InstallaƟ on Guide This document
Stub antenna NB1005 only
DIN Rail MounƟ ng Kit NB1005 and NB1007 only
Once the Netbiter is online at Netbiter Argos, check
that the unit is running the latest fi rmware.
SP1829 3.10 2016-10-03
Field wiring terminals must be connected with minimum wire size 24 AWG
Power Connector
SIM Card Slot (EC350 only)
I/O Terminal Block
RS-232 RS-485
GPS antenna connector
(EC350 only)
WAN
Pin DescripƟ on
Rx Rx Recieve Input RS-232
Tx Tx Transmit Output RS-232
GND Signal ground
Pin DescripƟ on
A RS-485 Line A (+)
B RS-485 Line B (-)
COM ISO GND (Isolated ground)
Micro USB
Connector
ProtecƟ ve Earth
(for Ethernet ports)
Pin Label DescripƟ on
1 Relay NO Relay Output, NO, Isolated
2 Relay COM Relay Output, COM, Isolated
3 DI1+ Digital input 1 current source
4 DI1- Digital input 1
5 DI2+ Digital input 2 current source
6 DI2- Digital input 2
7 Analog In AI1 Analog Input 1
8 Analog In AI2 Analog Input 2
9 Analog In AI3 Analog Input 3
10 Analog In AI4 Analog Input 4
11 Analog IN COM Analog Ground
I/O Terminal Block
Ea
(
LAN
2G/3G antenna connector
(EC350 only)
• Do not connect power to the digital inputs!
• Relay max 24 V AC/DC, 1 A
Mode BuƩ on
PowerCononnector
SIM
Cardr
Slot (EC350 only)
I/
O Terminal Block
US
B
tor
Ethernet link indicators
iink
ind
s
Order Code
EC310: NB1007
EC350: NB1005
EC350 (no antenna): NB1008
Mobile communicaƟ on (EC350 only)
5-band 3G/UMTS (WCDMA/FDD):
800/850, 900, 1900, 2100 MHz
Quad-band GSM/GPRS:
850, 900, 1800, 1900 MHz
1 Relay Output
2 Digital Inputs (dry contact type)
4 Analog Inputs
V, mA (all 4 inputs)
Pt100 (2 inputs)
Serial Port #1
RS-232 (Tx, Rx, GND)
Serial Port #2
RS-485
Antenna Connector Mobile (EC350 only)
SMA female
Antenna Connector GPS (EC350 only)
SMA female (acƟ ve or passive antenna)
USB Interface
Micro USB, USB 2.0
Protocols
Modbus RTU
MounƟ ng
DIN rail (EN 50022)
Wall mounƟ ng
Dimensions (H x W x D)
25.6 x 135 x 92 mm
Temperature
OperaƟ ng: -40 °C to +65 °C
Storage: -45 °C to +85 °C
Humidity range
5–95 % RH, non-condensing
Input Voltage
12–48 VDC
Recommended Power Supply
24 VDC, 25 W, LPS
Power ConsumpƟ on, typical
EC310: 2.5 W
EC350: 4.5 W
CerƟ fi caƟ ons
EC310: CE,
CULUS
EC350: CE, CULUS, FCC, IC, PTCRB
Contains FCC ID: QIPPHS8-P
Contains IC ID: 7380A-PHS8P
R323
2
To maintain CE compliance, DC cable
length must not exceed 3 meters and
shielded Ethernet cables must be used.
Loading...