Operating instructions
EN
Intermediate drive unit
miniDrive GS
miniDrive WS
099-005262-EW501
Observe additional system documents!
22.11.2016
Register now
and benefit!
Jetzt Registrieren
und Profitieren!
www.ewm-group.com
*For details visit
www.ewm-group.com
*
General instructions
WARNING
Read the operating instructions!
The operating instructions provide an introduction to the safe use of the products.
• Read and observe the operating instructions for all system components, especially the
safety instructions and warning notices!
• Observe the accident prevention regulations and any regional regulations!
• The operating instructions must be kept at the location where the machine is operated.
• Safety and warning labels on the machine indicate any possible risks.
Keep these labels clean and legible at all times.
• The machine has been constructed to state-of-the-art standards in line with any applicable
regulations and industrial standards. Only trained personnel may operate, service and
repair the machine.
• Technical changes due to further development in machine technology may lead to a
differing welding behaviour.
In the event of queries on installation, commissioning, operation or special conditions at the
installation site, or on usage, please contact your sales partner or our customer service
department on +49 2680 181-0.
A list of authorised sales partners can be found at www.ewm-group.com.
Liability relating to the operation of this equipment is restricted solely to the function of the
equipment. No other form of liability, regardless of type, shall be accepted. This exclusion of
liability shall be deemed accepted by the user on commissioning the equipment.
The manufacturer is unable to monitor whether or not these instructions or the conditions and
methods are observed during installation, operation, usage and maintenance of the equipment.
An incorrectly performed installation can result in material damage and injure persons as a
result. For this reason, we do not accept any responsibility or liability for losses, damages or
costs arising from incorrect installation, improper operation or incorrect usage and maintenance
or any actions connected to this in any way.
© EWM AG
Dr. Günter-Henle-Straße 8
56271 Mündersbach
Germany
The copyright to this document remains the property of the manufacturer.
Copying, including extracts, only permitted with written approval.
The content of this document has been prepared and reviewed with all reasonable care. The information
provided is subject to change; errors excepted.
Contents
Notes on the use of these operating instructions
099-005262-EW501
22.11.2016
3
1 Contents
1 Contents .................................................................................................................................................. 3
2 For your safety ....................................................................................................................................... 5
2.1 Notes on the use of these operating instructions .......................................................................... 5
2.1.1 Explanation of icons ....................................................................................................... 6
2.2 Part of the complete documentation .............................................................................................. 7
3 Intended use ........................................................................................................................................... 8
3.1 Use and operation solely with the following machines .................................................................. 8
3.2 Documents which also apply ......................................................................................................... 9
3.2.1 Warranty ......................................................................................................................... 9
3.2.2 Declaration of Conformity ............................................................................................... 9
3.2.3 Service documents (spare parts and circuit diagrams) .................................................. 9
3.2.4 Calibration/Validation ..................................................................................................... 9
4 Machine description – quick overview .............................................................................................. 10
4.1 Front view .................................................................................................................................... 10
4.2 Inside view ................................................................................................................................... 11
5 Design and function ............................................................................................................................. 12
5.1 Transport and installation ............................................................................................................ 12
5.1.1 Ambient conditions ....................................................................................................... 12
5.1.1.1 In operation ................................................................................................... 12
5.1.1.2 Transport and storage ................................................................................... 12
5.1.2 Machine cooling ............................................................................................................ 13
5.1.3 Workpiece lead, general ............................................................................................... 13
5.1.4 Welding torch cooling system ....................................................................................... 14
5.1.4.1 Approved coolants overview ......................................................................... 14
5.1.4.2 Maximal hose package length ...................................................................... 14
5.1.5 Notes on the installation of welding current leads ........................................................ 15
5.1.5.1 Stray welding currents................................................................................... 16
5.2 Preparing the welding system ...................................................................................................... 17
5.2.1 Switching between Push/Pull and intermediate drive .................................................. 17
5.3 Welding torch connection ............................................................................................................ 18
5.4 Hose package/intermediate drive connection .............................................................................. 19
5.5 Wire feed ...................................................................................................................................... 20
5.5.1 Open the protective flap of the wire feeder .................................................................. 20
5.5.2 Changing the wire feed rollers ...................................................................................... 20
5.5.3 Inching the wire electrode ............................................................................................ 21
5.6 Setting the operating point (welding output) ................................................................................ 23
5.7 Replacing the steel liner in the hose package ............................................................................. 24
6 Maintenance, care and disposal ......................................................................................................... 26
6.1 General ........................................................................................................................................ 26
6.2 Cleaning ....................................................................................................................................... 26
6.3 Maintenance work, intervals ........................................................................................................ 27
6.3.1 Daily maintenance tasks .............................................................................................. 27
6.3.1.1 Visual inspection ........................................................................................... 27
6.3.1.2 Functional test ............................................................................................... 27
6.3.2 Monthly maintenance tasks .......................................................................................... 27
6.3.2.1 Visual inspection ........................................................................................... 27
6.3.2.2 Functional test ............................................................................................... 27
6.3.3 Annual test (inspection and testing during operation) .................................................. 28
6.4 Disposing of equipment ............................................................................................................... 28
6.4.1 Manufacturer's declaration to the end user .................................................................. 28
6.5 Meeting the requirements of RoHS ............................................................................................. 28
7 Rectifying faults ................................................................................................................................... 29
7.1 Checklist for rectifying faults ........................................................................................................ 29
7.2 Vent coolant circuit ....................................................................................................................... 30
8 Technical data ...................................................................................................................................... 31
Contents
Notes on the use of these operating instructions
4
099-005262-EW501
22.11.2016
8.1 miniDrive ...................................................................................................................................... 31
9 Accessories .......................................................................................................................................... 32
9.1 Remote control / connection cable ............................................................................................... 32
9.2 General accessories .................................................................................................................... 32
10 Replaceable parts ................................................................................................................................. 33
10.1 Conversion kit .............................................................................................................................. 33
10.2 Wire feed rollers ........................................................................................................................... 33
10.2.1 Wire feed rollers for steel wire ...................................................................................... 33
10.2.2 Wire feed rollers for aluminium wire ............................................................................. 33
11 Appendix A ............................................................................................................................................ 34
11.1 Circuit diagram – cable adapter ................................................................................................... 34
12 Appendix B ............................................................................................................................................ 35
12.1 Overview of EWM branches......................................................................................................... 35
For your safety
Notes on the use of these operating instructions
099-005262-EW501
22.11.2016
5
2 For your safety
2.1 Notes on the use of these operating instructions
DANGER
Working or operating procedures which must be closely observed to prevent imminent
serious and even fatal injuries.
• Safety notes include the "DANGER" keyword in the heading with a general warning symbol.
• The hazard is also highlighted using a symbol on the edge of the page.
WARNING
Working or operating procedures which must be closely observed to prevent serious
and even fatal injuries.
• Safety notes include the "WARNING" keyword in the heading with a general warning
symbol.
• The hazard is also highlighted using a symbol in the page margin.
CAUTION
Working or operating procedures which must be closely observed to prevent possible
minor personal injury.
• The safety information includes the "CAUTION" keyword in its heading with a general
warning symbol.
• The risk is explained using a symbol on the edge of the page.
Special technical points which users must observe.
Instructions and lists detailing step-by-step actions for given situations can be recognised via bullet
points, e.g.:
• Insert the welding current lead socket into the relevant socket and lock.
For your safety
Notes on the use of these operating instructions
6
099-005262-EW501
22.11.2016
2.1.1 Explanation of icons
Symbol
Description
Symbol
Description
Indicates technical aspects which the
user must observe.
Activate and release/tap/tip
Switch off machine
Release
Switch on machine
Press and keep pressed
Switch
Wrong
Turn
Correct
Numerical value – adjustable
Menu entry
Signal light lights up in green
Navigating the menu
Signal light flashes green
Exit menu
Signal light lights up in red
Time representation (e.g.: wait
4 s/activate)
Signal light flashes red
Interruption in the menu display (other
setting options possible)
Tool not required/do not use
Tool required/use
For your safety
Part of the complete documentation
099-005262-EW501
22.11.2016
7
2.2 Part of the complete documentation
These operating instructions are part of the complete documentation and valid only in
combination with all other parts of these instructions! Read and observe the operating
instructions for all system components, especially the safety instructions!
The illustration shows a general example of a welding system.
Figure 2-1
Item
Documentation
A.1
Wire feeder
A.2
Conversion instructions
A.3
Power source
A.4
Cooling unit, voltage converter, tool box etc.
A.5
Trolley
A.6
Welding torch
A.7
Remote control
A.8
Control
A
Complete documentation
Intended use
Use and operation solely with the following machines
8
099-005262-EW501
22.11.2016
3 Intended use
WARNING
Hazards due to improper usage!
The machine has been constructed to the state of the art and any regulations and
standards applicable for use in industry and trade. It may only be used for the welding
procedures indicated at the rating plate. Hazards may arise for persons, animals and
material objects if the equipment is not used correctly. No liability is accepted for any
damages arising from improper usage!
• The equipment must only be used in line with its designated purpose and by trained or
expert personnel!
• Do not improperly modify or convert the equipment!
Wire feeder (intermediate drive) for welding wire electrodes used for gas-shielded metal-arc welding and
hose packages of up to 25 m.
3.1 Use and operation solely with the following machines
A compact or decompact system component with wire feeder is required to operate the
intermediate drive.
In addition, the system component has to be equipped with a current M 3.7X-X variant machine
control (three digital displays).
The following machine series can be combined with the intermediate drive:
• Taurus Synergic S
• Phoenix
• alpha Q
All compact 355 TKM and 355 TKWmachines in the relevant series are excluded.
Intended use
Documents which also apply
099-005262-EW501
22.11.2016
9
3.2 Documents which also apply
3.2.1 Warranty
For more information refer to the "Warranty registration" brochure supplied and our information
regarding warranty, maintenance and testing at www.ewm-group.com!
3.2.2 Declaration of Conformity
The labelled machine complies with the following EC directives in terms of its design and
construction:
• Low Voltage Directive (LVD)
• Electromagnetic Compatibility Directive (EMC)
• Restriction of Hazardous Substance (RoHS)
In case of unauthorised changes, improper repairs, non-compliance with specified deadlines for "Arc
Welding Equipment – Inspection and Testing during Operation", and/or prohibited modifications which
have not been explicitly authorised by EWM, this declaration shall be voided. An original document of the
specific declaration of conformity is included with every product.
3.2.3 Service documents (spare parts and circuit diagrams)
WARNING
Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.
• Appoint only skilled persons for repair work (trained service personnel)!
Original copies of the circuit diagrams are enclosed with the unit.
Spare parts can be obtained from the relevant authorised dealer.
3.2.4 Calibration/Validation
We hereby confirm that this machine has been tested using calibrated measuring equipment, as
stipulated in IEC/EN 60974, ISO/EN 17662, EN 50504, and complies with the admissible tolerances.
Recommended calibration interval: 12 months
Machine description – quick overview
Front view
10
099-005262-EW501
22.11.2016
4 Machine description – quick overview
4.1 Front view
Connections and operating elements for torch cooling only with correspondent machine
versions.
Figure 4-1
Item
Symbol
Description 0
1 Carrying handle
2 Wire speed rotary dial
Infinitely adjustable setting of the wire speed from min. to max.
(welding output, one-dial operation)
3 Rotary dial, Arc length correction
Arc length correction from -10 V to + 10 V
4 Quick connect coupling (red)
coolant return
5 Quick connect coupling (blue)
coolant supply
6 19-pole connection socket (analogue)
For connecting analogue accessory components (remote control, welding torch control
lead, etc.)
7 Welding torch connection (Euro torch connector)
Welding current, shielding gas and torch trigger integrated
Machine description – quick overview
Inside view
099-005262-EW501
22.11.2016
11
4.2 Inside view
Figure 4-2
Item
Symbol
Description 0
1 Slide latch, lock for the protective cap
2 Protective cap
Cover for the wire feed mechanism and other operating elements.
Depending on the machine series, additional stickers with information on the
replacement parts and JOB lists will be located on the inside.
3 Changeover switch, remote control on/off
ON Set the welding performance via the remote control
OFF Set the welding performance via the machine control
4 Wire feed unit
5 Intermediate hose package
6 Push-button, wire inching
Potential- and gas-free inching of the wire electrode through the hose package to the
welding torch > see 5.5.3 chapter.
The inching speed is infinitely adjustable by simultaneously pressing the wire inching pushbutton and turning the wire speed rotary knob.
Design and function
Transport and installation
12
099-005262-EW501
22.11.2016
5 Design and function
WARNING
Risk of injury from electric shock!
Contact with live parts, e.g. welding current sockets, is potentially fatal!
• Follow safety instructions on the opening pages of the operating instructions.
• Commissioning may only be carried out by persons who have the relevant expertise of
working with arc welding machines!
• Connection and welding leads (e.g. electrode holder, welding torch, workpiece lead,
interfaces) may only be connected when the machine is switched off!
5.1 Transport and installation
WARNING
Risk of accident due to improper transport of machines that must not be lifted!
Do not lift or suspend the machine! The machine can drop and cause injuries! The
handles, straps or brackets are suitable for transport by hand only!
• The machine must not be suspended or lifted using a crane.
Read and observe the documentation to all system and accessory components!
5.1.1 Ambient conditions
T he machine must not be operated in the open air and must only be set up and operated on a
suitable, stable and level base!
• The operator must ensure that the ground is non-slip and level, and provide sufficient lighting
for the place of work.
• Safe operation of the machine must be guaranteed at all times.
Unusually high quantities of dust, acid, corrosive gases or substances may damage the
equipment.
• Avoid high volumes of smoke, vapour, oil vapour and grinding dust!
• Avoid ambient air containing salt (sea air)!
5.1.1.1 In operation
Temperature range of the ambient air:
• -25 °C to +40 °C
Relative air humidity:
• Up to 50% at 40 °C
• Up to 90% at 20 °C
5.1.1.2 Transport and storage
Storage in an enclosed space, temperature range of the ambient air:
• -30 °C to +70 °C
Relative air humidity
• Up to 90% at 20 °C
Design and function
Transport and installation
099-005262-EW501
22.11.2016
13
5.1.2 Machine cooling
Insufficient ventilation results in a reduction in performance and equipment damage.
• Observe the ambient conditions!
• Keep the cooling air inlet and outlet clear!
• Observe the minimum distance of 0.5 m from obstacles!
5.1.3 Workpiece lead, general
CAUTION
Risk of burning due to incorrect welding current connection!
If the welding current plugs (machine connections) are not locked or if the workpiece
connection is contaminated (paint, corrosion), these connections and leads can heat up
and cause burns when touched!
• Check welding current connections on a daily basis and lock by turning to the right when
necessary.
• Clean workpiece connection thoroughly and secure properly. Do not use structural parts of
the workpiece as welding current return lead!
Design and function
Transport and installation
14
099-005262-EW501
22.11.2016
5.1.4 Welding torch cooling system
Insufficient frost protection in the welding torch coolant!
Depending on the ambient conditions, different liquids are used for cooling the welding
torch > see 5.1.4.1 chapter.
Coolants with frost protection (KF 37E or KF 23E) must be checked regularly to ensure that the
frost protection is adequate to prevent damage to the machine or the accessory components.
• The coolant must be checked for adequate frost protection with the TYP 1 frost protection
tester .
• Replace coolant as necessary if frost protection is inadequate!
Coolant mixtures!
Mixtures with other liquids or the use of unsuitable coolants result in material damage and
renders the manufacturer's warranty void!
• Only use the coolant described in this manual (overview of coolants).
• Do not mix different coolants.
• When changing the coolant, the entire volume of liquid must be changed.
Dispose of the coolant in accordance with local regulations and the material safety data sheets
(German waste code number: 70104).
May not be disposed of in household waste.
Prevent entry into sewers.
Absorb with liquid-binding material (sand, gravel, acid-binding agents, universal binding agents,
sawdust).
5.1.4.1 Approved coolants overview
Coolant
Temperature range
KF 23E (Standard)
-10 °C to +40 °C
KF 37E
-20 °C to +10 °C
5.1.4.2 Maximal hose package length
Pump 3.5 bar
Pump 4.5 bar
Machines with or without separate wire feeder
30 m
60 m
Compact machines with additional intermediate
drive (example. miniDrive)
20 m
30 m
Machines with separate wire feeder and additional
intermediate drive (example: miniDrive)
20 m
60 m
Data as a rule refer to the entire hose package length
including welding torch. The pump output is shown on the type plate (parameter: Pmax).
Pump 3.5 bar: Pmax = 0.35 MPa (3.5 bar)
Pump 4.5 bar: Pmax = 0.45 MPa (4.5 bar)
Design and function
Transport and installation
099-005262-EW501
22.11.2016
15
5.1.5 Notes on the installation of welding current leads
Incorrectly installed welding current leads can cause faults in the arc (flickering).
Lay the workpiece lead and hose package of power sources without HF igniter (MIG/MAG) for as
long and as close as possible in parallel.
Lay the workpiece lead and hose package of power sources with HF igniter (TIG) for as long as
possible in parallel with a distance of 20 cm to avoid HF sparkover.
Always keep a distance of at least 20 cm to leads of other power sources to avoid interferences
Always keep leads as short as possible! For optimum welding results max. 30 m (welding lead +
intermediate hose package + torch lead).
Figure 5-1
Use an individual welding lead to the workpiece for each welding machine!
Figure 5-2
Design and function
Transport and installation
16
099-005262-EW501
22.11.2016
Fully unroll welding current leads, torch hose packages and intermediate hose packages. Avoid
loops!
Always keep leads as short as possible!
Lay any excess cable lengths in meanders.
Figure 5-3
5.1.5.1 Stray welding currents
WARNING
Risk of injury due to stray welding currents!
Stray welding currents can destroy protective earth conductors, damage machines and
electronic devices and cause overheating of components, leading to fire.
• Check that all welding current connections are firmly secured and electrical connections are
in perfect condition.
• Set up, attach or suspend all conductive power source components such as casing,
transport vehicles and crane frames so they are insulated.
• Do not place any other electronic devices such as drills or angle grinders on the power
source, transport vehicle or crane frames unless they are insulated.
• Always put welding torches and electrode holders on an insulated surface when they are
not in use.
Figure 5-4
Design and function
Preparing the welding system
099-005262-EW501
22.11.2016
17
5.2 Preparing the welding system
5.2.1 Switching between Push/Pull and intermediate drive
WARNING
Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.
• Appoint only skilled persons for repair work (trained service personnel)!
The wire feeder used in the welding system has to be modified for use with an intermediate drive. To do
so, unscrew the casing cover and perform the following two actions on PCB M370/1:
Replug the connector (X23/X24)
Plug
Function
On X24
Use with push/pull welding torch (ex factory)
On X23
Use with intermediate drive
Install cable adapter
The cable adapter (included with the intermediate drive) has to be added to the wire feeder cable
harness.
The cable adapter has to be plugged in at three locations (X2, X3 and X5) between the relevant PCB
connections and cable plugs (see attached circuit diagram > see 11.1 chapter):
• PCB M370/1, connection X2 (18-pole)
• PCB M370/1, connection X3 (2-pole)
• PCB M370/1, connection X5 (12-pole)
Figure 5-5
Test!
Before re-commissioning, it is essential that an "inspection and test during operation" is carried
out conforming to IEC / DIN EN 60974-4 "Arc welding devices - inspection and testing during
operation"!
• For detailed instructions, please see the standard operating instructions for the welding
machine.
Design and function
Welding torch connection
18
099-005262-EW501
22.11.2016
5.3 Welding torch connection
Equipment damage due to improperly connected coolant pipes!
If the coolant pipes are not properly connected or a gas-cooled welding torch is used, the coolant
circuit is interrupted and equipment damage can occur.
• Connect all coolant pipes correctly!
• Completely unroll the hose package and the torch hose package!
• Observe maximal hose package length > see 5.1.4.2 chapter.
• When using a gas-cooled welding torch, use a hose bridge to establish the coolant
circuit > see 9 chapter.
On delivery, the Euro torch connector is fitted with a capillary tube for welding torches with a
steel liner. Conversion is necessary if a welding torch with a liner is used!
• Operate welding torches with a liner > with a guide tube.
• Operate welding torches with a steel liner > with a capillary tube.
Depending on the wire electrode diameter or type, either a steel liner or liner with the correct inner
diameter must be inserted in the torch!
Recommendation:
• Use a steel liner when welding hard, unalloyed wire electrodes (steel).
• Use a chrome nickel liner when welding hard, high-alloy wire electrodes (CrNi).
• Use a plastic or teflon liner when welding or brazing soft wire electrodes, high-alloy wire electrodes or
aluminium materials.
Preparation for connecting welding torches with a liner:
• Push forward the capillary tube on the wire feed side in the direction of the Euro torch connector and
remove it there.
• Insert the liner guide tube from the Euro torch connector side.
• Carefully insert the welding torch connector with as yet too long a liner into the Euro torch connector
and secure with a crown nut.
• Cut off the liner with a liner cutter > see 9 chapter just before the wire feed roller.
• Loosen the welding torch connector and remove.
• Carefully chamfer the cut off end of the liner with a liner sharpener > see 9 chapter and sharpen.
Design and function
Hose package/intermediate drive connection
099-005262-EW501
22.11.2016
19
Figure 5-6
Item
Symbol
Description 0
1 Welding torch
2 Welding torch hose package
3 Welding torch connection (Euro torch connector)
Welding current, shielding gas and torch trigger integrated
4 Quick connect coupling (red)
coolant return
5 19-pole connection socket (analogue)
For connecting analogue accessory components (remote control, welding torch control
lead, etc.)
6 Quick connect coupling (blue)
coolant supply
• Insert the central plug for the welding torch into the central connector and screw together with crown
nut.
Where applicable:
• Insert the welding torch control cable into the 19-pole connection socket and lock (MIG/MAG torches
with additional control cables only).
• Lock connecting nipples of the cooling water tubes into the corresponding quick connect couplings:
Return line red to quick connect coupling, red (coolant return) and
supply line blue to quick connect coupling, blue (coolant supply).
5.4 Hose package/intermediate drive connection
• Insert central connector of the intermediate hose package into the Euro torch connector of the relevant
wire feeder (compact or decompact system component) and secure with crown nut.
Read and observe the documentation to all system and accessory components!
Design and function
Wire feed
20
099-005262-EW501
22.11.2016
5.5 Wire feed
5.5.1 Open the protective flap of the wire feeder
To perform the following steps, the protective flap of the wire feeder needs to be opened. Make
sure to close the protective flap again before starting to work.
• Unlock and open protective flap.
5.5.2 Changing the wire feed rollers
Unsatisfactory welding results due to faulty wire feeding!
Wire feed rollers must be suitable for the diameter of the wire and the material.
• Check the roller label to verify that the rollers are suitable for the wire diameter. Turn or
change if necessary!
• use V-groove rollers with for steel wires and other hard wires.
• Slide new drive rollers into place so that the diameter of the wire used is visible on the drive roller.
• Screw the drive rollers in place with knurled screws.
Figure 5-7
Design and function
Wire feed
099-005262-EW501
22.11.2016
21
5.5.3 Inching the wire electrode
CAUTION
Risk of injury due to moving parts!
The wire feeders are equipped with moving parts, which can trap hands, hair, clothing
or tools and thus injure persons!
• Do not reach into rotating or moving parts or drive components!
• Keep casing covers or protective caps closed during operation!
Risk of injury due to welding wire escaping in an unpredictable manner!
Welding wire can be conveyed at very high speeds and, if conveyed incorrectly, may
escape in an uncontrolled manner and injure persons!
• Before mains connection, set up the complete wire guide system from the wire spool to the
welding torch!
• Check wire guide at regular intervals!
• Keep all casing covers or protective caps closed during operation!
Risk of injury due to welding wire escaping from the welding torch!
The welding wire can escape from the welding torch at high speed and cause bodily
injury including injuries to the face and eyes!
• Never direct the welding torch towards your own body or towards other persons!
Incorrect contact pressure will cause extensive wear of the wire feed rollers!
• With the adjusting nuts of the pressure units set the contact pressure so that the wire
electrode is conveyed but will still slip through if the wire spool jams.
• Set the contact pressure of the front rollers (in wire feed direction) to a higher value!
Design and function
Wire feed
22
099-005262-EW501
22.11.2016
Figure 5-8
Item
Symbol
Description 0
1 Adjusting nut
2 Clamping unit
3 Pressure roller
4 Drive roller
5 Knurled screw
6 Wire feed nipple
7 Feed roll tensioner
Fixing the clamping unit and setting the pressure.
• Extend and lay out the torch hose package.
• Flip feed roll tensioner down towards user (clamping unit will be released)
• Fold tensioning device up
• Carefully introduce the welding wire from the inlet guide through the drive roll grooves into the capillary
tube or teflon liner with wire guide tube.
• Press the tensioning device back down and secure by folding the feed roll tensioner up (wire electrode
should be in the groove on the drive roller)
• Set the contact pressure with the adjusting nuts of the feed roll tensioner
• Press the wire inching button until the wire electrode projects out of the welding torch.
The inching speed is infinitely adjustable by simultaneously pressing the wire inching pushbutton and turning the wire speed rotary knob. The left display shows the wire feed speed
selected, the right display shows the current motor current of the wire feed mechanism.
Design and function
Setting the operating point (welding output)
099-005262-EW501
22.11.2016
23
5.6 Setting the operating point (welding output)
The operating point (welding power) is specified using the MIG/MAG one-knob operation principle, i.e. the
user can specify either the welding current, the wire feed speed or the material thickness to define the
operating point. The electronic system calculates the optimal required welding voltage value.
Operating
element
Action
Result
Operating point setting via wire speed.
The arc length can be corrected as follows.
Operating
element
Action
Result
Arc length correction
Design and function
Replacing the steel liner in the hose package
24
099-005262-EW501
22.11.2016
5.7 Replacing the steel liner in the hose package
Always make sure the the hose package is straight when replacing the wire guide.
Figure 5-9
Item
Symbol
Description 0
1 Allen key (size 2.5)
2 Headless screw
3 Threaded hole
4 Steel liner
• Unscrew the headless screw using an Allen key (to release the steel liner from the wire feed
mechanism)
Design and function
Replacing the steel liner in the hose package
099-005262-EW501
22.11.2016
25
Figure 5-10
Item
Symbol
Description 0
1 Open-ended spanner, SW 11
2 Crown nut
3 Euro central connection
Welding current, shielding gas and torch trigger included
• Loosen the crown nut of the liner fastening
• Pull out steel liner
Due to production tolerances the steel liner length has to be adapted to the hose package used.
• Place new and old steel liner in parallel
• Shorten new steel liner to the total length of the old one
• Insert new steel liner into the Euro torch connector as far as it goes (the steel liner has to be visible
inside the headless screw threaded hole)
• Retighten the crown nut of the liner fastening
• Screw headless screw back in using the Allen key (max. torque 2 Nm)
Maintenance, care and disposal
General
26
099-005262-EW501
22.11.2016
6 Maintenance, care and disposal
6.1 General
DANGER
Incorrect maintenance and testing!
The machine may be cleaned, repaired and tested by skilled and qualified personnel
only. A qualified person is one who, due to their training, knowledge and experience,
can detect any hazards and possible consequential damage when checking the
machine, and can take the necessary safety measures.
• Observe the maintenance instructions > see 6.3 chapter!
• The machine may only be put into operation again once the testing has been successful.
Risk of injury due to electrical voltage after switching off!
Working on an open machine can lead to fatal injuries!
Capacitors are loaded with electrical voltage during operation. Voltage remains present
for up to four minutes after the mains plug is removed.
1. Switch off machine.
2. Remove the mains plug.
3. Wait for at last 4 minutes until the capacitors have discharged!
WARNING
Cleaning, testing and repair!
Cleaning, testing and repairing of the welding machine may only be carried out by
competent, qualified personnel. A qualified person is one who, because of his or her
training, knowledge and experience, is able to recognise the dangers that can occur
while testing welding power sources as well as possible subsequent damage, and who is
able to implement the required safety procedures.
• In the event of failure of any one of the following tests, the machine must not be operated
again until it has been repaired and a new test has been carried out.
Repair and maintenance work may only be performed by qualified authorised personnel; otherwise the
right to claim under warranty is void. In all service matters, always consult the dealer who supplied the
machine. Return deliveries of defective equipment subject to warranty may only be made through your
dealer. When replacing parts, use only original spare parts. When ordering spare parts, please quote the
machine type, serial number and item number of the machine, as well as the type designation and item
number of the spare part.
Under the specified ambient conditions and normal working conditions this machine is essentially
maintenance-free and requires just a minimum of care.
Contamination of the machine may impair service life and duty cycle. The cleaning intervals depend on
the ambient conditions and the resulting contamination of the machine. The minimum interval is every six
months.
6.2 Cleaning
• Clean the outer surfaces with a moist cloth (no aggressive cleaning agents).
• Purge the machine venting channel and cooling fins (if present) with oil- and water-free compressed
air. Compressed air may overspeed and destroy the machine fans. Never direct the compressed air
directly at the machine fans. Mechanically block the fans, if required.
• Check the coolant for contaminants and replace, if necessary.
Maintenance, care and disposal
Maintenance work, intervals
099-005262-EW501
22.11.2016
27
6.3 Maintenance work, intervals
Repair and maintenance work may only be performed by qualified authorised personnel; otherwise the
right to claim under warranty is void. In all service matters, always consult the dealer who supplied the
machine. Return deliveries of defective equipment subject to warranty may only be made through your
dealer. When replacing parts, use only original spare parts. When ordering spare parts, please quote the
machine type, serial number and item number of the machine, as well as the type designation and item
number of the spare part.
6.3.1 Daily maintenance tasks
6.3.1.1 Visual inspection
• Mains supply lead and its strain relief
• Gas cylinder securing elements
• Check hose package and power connections for exterior damage and replace or have repaired by
specialist staff as necessary!
• Gas tubes and their switching equipment (solenoid valve)
• Check that all connections and wearing parts are hand-tight and tighten if necessary.
• Check correct mounting of the wire spool.
• Wheels and their securing elements
• Transport elements (strap, lifting lugs, handle)
• Other, general condition
6.3.1.2 Functional test
• Operating, message, safety and adjustment devices (Functional test)
• Welding current cables (check that they are fitted correctly and secured)
• Gas tubes and their switching equipment (solenoid valve)
• Gas cylinder securing elements
• Check correct mounting of the wire spool.
• Check that all screw and plug connections and replaceable parts are secured correctly, tighten if
necessary.
• Remove any spatter.
• Clean the wire feed rollers on a regular basis (depending on the degree of soiling).
6.3.2 Monthly maintenance tasks
6.3.2.1 Visual inspection
• Casing damage (front, rear and side walls)
• Wheels and their securing elements
• Transport elements (strap, lifting lugs, handle)
• Check coolant tubes and their connections for impurities
6.3.2.2 Functional test
• Selector switches, command devices, emergency stop devices, voltage reducing devices, message
and control lamps
• Check that the wire guide elements (inlet nipple, wire guide tube) are fitted securely.
• Check coolant tubes and their connections for impurities
• Check and clean the welding torch. Deposits in the torch can cause short circuits and have a negative
impact on the welding result, ultimately causing damage to the torch.
Maintenance, care and disposal
Disposing of equipment
28
099-005262-EW501
22.11.2016
6.3.3 Annual test (inspection and testing during operation)
The welding machine may only be tested by competent, capable personsl. A capable person is
one who, because of his training, knowledge and experience, is able to recognise the dangers
that can occur while testing welding power sources as well as possible subsequent damage and
who is able to implement the required safety procedures.
For more information refer to the "Warranty registration" brochure supplied and our information
regarding warranty, maintenance and testing at www.ewm-group.com!
A periodic test according to IEC 60974-4 "Periodic inspection and test" has to be carried out. In addition
to the regulations on testing given here, the relevant local laws and regulations must also be observed.
6.4 Disposing of equipment
Proper disposal!
The machine contains valuable raw materials, which should be recycled, and electronic
components, which must be disposed of.
• Do not dispose of in household waste!
• Observe the local regulations regarding disposal!
6.4.1 Manufacturer's declaration to the end user
• According to European provisions (guideline 2012/19/EU of the European Parliament and the Council
of Juli, 4th 2021), used electric and electronic equipment may no longer be placed in unsorted
municipal waste. It must be collected separately. The symbol depicting a waste container on wheels
indicates that the equipment must be collected separately.
This machine is to be placed for disposal or recycling in the waste separation systems provided for
this purpose.
• According to German law (law governing the distribution, taking back and environmentally correct
disposal of electric and electronic equipment (ElektroG) from 16.03.2005), used machines are to be
placed in a collection system separate from unsorted municipal waste. The public waste management
utilities (communities) have created collection points at which used equipment from private
households can be disposed of free of charge.
• Information about giving back used equipment or about collections can be obtained from the
respective municipal administration office.
• EWM participates in an approved waste disposal and recycling system and is registered in the Used
Electrical Equipment Register (EAR) under number WEEE DE 57686922.
• In addition to this, returns are also possible throughout Europe via EWM sales partners.
6.5 Meeting the requirements of RoHS
We, EWM AG in Mündersbach, Germany, hereby confirm that all products which we supply to you and
that are subject to the RoHS directive comply with RoHS requirements (also see applicable EC directives
on the Declaration of Conformity on your machine).
Rectifying faults
Checklist for rectifying faults
099-005262-EW501
22.11.2016
29
7 Rectifying faults
All products are subject to rigorous production checks and final checks. If, despite this, something fails to
work at any time, please check the product using the following flowchart. If none of the fault rectification
procedures described leads to the correct functioning of the product, please inform your authorised
dealer.
7.1 Checklist for rectifying faults
The correct machine equipment for the material and process gas in use is a fundamental
requirement for perfect operation!
Legend
Symbol
Description
Fault/Cause
Remedy
Coolant error/no coolant flowing
Insufficient coolant flow
Check coolant level and refill if necessary
Air in the coolant circuit
Vent coolant circuit > see 7.2 chapter
Wire feed problems
Contact tip blocked
Clean, spray with anti-spatter spray and replace if necessary
Setting the spool brake
Check settings and correct if necessary
Setting pressure units > see 5.5.3 chapter
Check settings and correct if necessary
Worn wire rolls
Check and replace if necessary
Wire feed motor without supply voltage (automatic cutout triggered by overloading)
Reset triggered fuse (rear of the power source) by pressing the key button
Kinked hose packages
Extend and lay out the torch hose package
Wire guide core or spiral is dirty or worn
Clean core or spiral; replace kinked or worn cores
Functional errors
All machine control signal lights are illuminated after switching on
No machine control signal light is illuminated after switching on
No welding power
Phase failure > check mains connection (fuses)
Various parameters cannot be set
Entry level is blocked, disable access lock
Connection problems
Make control lead connections and check that they are fitted correctly.
Loose welding current connections
Tighten power connections on the torch and/or on the workpiece
Tighten contact tip correctly
Rectifying faults
Vent coolant circuit
30
099-005262-EW501
22.11.2016
7.2 Vent coolant circuit
Coolant tank and quick connect coupling of coolant supply and return are only fitted in machines
with water cooling.
To vent the cooling system always use the blue coolant connection, which is located as deep as
possible inside the system (close to the coolant tank)!
Figure 7-1
Technical data
miniDrive
099-005262-EW501
22.11.2016
31
8 Technical data
Performance specifications and guarantee only in connection with original spare and
replacement parts!
8.1 miniDrive
Supply voltage
60 VDC
Max. welding current (100% DC)
300 A
Max. welding current (60% DC)
400 A
Wire feed speed
1 m/min–20 m/min
Standard roll installation
1.0 + 1.2 mm (for steel wire)
Drive rolls
37 mm
Euro torch connector
Euro torch connector
Protection classification
IP 23
Ambient temperature
-25 °C to +40 °C
EMC class
A
Safety identification
/
Harmonised standards used
IEC 60974-1, -5, -10
Dimensions L x W x H
300 mm x 180 mm x 200 mm
Weight excl. hose package
7.5 kg
Accessories
Remote control / connection cable
32
099-005262-EW501
22.11.2016
9 Accessories
Performance-dependent accessories like torches, workpiece leads, electrode holders or
intermediate hose packages are available from your authorised dealer.
9.1 Remote control / connection cable
Type
Designation
Item no.
R10 19POL
Remote control
090-008087-00000
RG10 19POL 5M
Remote control to set the wire speed and welding
voltage correction
090-008108-00000
R20 19POL
Program changeover remote control
090-008263-00000
RA5 19POL 5M
Remote control e.g. connection cable
092-001470-00005
RA10 19POL 10M
Remote control e.g. connection cable
092-001470-00010
9.2 General accessories
Type
Designation
Item no.
SPL
Sharpener for plastic liners
094-010427-00000
HC PL
Hose cutter
094-016585-00000
Replaceable parts
Conversion kit
099-005262-EW501
22.11.2016
33
10 Replaceable parts
The manufacturer's warranty becomes void if non-genuine parts are used!
• Only use system components and options (power sources, welding torches, electrode
holders, remote controls, spare parts and replacement parts, etc.) from our range of products!
• Only insert and lock accessory components into the relevant connection socket when the
machine is switched off.
10.1 Conversion kit
Type
Designation
Item no.
URUE AL 2R 10m miniDrive
Conversion kit for aluminium consisting of two drive
pinions, liner and mounting material
092-007906-00010
URUE AL 2R 15m miniDrive
Conversion kit for aluminium consisting of two drive
pinions, liner and mounting material
092-007906-00015
10.2 Wire feed rollers
10.2.1 Wire feed rollers for steel wire
Type
Designation
Item no.
FE 1DR2R 0.8+1.0
Drive rollers, 37mm, steel
094-003218-00000
FE 1DR2R 0.9+1.2
Drive rollers, 37mm, steel
094-003221-00000
FE 1DR2R 1.0+1.2
Drive rollers, 37mm, steel
094-003219-00000
FE 1DR2R 1,2+1,6
Drive rollers, 37 mm, steel
094-003220-00000
FE GR2R
Pressure roller, smooth, 37 mm
092-007908-00000
10.2.2 Wire feed rollers for aluminium wire
Type
Designation
Item no.
AL 2ZR2R 1,2+1,6
Twin wire feed rollers, 37 mm, for aluminium
092-000829-00000
Figure 10-1
Appendix A
Circuit diagram – cable adapter
34
099-005262-EW501
22.11.2016
11 Appendix A
11.1 Circuit diagram – cable adapter
WARNING
Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.
• Appoint only skilled persons for repair work (trained service personnel)!
Configuration > see 5.2.1 chapter
Figure 11-1
Appendix B
Overview of EWM branches
099-005262-EW501
22.11.2016
35
12 Appendix B
12.1 Overview of EWM branches
Loading...